-
Graco 222121 - page 1
Instructions – Parts List GRACO INC.ąP .O. BOX 1441ąMINNEAPOLIS, MNą55440-1441 Copyright 1988, Graco Inc. is registered to I.S. EN ISO 9001 ST AINLESS STEEL, W A TERBASE COMP A TIBLE Fluid Pressure Regulator For use in air–assisted system to regulate pressure to gun. Fluid regulator valve is cartridge mounted for quick, in–line replacement ...
-
Graco 222121 - page 2
2 307886 Symbols W arning Symbol W ARNING This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions. Caution Symbol CAUTION This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions. W ARNING INSTRUCTIONS EQUIPMENT MISUSE HAZARD Equipment ...
-
Graco 222121 - page 3
307886 3 W ARNING INJECTION HAZARD Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely serious injury , including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury . D Fluid injected into the skin might look like just a cut, but it is a serious injury . ...
-
Graco 222121 - page 4
4 307886 Installation KEY A Air regulator B Bleed-type master air valve C Pump D Fluid filter & drain valve E Main fluid supply line F Gun fluid supply line G Fluid regulator H Fluid pressure gauge & drain valve J Air-assisted spray gun K Back pressure valve L Fluid return line M Main circulating line N Fluid supply container AB C D E F J K ...
-
Graco 222121 - page 5
307886 5 Operation Pressure Relief Procedure W ARNING INJECTION HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying accidentally . Fluid under high pressure can be injected through the skin and cause serious injury . T o reduce the risk of an injury from injection, splashing fluid, or moving parts, f ...
-
Graco 222121 - page 6
6 307886 Maintenance Flushing D Flush before changing colors, before fluid can dry in the equipment, at the end of the day , before storing, and before repairing equipment. D Flush at the lowest pressure possible. Check connectors for leaks and tighten as necessary . D Flush with a fluid that is compatible with the fluid being dispensed and the equ ...
-
Graco 222121 - page 7
307886 7 Maintenance Diaphragm & V alve Actuator Replacement W ARNING T o reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 5. 1. Relieve the pressure. 2. Remove the regulator from the fluid line. 3. Remove the six cap screws (19) from the regulator housing (24 ...
-
Graco 222121 - page 8
8 307886 Notes ...
-
Graco 222121 - page 9
307886 9 T roubleshooting W ARNING T o reduce the risk of serious bodily injury , including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, always follow the Pressure Relief Procedure on page 5 whenever the pump is shut off, before installing, cleaning, adjusting, removing or servicing the valve or any part of th ...
-
Graco 222121 - page 10
10 307886 Parts Drawing 25 { 7* 8* 6* 4* 5* 3* 2* 1* 24 19 lubricate lubricate T orque to 30 to 35 ft-lb (41 to 47 N-m) Apply medium strength sealant. T orque to 60 to 70 in-lb (7 to 8 N-m). T orque in sequence shown in Fig. 2. **27 **9 **26 14 lubricate 15 14 lubricate 16 18 17 12 13 Ref No. Qty 11 21 31 41 51 61 71 81 lubricate lubricate * V alve ...
-
Graco 222121 - page 11
307886 11 Parts List Ref. No. Part No. Description Qty . 1* 187882 HOUSING, valve; SST 1 2* 102982 O-RING; PTFE 1 3* 1 1 1737 SPRING, compression, conical; SST 1 4* 183876 GASKET , seat, nylon 1 5* 101680 BALL; carbide 1 6* 183875 SEA T , valve; carbide 1 7* 107505 O-RING, PTFE 1 8* 188001 RET AINER, spring; SST 1 9** 235204 ACTUA TOR, valve; carbi ...
-
Graco 222121 - page 12
12 307886 Performance Charts 0.4 0 200 400 600 800 1000 1200 01 0.2 0.6 0.8 1.2 1.4 0 200 400 600 800 1000 1200 01 0.2 0.4 0.6 0.8 GPM (liter/min) T est Media: 65 centipoise at 1500 psi (10.3 MPa, 103 bar) inbound pressure psi (MPa, bar) psi (MPa, bar) (8.3, 83) (7, 69) (5.5, 55) (4.2, 41) (2.8, 28) (1.4, 14) (3.8) (0.8) (1.5) (2.3) (3) (4.5) (5.3) ...
-
Graco 222121 - page 13
307886 13 T echnical Data Maximum fluid inlet pressure 1500 psi . . . . . . . . . . . . . . (10.3 MPa, 103 bar) Regulated pressure range 150 to 1200 psi . . . . . . . . . . (1 to 8.3 MPa, 10.4 to 83 bar) Maximum flow capacity 1.5 gpm (5.7 lpm) . . . . . . . . . . Fluid viscosity 1 to 1000 centipoise . . . . . . . . . . . . . . . . . Weight 4.5 lb ( ...
-
Graco 222121 - page 14
14 307886 Graco Standard W arranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco w ill, for a period of twelve months from the ...
¿Tienes una pregunta acerca de Graco 222121?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Graco 222121, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Graco 222121 probablemente compartirá una forma de solucionarlo.