Ultra electronic Sicura Laminatorの取扱説明書

24ページ 2.94 mb
ダウンロード

ページに移動 of 24

Summary
  • Ultra electronic Sicura Laminator - page 1

    Ultra Electronics Card Systems Quick Start Guide MAGICARD Sicura Laminator Page 1 MAGICARD Sicura Lami nator Quick Start Guide Laminator Setup Iss. 09 Janu ary 03 3504-22-01 Stock No. M9004-593 DCR 27634 refers ...

  • Ultra electronic Sicura Laminator - page 2

    Quick Start Guide Ultra Electronics Card Systems Page 2 MAGICARD Sicura Laminator Setting up your Sicura Laminator t akes just two easy step s: 1. Unpack and install the laminator A Preparing a Location for the Laminator B Removing the Laminator from the Box C Check the Packag e Contents D Install the Lamination Film E Connect the Laminator to a Po ...

  • Ultra electronic Sicura Laminator - page 3

    Ultra Electronics Card Systems Quick Start Guide MAGICARD Sicura Laminator Page 3 Location Requirements for yo ur laminator/printer: Preparing a Location for the Sicura Laminator and Printer A • An adequate power supply. • Ambient temperature +10 to +30 deg C. • Relative Humidity 20/70% RH. • Protection from direct sunlight and chemicals. ? ...

  • Ultra electronic Sicura Laminator - page 4

    Quick Start Guide Ultra Electronics Card Systems Page 4 MAGICARD Sicura Laminator Removing the Laminator from the Box Carefully open the box and remove any accessories. Place on a smooth, level surface and remove the polyethylene container. B ...

  • Ultra electronic Sicura Laminator - page 5

    Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Laminator Page 5 Checking the Package Contents C The MagiCard Sicura Card Laminator Envelope containing this Quick-Start guide A Roll of Lamination Film and a Take-up Core (only supplied when ordered w ith the Laminator) A P owe r C o r d wi t h M o l d e d P l u g fo r your country? ...

  • Ultra electronic Sicura Laminator - page 6

    Quick Start Guide Ultra Electronics Card Systems Page 6 MAGICARD Sicura Laminator Check that the Mains Supply Voltage is correct for your country. (Different models are manufactured for each supply voltage.) ...

  • Ultra electronic Sicura Laminator - page 7

    Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Laminator Page 7 Install the Lamination Film D Lift the transparent cover and move the roller lever to the OPEN position. Gently install the roll of film between the rollers. The black alignment marks on the film should be innermost. Turn the fastener ¼ turn counter- clockwise and r ...

  • Ultra electronic Sicura Laminator - page 8

    Quick Start Guide Ultra Electronics Card Systems Page 8 MAGICARD Sicura Laminator Gently turn both rolls, to ensure that there is no slack film. Close the transparent cover. Replace and fasten the film retaining plate, and close the lever. ...

  • Ultra electronic Sicura Laminator - page 9

    Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Laminator Page 9 Connect the Laminator to a Power Supply E Check that the Laminator operating voltage is correct for your supply voltage. (Units cannot be changed from one voltage to another.) Check that the temperature Controller’s LED’s flash. Connect to the AC supply and s wit ...

  • Ultra electronic Sicura Laminator - page 10

    Quick Start Guide Ultra Electronics Card Systems Page 10 MAGICARD Sicura Lam inator The temperature will achieve the set point level after a delay of 4 minutes, and the READY indicator will illuminate. Notes: 1. When switched on, the laminating roller and take-up roll turn for 30 seconds or until a black alignment panel is found by the optical sens ...

  • Ultra electronic Sicura Laminator - page 11

    Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 11 NOTE: The optimum roller temperature is best determined by trial and error, using your own cards and laminating film. The following notes are for your guidance only. • Cards with large, unprinted white areas require a higher temperature for lamination. • We rec ...

  • Ultra electronic Sicura Laminator - page 12

    Quick Start Guide Ultra Electronics Card Systems Page 12 MAGICARD Sicura Lam inator Insert a card into the slot, side to be laminated uppermost. Cards should be clean, dust-free and not already overcoated. Adjust the IN/OUT position of the laminate on the card by screwing the core in or out, if necessary. The card will be laminated in 35- 40 second ...

  • Ultra electronic Sicura Laminator - page 13

    Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 13 Adjust the roller te mperature for good laminate adhesion as required (up to 200 ° C max). The display normally shows the roller core temperature in ° C. Adjust the setpoint temperature with the ↑ and ↓ keys as desired. Press the Scroll Key once to return to ...

  • Ultra electronic Sicura Laminator - page 14

    Quick Start Guide Ultra Electronics Card Systems Page 14 MAGICARD Sicura Lam inator IMPORTANT NOT E FOR SETTING U P YOUR RIO/TANGO PRI NTER DRIVER TO WORK WITH THE SICURA LA MINATOR – Please select the appropriate option in yo ur printer driver for best results. It is necessary to make the correct settings to the overcoat page in your printer dri ...

  • Ultra electronic Sicura Laminator - page 15

    Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 15 Note: The Rio/Tango printer can print cards faster than the Sicura can laminate them. There is a hopper capacity of abou t 12 cards, but to reduce the speed discrepancy, it is recommended that the printer is operated in ColorSure mode (refer to the Rio/Tango Quick- ...

  • Ultra electronic Sicura Laminator - page 16

    Quick Start Guide Ultra Electronics Card Systems Page 16 MAGICARD Sicura Lam inator Notes: 1. If the Magi c ard ca rd pri n ter pri n ts a card befo re the lamin ato r is ready (ie not ful ly a rm ed up , or still laminating the previous card), the card is held w ithin the body of the printer until the lami nator is read y, and f urt her p rint ing ...

  • Ultra electronic Sicura Laminator - page 17

    Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 17 I Operating the Hopper/Sicura in Stand Alone Mode Clip the Card Feed Ho pper to the end of the Sicura card laminator and remove the Card Deflection Plate. Load the hopper w ith cards to be laminated (100 cards maximum). Connect the interface cable from the lamintor ...

  • Ultra electronic Sicura Laminator - page 18

    Quick Start Guide Ultra Electronics Card Systems Page 18 MAGICARD Sicura Lam inator The Card Feed Hopper has been factory set for use with 30 thou cards. Should it require adjustment, carry out the following procedure: Adjusting the Hopper J Remove the hopper from the lam i nato r, remove the interface cable. View the cards edge-on at the card exit ...

  • Ultra electronic Sicura Laminator - page 19

    Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 19 The Sicura card laminator has three indicators to tell you what is happening: READY (Green) - When lit, indicates that it is ready to laminate a card. When flashing, indicates that it is still warming up. When off, either busy laminating a card, or the po w er is o ...

  • Ultra electronic Sicura Laminator - page 20

    Quick Start Guide Ultra Electronics Card Systems Page 20 MAGICARD Sicura Lam inator Correction operation depends on clean rollers to tr ansport cards, an undamage d laminating roller, and a dust-free environment. It is recommended that the laminator be cleaned after every roll of lamination film (250 cards). PREPARATION Set the temperature controll ...

  • Ultra electronic Sicura Laminator - page 21

    Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 21 Check the Installation : • Repeat the installation steps in this guide. • Check that the laminator mains voltage is correct. • Check that the laminating film is the right way round and passes through the optical sensor. • Check that the unit has warmed up ( ...

  • Ultra electronic Sicura Laminator - page 22

    Quick Start Guide Ultra Electronics Card Systems Page 22 MAGICARD Sicura Lam inator Notice The information contained in this document is subject to change with out notice. Ultra Electronics Limited shall not be liable for errors contained herein or for incidental consequential damages in connection with the furnishing, performance or use of this ma ...

  • Ultra electronic Sicura Laminator - page 23

    Ultra Electronics Card Sy stems Quick Start Guide MAGICARD Sicura Lamina tor Page 23 Limited Warr ant y Informat ion 1) Coverage: Ultra E lectronics Ltd Warrants that the MAGICARD Sicura ca rd laminator shipped with this Warranty stateme nt will conform to the manufacturers specifications an d be free from defects in materials or workmanship for a ...

  • Ultra electronic Sicura Laminator - page 24

    Quick Start Guide Ultra Electronics Card Systems Page 24 MAGICARD Sicura Lam inator EC Declaration of Conformity Manufacturer's Name: Ultra Electronics Li mited. Manufacturer's Address: Waverley House, Hampshire Road, Granby Estate, W e y m o u t h , Dorset DT4 9XD E n g l a n d . declares that the produ cts Product Name: MAGICARD Sicura? ...

メーカー Ultra electronic カテゴリー Laminator

Ultra electronic Sicura Laminatorのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Sicura Laminatorの取扱説明書
- Ultra electronicの製品カード
- パンフレット
- またはUltra electronic Sicura Laminatorの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Ultra electronic Sicura Laminatorの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Ultra electronic Sicura Laminatorの取り付け説明書、サービスマニュアル、簡易説明書、またはUltra electronic Sicura Laminatorのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Ultra electronic Sicura Laminatorの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Ultra electronic Sicura Laminatorデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがUltra electronic Sicura Laminatorを使用するのを助ける技術的文書のことです。説明書は通常、全てのUltra electronic Sicura Laminatorユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Ultra electronicの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Ultra electronic Sicura Laminatorの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははUltra electronic Sicura Laminatorの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Ultra electronic Sicura Laminatorに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Ultra electronic Sicura Laminatorデバイスの基本機能を使うにあたってのヒント。 Ultra electronic Sicura Laminatorのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Ultra electronic Sicura Laminatorに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるUltra electronic Sicura Laminatorのメーカー/サービスへの連絡先に関する情報。

Ultra electronic Sicura Laminatorについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもUltra electronic Sicura Laminatorの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがUltra electronic Sicura Laminatorで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)