English dropdown-ico

Manual Elo TouchSystems 282P101110000

28 pages 2.91 mb
Download

Go to site of 28

Summary
  • Elo TouchSystems 282P101110000 - page 1

    User’s Manual No. 980346-001 Rev. A ©2001 Zebra Technologies Corporation 2824 Thermal Printer User’s Manual ...

  • Elo TouchSystems 282P101110000 - page 2

    ii 980346-001 Rev. A ...

  • Elo TouchSystems 282P101110000 - page 3

    FOREWORD This manual provides installation and operation information for the LP 2824 series printers, manu - factured by Zebra Technologies Corporation, Camarillo, California. COPYRIGHT NOTICE This document contains information proprietary to Zebra Technologies Corporation. This docu - ment and the information contained within is copyrighted by Zeb ...

  • Elo TouchSystems 282P101110000 - page 4

    SHOCK HAZARD WARNING: The printer and power supply should never be operated in a location where either one can get wet. Personal injury could result. MEDIA WARNING: Always use high quality approved labels, tags and transfer ribbons. If adhesive backed labels are used that DO NOT lay flat on the backing liner, the exposed edges may stick to the labe ...

  • Elo TouchSystems 282P101110000 - page 5

    980346-001 Rev. A v TABLE OF CONTENTS Installation and Operation . . . . . . . . . . . . . . . . . 1 Unpacking Your Printer . . . . . . . . . . . . . . . . . . . . 2 Getting To Know Your Printer . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 AutoSense Gap Sensor Adjustment . . . . . . . . . ...

  • Elo TouchSystems 282P101110000 - page 6

    vi 980346-001 Rev. A ...

  • Elo TouchSystems 282P101110000 - page 7

    1 Installation and Operation This section provides information on the installation and operation of the printer. The printer is a low cost, desktop direct thermal printer. The printer is specifically designed for printing labels, tags or continuous receipts (with or without bar codes) from any DOS™, Win- dows™or ASCII-based compatible host. 980 ...

  • Elo TouchSystems 282P101110000 - page 8

    Unpacking Your Printer 2 980346-001 Rev. A Installation and Operation ...

  • Elo TouchSystems 282P101110000 - page 9

    Getting To Know Your Printer 980346-001 Rev. A 3 Installation and Operation ...

  • Elo TouchSystems 282P101110000 - page 10

    Installation The following steps will guide you through the installation of the printer and software. Step ➊ Attach Power Supply To The Printer See the SHOCK HAZARD WARNING on page iv. 4 980346-001 Rev. A Installation and Operation Power OFF Check Voltage Plug in Power Module Plug in Power Cord Plug Power Cord into a Suitable AC Outlet ...

  • Elo TouchSystems 282P101110000 - page 11

    Step ➋ Attach Interface Cable The printer has either a parallel interface or a serial interface (with optional RJ-11 connector). For additional information on serial cable wir - ing, refer to Appendix A. 980346-001 Rev. A 5 Installation and Operation Parallel Interface Power OFF RJ-11 Interface (Optional) Serial Interface ...

  • Elo TouchSystems 282P101110000 - page 12

    Step ➌ Load Labels 6 980346-001 Rev. A Installation and Operation MO VIE Open Cover Power ON Adjust Holders 1.0 inch 2.5 cm 1.5 inch 3.8 cm MO VIE ...

  • Elo TouchSystems 282P101110000 - page 13

    Load Labels - continued 980346-001 Rev. A 7 Installation and Operation Install Roll Remove Outside Length For more infor - mation refer to appendix A MO VIE ...

  • Elo TouchSystems 282P101110000 - page 14

    Load Labels - continued If the indicator remains dark, see Appendix A - Troubleshooting. 8 980346-001 Rev. A Installation and Operation Close Cover Tap Feed Button Thread Through Guides ...

  • Elo TouchSystems 282P101110000 - page 15

    Step  AutoSense Gap Sensor Adjustment Perform this procedure when loading a new roll. If your printer has the label dispenser option, turn OFF the label taken sensor. 980346-001 Rev. A 9 Installation and Operation Power ON Hold Feed Button Power OFF MO VIE ...

  • Elo TouchSystems 282P101110000 - page 16

    AutoSense Gap Sensor Adjustment - continued If the indicator remains orange or red, see the troubleshooting steps. 10 980346-001 Rev. A Installation and Operation 4 MO3351F 16 V3.21 Serial port : 96,N,8,1 Image buffer size:245K Fmem:000,0K,019.9K avl Gmem:000K,0241K avl E I8,0,001 rY S2 D8 R016,000 ZT UN q800 Q1029,025 Option: 04 08 13 now in DUMP ...

  • Elo TouchSystems 282P101110000 - page 17

    Label Dispenser Option 980346-001 Rev. A 11 Installation and Operation Open Door Use a Stylus to Switch On the Label Taken Sensor Remove Several Labels Push Liner Through Slot Close Door MO VIE ...

  • Elo TouchSystems 282P101110000 - page 18

    Using Fan-Fold Media 12 980346-001 Rev. A Installation and Operation Open Guides to Width of Media Lock Guides in Place Thread Media Through Guides Insert Media ...

  • Elo TouchSystems 282P101110000 - page 19

    Step ➎ Install Software Start your computer and follow the installation instructions on the compact disc (CD). 980346-001 Rev. A 13 Installation and Operation ...

  • Elo TouchSystems 282P101110000 - page 20

    14 980346-001 Rev. A Installation and Operation ...

  • Elo TouchSystems 282P101110000 - page 21

    Appendix A - Troubleshooting Problem Solution or Reason STATUS Indicator Does not light when power switch is turned to ON (I) position. 1. Check power connections from A.C. outlet to power supply to printer. Lights GREEN, but printer will not print. 1. Check interface cable connections from computer to printer. 2. Make sure top cover is locked clos ...

  • Elo TouchSystems 282P101110000 - page 22

    Problem Solution or Reason Prints only partial label or skips a label. 1. Perform AutoSense gap sensor adjustment on page 8. 2. Label caught on print head. 3. Print head is not properly latched. 4. Possible software problem. Check the printer memory configuration. Refer to the EPL2 Programming manual. Printing stops and STATUS indicator lights ORAN ...

  • Elo TouchSystems 282P101110000 - page 23

    Serial Interface Cable Wiring The figure below displays the cable wiring required to use the printer's RS-232 serial interface. 980346-001 Rev. A 17 Appendix A - Troubleshooting N/C RxD TxD DTR GND DSR RTS RI CTS Pri nter Hos t 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 DB -9 Pi n # DB -9 Pi n # F ema le DB-9 to M ale DB-9 Cable P/N 300017-006 ( 6&ap ...

  • Elo TouchSystems 282P101110000 - page 24

    18 980346-001 Rev. A Cash Drawer Cable Wiring The figure below displays the pin assignments for the printer's retail cash drawer interface. Re - fer to the cash draw manufacturer's documenta - tion for proper drawer wiring. *+24 volts D.C. at no greater than 1.5 amps. Appendix A - Troubleshooting PRINTER RJ- 11 Pi n N o . M ale R J-11 SGN ...

  • Elo TouchSystems 282P101110000 - page 25

    980346-001 Rev. A 19 Parallel Interface Cable Wiring The figure below displays the cable wiring required to use the printer's Centronics parallel interface. +5 volts at 300 mA for external device (e.g. KDU or scanner) Appendix A - Troubleshooting PRINTER DB - 25 Pi n No . Centroni cs Pi n No . F e m a l eD B - 2 5t oM a l eC e n t r o n i c s ...

  • Elo TouchSystems 282P101110000 - page 26

    20 980346-001 Rev. A Cleaning the Print Head When you load new media, you can also clean the print head. Appendix A - Troubleshooting Rub Cleaning Pen Across Dark Area of Print Head Wait One Minute Before Closing Printer Do Not Clean Roller MO VIE ...

  • Elo TouchSystems 282P101110000 - page 27

    980346-001 Rev. A 21 Preparing Media, Paper, and Labels Before Loading During shipment, the outside length of media may become dirty when handled or dusty when stored. A preparation before loading media makes sure both the print head and platen stay cleaner for more time. You must avoid dragging adhesive or dirty media between the print head and pl ...

  • Elo TouchSystems 282P101110000 - page 28

    980346 - 001A ...

Manufacturer Elo TouchSystems Category Printer

Documents that we receive from a manufacturer of a Elo TouchSystems 282P101110000 can be divided into several groups. They are, among others:
- Elo TouchSystems technical drawings
- 282P101110000 manuals
- Elo TouchSystems product data sheets
- information booklets
- or energy labels Elo TouchSystems 282P101110000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Elo TouchSystems 282P101110000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Elo TouchSystems 282P101110000, service manual, brief instructions and user manuals Elo TouchSystems 282P101110000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Elo TouchSystems 282P101110000.

Similar manuals

A complete manual for the device Elo TouchSystems 282P101110000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Elo TouchSystems 282P101110000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Elo TouchSystems 282P101110000.

A complete Elo TouchSystems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Elo TouchSystems 282P101110000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Elo TouchSystems 282P101110000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Elo TouchSystems 282P101110000, that we can find in the current document
3. Tips how to use the basic functions of the device Elo TouchSystems 282P101110000 - which should help us in our first steps of using Elo TouchSystems 282P101110000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Elo TouchSystems 282P101110000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Elo TouchSystems 282P101110000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Elo TouchSystems 282P101110000?

Use the form below

If you did not solve your problem by using a manual Elo TouchSystems 282P101110000, ask a question using the form below. If a user had a similar problem with Elo TouchSystems 282P101110000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)