English dropdown-ico

Manual Pelco C2928M-QS

16 pages 0.93 mb
Download

Go to site of 16

Summary
  • Pelco C2928M-QS - page 1

    QUICK START GUIDE C2928M-QS (7/05) PMCD750 DLP ™ Display 50-Inch Rear Projection Display ...

  • Pelco C2928M-QS - page 2

    2 C2928M-QS (7/05) This quick start guide describes basic assembly and operation of the PMCD750 DLP ™ display as a stand-alone unit and as part of a video wall. BEFORE Y OU BEGIN DOCUMENTATION Refer to the enclosed CD for the following documentation: • Installation/Operation manual • Copy of this Quick Start Guide ...

  • Pelco C2928M-QS - page 3

    C2928M-QS (7/05) 3 Chassis Assembly Unpack the PMCD750 unit. The screen is not needed yet and should be left in its container at this time. SINGLE DISPLAY Attach the screen support to the front edge of the chassis with the supplied screen support bolts. The screen support mounts only one way . It incorporates a stop (rest) for the screen. Refer to ...

  • Pelco C2928M-QS - page 4

    4 C2928M-QS (7/05) W ALL DISPLAY – SECOND ROW AND UP Figure 2. T ie-Back Connection Points DANGER: Because the PMCD750 unit has a narrow front-to-back profile, the danger of tipping exists with high walls. For walls over two units high and all tilted walls, use the four tie-back points (1/4-20 threaded holes) on the rear of the unit to secure th ...

  • Pelco C2928M-QS - page 5

    C2928M-QS (7/05) 5 1. Stack another row of PMCD750 units on the first row . As you stack, be careful inserting the alignment pins on the second row chassis into the alignment holes on the lower unit. Refer to Figure 3. Figure 3. Alignment Pin Locations (Front View) WARNING: The maximum stack height for a wall is four units. ALIGNMENT PINS FIRST RO ...

  • Pelco C2928M-QS - page 6

    6 C2928M-QS (7/05) 2. As each unit is placed in the second row , secure it to the front of the lower unit with two 6-32 x 3/8-inch screws. Refer to Figure 4. Figure 4. Front Screw Securing Locations FRONT SCREW CONNECTION POINTS FRONT SCREW CONNECTION POINT DET AIL ...

  • Pelco C2928M-QS - page 7

    C2928M-QS (7/05) 7 3. Bolt the PMCD750 units together vertically through the vertical connection points using the 1/4-20 x 3/8-inch bolts. Refer to Figure 5. 4. Bolt the PMCD750 units together through the bottom connection points the same as the first row . Refer to Figure 1. 5. Bolt the PMCD750 units together through the horizontal connection poi ...

  • Pelco C2928M-QS - page 8

    8 C2928M-QS (7/05) Connecting Analog and Digital Sources The PMCD750 will accept video input from devices with VGA or DVI output. Video sources with either or both of these output types can have their images displayed on the PMCD750. Refer to Figure 6. Figure 6. Video Input Connections Connect the video input to the Analog 1, Analog 2, or Digital I ...

  • Pelco C2928M-QS - page 9

    C2928M-QS (7/05) 9 Connecting RS-232 and RS-485 Control Serial control can be used with stand-alone units, a wall, or several walls. To connect an external controller: 1. Using a straight-through computer serial cable, connect the RS-232 input of the stand-alone unit or the first unit in the wall to the serial out port of the external control devi ...

  • Pelco C2928M-QS - page 10

    10 C2928M-QS (7/05) Installing Screens To install a screen on a stand-alone unit, follow the instructions in steps 1a, 1b, and 1c. 1. T o install the PMCD750 screens, start in the middle of the bottom row and install that screen. The screen supports should be installed on the bottom row of PMCD750 screens. a. Pull the screen rails all the way out o ...

  • Pelco C2928M-QS - page 11

    C2928M-QS (7/05) 11 Figure 9. L-Shaped Screen Slot ...

  • Pelco C2928M-QS - page 12

    12 C2928M-QS (7/05) Connecting Power 1. Bring AC power next to the electronics module. Connect the power to the receptacle located on the rear panel. The voltage can be 115 V AC (90–132 VAC) or 230 V AC (200–254 V AC). Refer to Figure 10. Figure 10. Power Switch and Receptacles 2. The AC power can be looped through to the next PMCD750 unit, res ...

  • Pelco C2928M-QS - page 13

    C2928M-QS (7/05) 13 Using The Remote Control Using the the remote control is the only way to access menu settings. There are no access controls on the display unit. The remote control projects a series of IR (infrared) pulses to the PMCD750 display for control. Aim the remote control at a single display and press MENU. The main menu should be visib ...

  • Pelco C2928M-QS - page 14

    14 C2928M-QS (7/05) Alignment and Adjustment If the image on the screen is not positioned accurately , alignment of the optical engine may be required. It is important to check this mechanical adjustment of the optical engine before any electronic adjustments are made to the picture. Refer to the Aligning the Optical Engine section of the Installat ...

  • Pelco C2928M-QS - page 15

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series ...

  • Pelco C2928M-QS - page 16

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...

Manufacturer Pelco Category Projection Television

Documents that we receive from a manufacturer of a Pelco C2928M-QS can be divided into several groups. They are, among others:
- Pelco technical drawings
- C2928M-QS manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco C2928M-QS
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco C2928M-QS.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco C2928M-QS, service manual, brief instructions and user manuals Pelco C2928M-QS. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco C2928M-QS.

Similar manuals

A complete manual for the device Pelco C2928M-QS, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco C2928M-QS by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco C2928M-QS.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco C2928M-QS - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco C2928M-QS, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco C2928M-QS, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco C2928M-QS - which should help us in our first steps of using Pelco C2928M-QS
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco C2928M-QS
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco C2928M-QS in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco C2928M-QS?

Use the form below

If you did not solve your problem by using a manual Pelco C2928M-QS, ask a question using the form below. If a user had a similar problem with Pelco C2928M-QS it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)