Manual Zephyr 700

13 pages 0.1 mb
Download

Go to site of 13

Summary
  • Zephyr 700 - page 1

    ELECTRONICS, LTD 700 SERIES SCPC Satellite Receivers ZEPHYRUS ELECTRONICS, LTD 1 68 South 122 East Avenue, Tulsa, OK 74128-2405 USA Phone 918-437-3333 Fax 918-438-7322 Web site http://www.big-z.com Email support@big-z.com ...

  • Zephyr 700 - page 2

    Thank you for using our equipment. We will do our best to earn your continuing confidence in Zephyrus and our products. Any time you need information or help, give us a call at 918-437-3333 (US). thankyou.sam We make quality affordable It's a good idea to look the equipment over for any shipping damage as soon as it is received. If damage is d ...

  • Zephyr 700 - page 3

    OPERATING THE ZEPHYRUS 700 SERIES SCPC SATELLITE RECEIVER Table of Contents SECTION 1 General Information -An overview and summary description of the system describing features and design philosophy. -System specifications and typical operating criteria. SECTION 2 Front Panel Layout and Operation -Meter operation and calibration, control informatio ...

  • Zephyr 700 - page 4

    The 700 receiver system is contained in a 3½" frame and features microcomputer electronics that control and monitor operation of either one or two receiver modules and the LNB. Primary power is normally 117 vac with 240 volt units available. Rack mounting is optional. v Input signal to the receiver is L band at 950-1450 MHz and is usually sup ...

  • Zephyr 700 - page 5

    Zephyrus 700 SCPC Satellite Receiver Specifications and Typical Operating Criteria PHYSICAL: General: Front panel is sloped back for easy viewing and data entry. Analog meters for signal values. Keypad entry tuning. Illuminated LCD readout of frequencies and operating status. Audio level controls on front panel. No. of carriers: One basic with fron ...

  • Zephyr 700 - page 6

    700 Front Panel Operation Refer to illustration in Section 1 The 700 is flexible, easy to operate, and provides you with the information needed to tell what's "going on." The RELATIVE RF meter actually indicates the amount of limiting taking place in the CARRIER 1 IF/Demod section. The adjustment, directly beneath it, lets the meter ...

  • Zephyr 700 - page 7

    An attempt to enter frequencies outside the permissible range will yield an error message indicating an INVALID FREQ . Other FAULT MESSAGES are: LNBO Little or no current is flowing to the LNB (LNB Open) LNBS Abnormally low resistance on the LNB line (LNB Short) FAULT - (followed by any combination of the digits 1,2,3,4,or5 ) 1,2,3 indicate loss of ...

  • Zephyr 700 - page 8

    Installation of the 700 Receiver system We assume your dish has been mounted and installed correctly and that you know how to make polarization and position adjustments. INPUT SIGNAL to the 700 is via the F connector labeled LNB 950-1450 MHZ. This signal must be supplied from an LNB or block-converter that is frequency stable to within ±50 kHz or ...

  • Zephyr 700 - page 9

    audio. Program audio that has no popping or static noise, but which is distorted (or is the wrong level) does not come from the above areas. Distortion problems come from audio processing circuits. This can be in the transmission processing, or the receiver demod and audio circuits. BACK INDOORS When you install your 700 in the rack, the first thin ...

  • Zephyr 700 - page 10

    System Operation and Customization The 700 Series SCPC system can be assembled in a large variety of configurations to meet specific requirements. COMPONENTS to make up a 700 system consist of the following: 1: Basic chassis/case which contains power supply, microcomputer control, and a complete front panel. See "700 Front Panel Operation" ...

  • Zephyr 700 - page 11

    MHz feed is removed from an operating demod causing AFC to lock out of range. It may require up to a minute for lockup when the 70 MHz baseband feed is restored. ALARM RELAY (J-1) NO and NC contacts are available to drive external customer equipment. The alarm relay is a miniature type (rated at 1 amp AC max) and is intended to drive control type c ...

  • Zephyr 700 - page 12

    System Operation MA700SYS.SAM SECTION 43 Figure 1 Channel 1 Receiver Board (Channel 2 is similar but less tuner) ...

  • Zephyr 700 - page 13

    MA700SYX.SAM Figure 2 700 Receiver Back Panel SECTION 4, PAGE 4 ...

Manufacturer Zephyr Category Satellite Radio

Documents that we receive from a manufacturer of a Zephyr 700 can be divided into several groups. They are, among others:
- Zephyr technical drawings
- 700 manuals
- Zephyr product data sheets
- information booklets
- or energy labels Zephyr 700
All of them are important, but the most important information from the point of view of use of the device are in the user manual Zephyr 700.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Zephyr 700, service manual, brief instructions and user manuals Zephyr 700. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Zephyr 700.

Similar manuals

A complete manual for the device Zephyr 700, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Zephyr 700 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Zephyr 700.

A complete Zephyr manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Zephyr 700 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Zephyr 700, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Zephyr 700, that we can find in the current document
3. Tips how to use the basic functions of the device Zephyr 700 - which should help us in our first steps of using Zephyr 700
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Zephyr 700
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Zephyr 700 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Zephyr 700?

Use the form below

If you did not solve your problem by using a manual Zephyr 700, ask a question using the form below. If a user had a similar problem with Zephyr 700 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)