Manual Furuno M51A

22 pages 0.39 mb
Download

Go to site of 22

Summary
  • Furuno M51A - page 1

    DLM 600W Series P o w er Supplies M51A Option: Isolated Analog Programming Manual Power Supplies Elgar Electronics Corporation 9250 Brown Deer Road San Diego, CA 92121-2294 1-800-73ELGAR (1-800-733-5427) Tel: (858) 450-0085 Fax: (858) 458-0267 Email: sales@elgar.com www.el gar .co m ©2002 by Elgar Electronics Corporation This document contains inf ...

  • Furuno M51A - page 2

    . ...

  • Furuno M51A - page 3

    SAFETY NOTICE Before applying power to the system, verify that t he instrument is configured properly for the user’s particular application. WARNING! Hazardous voltages may be present when covers are removed. Qualified personnel must use extreme caution when servicing this equipment. Circuit boards, test points, and output voltages also may be fl ...

  • Furuno M51A - page 4

    SAFETY SYMBOLS ii ...

  • Furuno M51A - page 5

    ELGAR FIVE–YEAR WARRANTY Elgar Electronics Corporation (hereinafter referred to as Elgar) warrants its products to be free from defects in material and workmanship. This warranty is effective for one year from the date of shipment of the product to the original purchaser. Liability of Elgar under this warranty shall exist provided that: • the B ...

  • Furuno M51A - page 6

    This page intentionally left blank. iv ...

  • Furuno M51A - page 7

    CONTENTS SECTION 1 M51A OPTION OVERVIEW 1.1 Introduction ...................................................................................................... 1-1 1.2 General Description ......................................................................................... 1-1 1.3 Specifications.................................................. ...

  • Furuno M51A - page 8

    Contents DLM 600W Series LIST OF TABLES Table 2–1. INTFC SETUP Switch ............................................................................... 2-1 Table 2–2. ISOLATED ANALOG INTERFACE Connector Pinout .............................. 2-4 Table 2–3. Remote Programming Configuration Options ........................................... 2-7 T ...

  • Furuno M51A - page 9

    SECTION 1 1.1 Introduction 1.2 M51A OPTION OVERVIEW This addendum is to be used in conjunction with the DLM 600W Series Power Supplies Operation Manual, Sorensen Document No. M362161-01. The Sorensen M51A Option for the DLM 600W Series power supplies provides a remote analog interface, which has safety isolation from the output terminals. This allo ...

  • Furuno M51A - page 10

    M51A Option Overview DLM 600W Series 1.3 Specifications 1.3.1 1.3.2 Electrical Specifications Remote Voltage Programming Accuracy, 0-5/10V Inputs: Output Voltage: 0.5% of Vmax Output Current: 0.75% of Imax OVP: 1.0% of 1.1 X Vmax Remote 4-20mA Programming Accuracy: Output Voltage: 0.75% of Vmax Output Current: 1.0% of Imax Supplemental Characterist ...

  • Furuno M51A - page 11

    SECTION 2 2.1 ISOLATED REMOTE ANALOG INTERFACE OPERATION INTFC SETUP Switch The INTFC SETUP (Interface Setup) switch is accessible from the rear panel of the unit. It provides user selectability of the programming/monitoring ranges and signal types, as well as configuring the power supply for operation under remote control. Setting a switch to the ...

  • Furuno M51A - page 12

    Isolated Remote Analog Interface Operation DLM 600W Series 2-2 M51A Option 2.1.1 2.2 INTFC SETUP Switch Functions The following sections describe the functions of the various switch positions: V, 10V or 4-20mA Select: Position-1, when ON, selects 0-10VDC programming of the output voltage. Also, must be set to ON position when the ISOLATED ANALOG IN ...

  • Furuno M51A - page 13

    DLM 600W Series Isolated Remote Analog Interface Operation M51A Option 2-3 Figure 2–1. Rear Panel View, Low–Voltage Models Figure 2–2. Rear Panel View, High–Voltage Models ...

  • Furuno M51A - page 14

    Isolated Remote Analog Interface Operation DLM 600W Series 2-4 M51A Option 2.3 Isolated Analog Interface Connector The ISOLATED ANALOG INTERFACE connector is a 25-position female Subminiature-D type. Pin Function 1 ANALOG-CONTROL input 2 Return for 0-5/10V monitor outputs and EXTERNAL-OFF 3 OVP programming input 4 Voltage monitor output, 4-20mA 5 V ...

  • Furuno M51A - page 15

    DLM 600W Series Isolated Remote Analog Interface Operation M51A Option 2-5 2.3.1 ISOLATED ANALOG INTERFACE Functions The following sections describe the functions of the various signals of the ISOLATED ANALOG INTERFACE. Pin numbers correspond to the connector pinout of Table 2–2. Digital Control Input Signals ANALOG-CONTROL: Pin-1, enables remote ...

  • Furuno M51A - page 16

    Isolated Remote Analog Interface Operation DLM 600W Series 2-6 M51A Option Analog Programming Signals OVP PROGRAMMING INPUT: Pin-3, an input signal of 0-5 volts or 0-10 volts (user selectable with INTFC SETUP switch) programs the OVP threshold from 5-110% of full scale output voltage. Signal is referenced to Pin-12. Circui t is SELV, and has electr ...

  • Furuno M51A - page 17

    DLM 600W Series Isolated Remote Analog Interface Operation M51A Option 2-7 CURRENT RESISTANCE PROGRAMMING OUTPUT: Pin-22 provides a 1mA current source which would be connected to Pin-10, CURRENT PROGRAMMING INPUT, with a 0-5k Ω external resistor connected between Pin-22 to Pin-12, to program the output current from 0-100% of full scale output. Th ...

  • Furuno M51A - page 18

    Isolated Remote Analog Interface Operation DLM 600W Series 2-8 M51A Option 2.4.1 2.4.2 2.4.3 Voltage Source Progra mming of Output Voltage Setting up for voltage source programming of the output voltage is as follows: 1. Set Position-1, V, of the INTFC SETUP switch to OFF (down) for 0-5VDC programming range. 2. Set Position-1, V, of the INTFC SETUP ...

  • Furuno M51A - page 19

    DLM 600W Series Isolated Remote Analog Interface Operation M51A Option 2-9 4. Program the other parameters to the desired limit values: VOLTAGE PROGRAMMING INPUT, Pin-9, and the CURRENT PROGRAMMING INPUT, Pin-10, with respect to Pin-12. 5. Connect Pin-1, ANALOG-CONTROL, of the ISOLATED ANALOG INTERFACE connector to Pin-15. 2.4.4 2.4.5 Resistance Pr ...

  • Furuno M51A - page 20

    Isolated Remote Analog Interface Operation DLM 600W Series 2-10 M51A Option 2.4.6 2.4.7 2.4.8 Resistance Programming of OVP Setting up for resistance programming OVP is as follows: 1. Set Position-3, OVP, of the INTFC SETUP switch to OFF (down) for 0-5VDC programming range. 2. Connect the external programming resistance, 0-5k Ω , to the ISOLATED ...

  • Furuno M51A - page 21

    DLM 600W Series Isolated Remote Analog Interface Operation M51A Option 2-11 3. Connect a jumper from Pin-13 to Pin-12. 4. Connect a jumper from Pin-11 to Pin-23. 5. Program the other parameters to the desired limit values: VOLTAGE PROGRAMMING INPUT, Pin-9, and the OVP PROGRAMMING INPUT, Pin-3, with respect to pin-12. 6. Connect Pin-1, ANALOG-CONTRO ...

  • Furuno M51A - page 22

    Isolated Remote Analog Interface Operation DLM 600W Series 2-12 M51A Option 2.7 Remote Digital Status Signals Digital signals are available for remote monitoring the operational status of the unit. Refer to Table 2–5 for information on the characteristics of the signals. ISOLATED ANALOG INTERFACE Connections Logic Levels (with No Signal Output Cu ...

Manufacturer Furuno Category Power Supply

Documents that we receive from a manufacturer of a Furuno M51A can be divided into several groups. They are, among others:
- Furuno technical drawings
- M51A manuals
- Furuno product data sheets
- information booklets
- or energy labels Furuno M51A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Furuno M51A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Furuno M51A, service manual, brief instructions and user manuals Furuno M51A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Furuno M51A.

Similar manuals

A complete manual for the device Furuno M51A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Furuno M51A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Furuno M51A.

A complete Furuno manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Furuno M51A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Furuno M51A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Furuno M51A, that we can find in the current document
3. Tips how to use the basic functions of the device Furuno M51A - which should help us in our first steps of using Furuno M51A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Furuno M51A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Furuno M51A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Furuno M51A?

Use the form below

If you did not solve your problem by using a manual Furuno M51A, ask a question using the form below. If a user had a similar problem with Furuno M51A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)