Manual Snapper 1721302-04

22 pages 1.04 mb
Download

Go to site of 22

Summary
  • Snapper 1721302-04 - page 1

    A TT A CHMENT OPERA T OR’S MANU AL Snow Plo w/Dozer Blade Mfg. No. Description 1693754 42” Remote Angling Snow Plow/Dozer Blade Hitch Mfg. No. Description 1693756 Hitch (for Baron Series, Broadmoor / 1600 / 2600 Series, & Landlord / 1700 / 2700 Series) 1721302-04 Rev 1/2001 TP 100-2356-04-AT-SMA Sno w/Doz er Blade & Hitc h ...

  • Snapper 1721302-04 - page 2

    1 T able of Contents Adjustments .........................................................7 Skid Shoe Adjustment .....................................7 Spring T ension .................................................7 Lift Height Adjustment .....................................8 Downw ard Pressure Adjustment .....................8 Initial Setup &a ...

  • Snapper 1721302-04 - page 3

    OPERA TING SAFETY O Always clear snow up and down the face of slopes, never across the face. Exercise extreme caution when changing direction on slopes. Do not attempt to clear steep slopes. O Exercise extreme caution when operating on, or crossing, gravel drives, walks or roads. Stay alert for hidden hazards or traffic. O After striking an object ...

  • Snapper 1721302-04 - page 4

    3 TRA CT OR CONTROLS Before you begin operating the tractor with the dozer blade attachment, make certain you have: • Read and understood the instructions in the tractor Operator’s Manual. • Become thoroughly familiar with all of the tractor controls and their operation, including how to safely and properly start and stop the unit. • Practi ...

  • Snapper 1721302-04 - page 5

    4 Checks Bef ore Starting 1. Refer to the Maintenance & Adjustments sections of this manual and perform any needed service. Also, refer to the tractor Operator’s Manual and perform any required service. 2. Remove any objects from the work area which might interfere with plowing activity. 3. Adjust the skid shoes to desired height. See Skid Sh ...

  • Snapper 1721302-04 - page 6

    5 General Operating Instructions Daily Stora ge 1. Allow tractor engine to cool before storing in any enclosure. 2. After dozing or plowing jobs are completed, hose or brush down the blade to remove excess dirt. 3. Lightly oil all pivot points. Coat bare metal surfaces to prevent corrosion. IMPORT ANT NO TE Refer to Tractor Operator’s Manual for ...

  • Snapper 1721302-04 - page 7

    6 Maintenance Schedule For Normal Care Care Required Schedule Clean debris from After each use. dozer blade. Lubricate dozer blade. Every 10 hours or at least once a year. Lubricate Dozer Blade Lubricate the dozer blade as shown in Figure 2. Where an oil can is shown, wipe the area clean, apply a few drops of oil (SAE 30), then wipe up drips or spi ...

  • Snapper 1721302-04 - page 8

    7 Adjustments Skid Shoe Adjustment Slotted holes are provided to permit adjustment of the shoe assemblies for raising and lowering the blade to various working heights (see Figure 3). When cleaning snow from gravel or earth drives or walks, the shoe assemblies should be lowered fully to prevent blade contact with gravel or ground. When cleaning smo ...

  • Snapper 1721302-04 - page 9

    8 Adjustments Figure 6. Adjusting Lift Rod A. Front Set Collar B. Rod Guide C. Spring D. Rear Set Collar E. Spring Clip Figure 7. Lift Lever Quadrant - Side View Notch 1 Notch 2 Notch 3 Lift Rod Adjustment ELECTRIC/HYDRAULIC LIFT MODELS: In the fully raised position the blade should be 6” off the ground. In the fully lowered position, the lift ro ...

  • Snapper 1721302-04 - page 10

    9 Initial Setup & Assembly Ref Qty Description 1 1 ROD, Control Handle, Upper 2 6 NUT, Hex, 5/16-18 3 2 LOCKWASHER, 5/16 4 4 WASHER, 5/16 5 2 CAPSCREW, 5/16-18 x 1-1/4 6 1 ROD, Control Handle, Lower 7 1 CLEVIS 8 1 WASHER, 1/2 9 1 CLIP, Hair Pin 10 3 COTTER PIN 11 1 ROD & PLATE ASMY, Pivot 12 1 DOZER BLADE ASMY, 42” 13 1 SCRAPER BAR 14 6 C ...

  • Snapper 1721302-04 - page 11

    10 Initial Setup & Assembly 2 1 3 5 6 7 8 10 16 17 18 28 30 31 29 28 12 13 14 15 32 9 9 9 11 20 22 23 24 25 26 27 19 21 9 9 4 4 3 34 33 43 43 35 36 37 38 41 37 42 40 37 39 NOTE: The dashed-line rod: Landlord/1700/2700-This rod is part of the tractor. Broadmoor/1600/2600-This rod is the cross-shaft of the manual lift lever Ref Qty Description 1 ...

  • Snapper 1721302-04 - page 12

    11 Initial Setup & Assembly INITIAL SETUP & ASSEMBL Y NOTE: Some of the following setup procedures may already be completed. Assemble Blade 1. Place the blade on a flat surface. 2. Baron/Broadmoor/LT/1600/2600 Series: See Figure 10. Install one bar stop (A) using the two 5/16-18 x 1 taptite screws (B). Do not install second bar stop. Landlo ...

  • Snapper 1721302-04 - page 13

    12 Initial Setup & Assembly Install Rear Push Bar Support NOTE: Manual Lift Models-If your tractor is not already equipped with a Large Lift Lever kit, install it at this time. Follow the instructions supplied with the kit. 1. Assemble the push bar support (A, Figure 12) and hitch (F) using the hardware shown in Figure 12. Do not tighten the 5/ ...

  • Snapper 1721302-04 - page 14

    13 Initial Setup & Assembly Figure 15. Install Push Bar Assembly A. Push Bar Assembly C. Clevis Pins B. Hitch D. Safety Clips Figure 14. Installing Hitch to Rear Bracket A. Push Bar Support C. Lift Rod/Lever B. Washers CONNECT HITCH TO REAR PUSH BAR 1. Slide the push bar support (A, Figure 14), and wash- ers (B), onto the lift lever rod/lever ( ...

  • Snapper 1721302-04 - page 15

    14 Initial Setup & Assembly Install Spring Assist Bracket (Baron/Br oadmoor/1600/2600 Models Onl y) NOTE: Spring-assist bracket assembly (Figure 16) does not need to be installed on units with electric/hydraulic lift. 1. Install the spring-assist bracket (A, Figure 16) to trac- tor frame (bracket is mounted underneath frame). Secure with capscr ...

  • Snapper 1721302-04 - page 16

    15 Initial Setup & Assembly Install Lift Rod NOTE: Two lift rods are packaged with the Broadmoor/LT/1600/2600 & Landlord/GT/1700/2700 hitch assembly. Use the correct lift rod for manual or hydraulic lift as shown in Figure 9. 1. Assemble lift rod per Figure 19. 2. Insert prong of rod guide (A, Figure 20) through hole in upright of lift arm ...

  • Snapper 1721302-04 - page 17

    16 Initial Setup & Assembly Figure 23. Control Rod Support A. Support B. 5/16-18 x 1-1/2 Capscrews C. 5/16 Centerlock Nuts D. 5/16 Plain Washers E. Spacers Install Angling Control Rod NOTE: If installing the dozer attachment on a unit equipped with a snowcab, replace the control rod sup- port (A, Figure 23) with the hanging support (Ref. No. 40 ...

  • Snapper 1721302-04 - page 18

    17 Removing & Attaching the Hitch & Blade REMO V AL & INST ALLA TION Removing & Attac hing Dozer Blade 1. Lower the blade. Put the lift lever in the middle notch (float position). 2. Remove the hair pin clip and washer (D, Figure 25) securing the angling control rod to the clevis. Disconnect the angling control rod. 3. Remove the an ...

  • Snapper 1721302-04 - page 19

    18 Removing & Attaching Removing & Attac hing Hitch 1. Remove the safety clip (A, Figure 26) and remove the hitch pin (D). 2. Lift the hitch bar (B) off the tractor brackets (C). 3. Remove the spring clips (A, Figures 28 & 29) secur- ing the rear hitch bracket (C) to the lift pivot rod (B). 4. Hydraulic/Electric Lift Models: Slide the l ...

  • Snapper 1721302-04 - page 20

    19 Reinforcement Bracket Installation INST ALL REINFORCEMENT BRA CKET NOTE: This kit applies to the Landlord / 1700 / 2700 Series hydraulic lift models only. 1. Loosen the four capscrews (A, Figure 32) securing the quadrant (B) to the footrest. 2. Insert the reinforcement bracket (B, Figure 31) between the quadrant (B, Figure 32) and foot rest. Ali ...

  • Snapper 1721302-04 - page 21

    T orque Specification Chart FOR ST ANDARD MACHINE HARDW ARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68 7.7 1/4-20 66 7.6 8 10.9 12 16.3 1/4-28 76 8.6 ...

  • Snapper 1721302-04 - page 22

    Simplicity Mfg. Inc. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA © Copyright 2001 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA. ...

Manufacturer Snapper Category Automobile Accessories

Documents that we receive from a manufacturer of a Snapper 1721302-04 can be divided into several groups. They are, among others:
- Snapper technical drawings
- 1721302-04 manuals
- Snapper product data sheets
- information booklets
- or energy labels Snapper 1721302-04
All of them are important, but the most important information from the point of view of use of the device are in the user manual Snapper 1721302-04.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Snapper 1721302-04, service manual, brief instructions and user manuals Snapper 1721302-04. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Snapper 1721302-04.

A complete manual for the device Snapper 1721302-04, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Snapper 1721302-04 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Snapper 1721302-04.

A complete Snapper manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Snapper 1721302-04 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Snapper 1721302-04, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Snapper 1721302-04, that we can find in the current document
3. Tips how to use the basic functions of the device Snapper 1721302-04 - which should help us in our first steps of using Snapper 1721302-04
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Snapper 1721302-04
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Snapper 1721302-04 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Snapper 1721302-04?

Use the form below

If you did not solve your problem by using a manual Snapper 1721302-04, ask a question using the form below. If a user had a similar problem with Snapper 1721302-04 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (1)

河野幸太郎

容量の大きいHDDに取り変えたいのですがそのまま差し替えるだけでいいのでしょうか