Manual Weber SILVER A

6 pages 2.32 mb
Download

Go to site of 6

Summary
  • Weber SILVER A - page 1

    SUMMIT ® BUILT - IN GAS GRILL DIMENSIONS THIS GAS APPLIANCE IS DESIGNED FOR OUTDOOR USE ONL Y . LOCA TING YOUR GRILL When determining a suitable location for your Summit ® gas grill installation, give attention to concerns such as exposure to wind, proximity to trafc paths, and keeping any gas supply lines as short as possible. Never locate th ...

  • Weber SILVER A - page 2

    2 30 1 / 4 " Built-In F r ame 34 1 / 4 " 24" min. 21" Access for electric on left hand side 6 1 / 4 " 3 3 / 4 " Gas Inlet 28 " G RIL L Note: F or a counter top treatment: Recommended 3 / 4 " inch o verhang. Notch front edge for frame to fully slide in. 6 1 / 4 " 3 3 / 4 " Gas Inlet 24" min. 24& ...

  • Weber SILVER A - page 3

    3 6 1 / 4 " 3 3 / 4 " Gas I nlet B (6 1 / 4 ") A (3 3 / 4 ") C Side view Plan View Left S ide Gas I nlet Dimensions Built-In Gas Line Dimensions 28" Grill 36" Grill T olerances A 3 3 / 4 " 3 3 / 4 "" + 1 / 8 " - 1 / 8 " B 6 1 / 4 " 6 1 / 4 " + 1 / 8 " - 1 / 8 " C 2 1 / 2 &qu ...

  • Weber SILVER A - page 4

    4 GAS LINE PIPING • Refer to the piping chart at the bottom of previous page. • The corrugated gas line from the manifold is 58 inches long. Do not extend the gas line. • We have provided the means to make an SAE 45° are connection. Do not use pipe sealant on this connection. • If the length of line required does not exceed 50 feet, use ...

  • Weber SILVER A - page 5

    5 1). At least one ventilation opening (a hole or group of holes, for the purpose of ventilation) needs to be on one side of the enclosure that communicates with the outside of the “island” structure. If a gas leak should occur or the LP cylinder should vent in the LP cylinder enclosure, the gas should not be allowed to vent or migrate into the ...

  • Weber SILVER A - page 6

    6 VENTILA TION  W ARNING: Air holes must be provided in the structure at the top and bottom to provide ventilation in the event of a gas leak. Air holes can be located in a low visibility area and should be protected by screening material to prevent rodents and insects from entering the structure. Air holes will also help dry moisture. Summit ® ...

Manufacturer Weber Category Universal Remote

Documents that we receive from a manufacturer of a Weber SILVER A can be divided into several groups. They are, among others:
- Weber technical drawings
- SILVER A manuals
- Weber product data sheets
- information booklets
- or energy labels Weber SILVER A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Weber SILVER A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Weber SILVER A, service manual, brief instructions and user manuals Weber SILVER A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Weber SILVER A.

Similar manuals

A complete manual for the device Weber SILVER A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Weber SILVER A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Weber SILVER A.

A complete Weber manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Weber SILVER A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Weber SILVER A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Weber SILVER A, that we can find in the current document
3. Tips how to use the basic functions of the device Weber SILVER A - which should help us in our first steps of using Weber SILVER A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Weber SILVER A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Weber SILVER A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Weber SILVER A?

Use the form below

If you did not solve your problem by using a manual Weber SILVER A, ask a question using the form below. If a user had a similar problem with Weber SILVER A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)