Manual Hitachi DH 22PB

72 pages 0.94 mb
Download

Go to site of 72

Summary
  • Hitachi DH 22PB - page 1

    DOUBLE INSULATION DOUBLE ISOLATION AISLAMIENTO DOBLE MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE AVERTISSEMENT Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la mort ou de sérieuses blessures corporelles! Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit. Prière de l ...

  • Hitachi DH 22PB - page 2

    CONTENTS English Page IMPORTANT SAFETY INFORMATION ........ 3 MEANINGS OF SIGNAL WORDS .......... 3 SAFETY ................................................... 4 GENERAL SAFETY RULES ................. 4 SPECIFIC SAFETY RULES AND SYMBOLS ..... 6 DOUBLE INSULATION FOR SAFER OPERATION ..................................... 8 FUNCTIONAL DESCRIPTION ..... ...

  • Hitachi DH 22PB - page 3

    3 English IMPORTANT SAFETY INFORMATION Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accid ...

  • Hitachi DH 22PB - page 4

    4 English SAFETY GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS 1. Work Area (1) Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. (2) Do not operat ...

  • Hitachi DH 22PB - page 5

    5 English (3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. (4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in person ...

  • Hitachi DH 22PB - page 6

    6 English SPECIFIC SAFETY RULES AND SYMBOLS 1. Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. 2. ALWAYS wear ear protectors when using the tool for exte ...

  • Hitachi DH 22PB - page 7

    7 English 14. Keep motor air vent clean. The tool’s motor air vent must be kept clean so that air can freely flow at all times. Check for dust build-up frequently. 15. Operate power tools at the rated voltage. Operate the power tool at voltages specified on its nameplate. If using the power tool at a higher voltage than the rated voltage, it will ...

  • Hitachi DH 22PB - page 8

    8 English DOUBLE INSULATION FOR SAFER OPERATION To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation” means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by th ...

  • Hitachi DH 22PB - page 9

    9 English Fig. 1 SPECIFICA TIONS Motor Single-Phase, Series Commutator Motor Power Source Single-Phase, 120 V 60 Hz Current 5.4 A Capacity Concrete: 1/8" ~ 15/16" (3.4 mm ~ 22 mm) Steel: 1/2" (13 mm) W ood: 1-1/4" (32 mm) No-Load Speed 0 – 1050/min. Full-load Impact Rate 0 – 4400/min. W eight 5.1 lbs (2.3 kg) FUNCTIONAL DESC ...

  • Hitachi DH 22PB - page 10

    10 English ASSEMBL Y AND OPERA TION APPLICA TIONS Rotation and hammering function 䡬 Drilling anchor holes 䡬 Drilling holes in concrete 䡬 Drilling holes in tile Rotation only function 䡬 Drilling in steel or wood (with optional accessories) 䡬 T ightening machine screws, wood screws (with optional accessories) PRIOR TO OPERA TION 1. Power so ...

  • Hitachi DH 22PB - page 11

    11 English Dust Cup Dust Collector (B) Drill bit Part of SDS-plus shank Grip Front cap Fig. 2 6. Mounting the drill bit ( Fig. 2) CAUTION: To prevent accidents, make sure to turn the switch off and disconnect the plug from the receptacle. NOTE: When using tools such as bull points, drill bits, etc., make sure to use the genuine parts designated by ...

  • Hitachi DH 22PB - page 12

    12 English CAUTION: 䡬 The dust cup and dust collector (B) are for exclusive use of concrete drilling work. Do not use them for wood or metal drilling work. 䡬 Insert dust collector (B) completely into the chuck part of the main unit. 䡬 When turning the rotary hammer on while dust collector (B) is detached from a concrete surface, dust collecto ...

  • Hitachi DH 22PB - page 13

    13 English 2. Rotation + Hammering This rotary hammer can be set to rotation and hammering mode by pressing the push button and turning the change lever to mark. (Fig. 7) (1) Mount the drill bit. (2) Pull the trigger switch after applying the drill bit tip to the drilling position. (Fig. 8) (3) Pushing the rotary hammer forcibly is not necessary at ...

  • Hitachi DH 22PB - page 14

    14 English 䡬 Drill bit may snap off while withdrawing the rotary hammer from the drilled hole. For withdrawing, it is important to use a pushing motion. 䡬 Do not attempt to drill anchor holes or holes in concrete with the main unit in the rotation only function. 䡬 Do not attempt to use the rotary hammer in the rotation and striking function w ...

  • Hitachi DH 22PB - page 15

    15 English 6. Using depth gauge (Fig. 12) (1) Loosen the knob on the side handle, and insert the depth gauge into the mounting hole on the side handle. (2) Adjust the depth gauge position according to the depth of the hole and tighten the knob bolt securely . 7. How to use the drill bit (taper shank) and the taper shank adaptor (1) Mount the taper ...

  • Hitachi DH 22PB - page 16

    16 English (1) Mount the core bit to the core bit shank. (Fig. 15) Lubricate the thread of the core bit shank to facilitate disassembly . (2) Mount the core bit shank to the rotary hammer . (Fig. 16) (3) In sert the center pin into the guide plate until it stops. (4) Engage the guide plate with the core bit, and turn the guide plate to left or righ ...

  • Hitachi DH 22PB - page 17

    17 English MAINTENANCE AND INSPECTION W ARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection. 1. Inspecting the drill bits Since use of a dull tool will cause motor malfunctioning and degraded efficiency , replace the drill bit with a new one or resharpening without delay when abrasion is ...

  • Hitachi DH 22PB - page 18

    18 English ACCESSORIES WARNING: ALWAYS use Only authorized HITACHI replacement parts and accessories. NEVER use replacement parts or accessories which are not intended for use with this tool. Contact HITACHI if you are not sure whether it is safe to use a particular replacement part or accessory with your tool. The use of any other attachment or ac ...

  • Hitachi DH 22PB - page 19

    19 English T aper mode Code No. Applicable drill bit 7/16" (11 mm) 1/2" (12.3 mm) 303617 1/2" (12.7 mm) 9/16" (14.3 mm) 9/16" (14.5 mm) 11/16" (17.5 mm) 303618 7/8" (21.5 mm) A-taper 303619 B-taper 303620 External dia. Code No. 7/16" 944460 (11 mm) 1/2" 944461 (12.3 mm) 1/2" 993038 (12.7 mm) 9/16&qu ...

  • Hitachi DH 22PB - page 20

    20 English <Outer wedge type with the female screw> Anchor size W 1/4" W 5/16" W 3/8" (6.3 mm) (8 mm) (9.5 mm) Overall Length 10-1/4" 10-1/4" 6-1/4" 10-1/4" (260 mm) (260 mm) (160 mm) (260 mm) Code No. 302976 302975 303621 302974 <Inner wedge type with the headless screw> Anchor size W 1/4" W 5/16 ...

  • Hitachi DH 22PB - page 21

    21 English Core bit (outer diameter) Core bit shank –– 1"(25 mm) 982672 Overall length 1-1/8" (29 mm) 982673 4-1/8" 303625 (A) 1-1/4" (32 mm) 982674 (A) (105 mm) (A) 982684 1-3/8" (35 mm) 982675 12" 303626 1-1/2" (38 mm) 982676 (300 mm) (B) 982685 (B) 1-3/4" (45 mm) 982677 (B) 12" 303627 2" (50 ...

  • Hitachi DH 22PB - page 22

    22 English 6. Drilling holes and driving screws (rotation only) 䡬 Drill chuck, chuck adaptor and chuck wrench Special screw Code No. 981122 Drill chuck (13VLRB–D) (includes chuck wrench) Code No. 321814 Chuck adaptor (G) (SDS-plus shank) Code No. 303623 Chuck wrench 7. Drilling holes (rotation only) Drill chuck (13VLD–D) (includes chuck wrenc ...

  • Hitachi DH 22PB - page 23

    23 English 9. Dust cup, Dust collector (B) Dust cup Code No. 971787 Dust collector (B) Code No. 306885 10. Hammer grease A 1.1 lbs (500 g) (in a can) Code No. 980927 0.15 lbs (70 g) (in a green tube) Code No. 308471 0.07 lbs (30 g) (in a green tube) Code No. 981840 NOTE: Specifications are subject to change without any obligation on the part of the ...

  • Hitachi DH 22PB - page 24

    24 Français INFORMA TIONS IMPORT ANTES DE SÉCURITÉ Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé. La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé ...

  • Hitachi DH 22PB - page 25

    25 Français SECURITE REGLES GENERALE DE SECURITE AVERTISSEMENT: Lire et coxmprendre toutes les instructions. Un non respect de toutes les instructions ci-dessous peut entraîner une électrocution, un incendie et/ou de sérieuses blessures personnelles. CONSERVER CES INSTRUCTIONS 1. Zone de travail (1) Garder la zone de travail propre et bien écl ...

  • Hitachi DH 22PB - page 26

    26 Français moment d’inattention lors de l’utilisation de l’outil motorisé peut entraîner de sérieuses blessures personnelles. (2) S’habiller correctement. Ne pas porter des vêtements larges ou des bijoux. Attacher les cheveux longs. Tenir ses cheveux, vêtements et ses gants éloignés des parties mobiles. Les vêtements larges, les b ...

  • Hitachi DH 22PB - page 27

    27 Français (8) Utiliser uniquement les accessoires recommandés par le fabricant pur le modèle utilisé. Des accessoires qui peuvent convenir à un outil, peuvent devenir dangereux lorsqu’ils sont utilisés avec un autre outil. 5. Réparation (1) La réparation de l’outil ne doit être réalisée uniquement par un réparateur qualifié. Une ...

  • Hitachi DH 22PB - page 28

    28 Français Ne pas utiliser un outil pour un usage pour lequel il n’a pas été prévu: par exemple, ne pas utiliser une scie circulaire pour couper des branches d’arbre ou des bûches. 9. NE JAMAIS utiliser un outil motorisé pour des applications autres que celles spécifiées. NE JAMAIS utiliser un outil motorisé pour des applications autr ...

  • Hitachi DH 22PB - page 29

    29 Français Essuyer les parties en plastique avec un chiffon doux légèrement imbibé d’une solution d’eau savonneuse et sécher minutieusement. 20. TOU J OURS porter des lunettes de protection qui respectent les dernières révisions du Standard ANSI Z87.1. 21. TOUJOURS vérifier s’il y a des objets encastrés, par exemple des fils électr ...

  • Hitachi DH 22PB - page 30

    30 Français DOUBLE ISOLA TION POUR UN FONCTIONNEMENT PLUS SUR Pour assurer un fonctionnement plus sûr de cet outil motorisé, HITACHI a adopté une conception à double insolation. “Double isolation” signifie que deux systèmes d’isolation physiquement séparés ont été utilisés pour isoler les matériaux conducteurs d’électricité co ...

  • Hitachi DH 22PB - page 31

    31 Français Carter Plaque signalétique Sélecteur DESCRIPTION FONCTIONNELLE REMARQUE: Les informations contenues dans ce mode d’emploi sont conçues pour assister l’utilisateur dans une utilisation sans danger et un entretien de l’outil motorisé. NE JAMAIS utiliser ni entreprendre une révision de l’outil sans avoir d’abord lu et compr ...

  • Hitachi DH 22PB - page 32

    32 Français ASSEMBLAGE ET FONCTIONNEMENT APPLICA TIONS Fonction de rotation et percussion 䡬 Perçage de trous d’ancrage 䡬 Perçage de trous dans béton 䡬 Perçage de trous dans une tuile Par action de rotation uniquement 䡬 Perçage de l’acier ou du bois (avec accessoires en option) 䡬 Serreage de vis mécaniques et de vis à bois (ave ...

  • Hitachi DH 22PB - page 33

    33 Français 6. Montage du foret de per ç age (Fig. 2) PRECAUTION: Pour éviter tout accident, bien couper l'interrupteur et débrancher la fiche de la prise. REMARQUE: Lorsqu'on utilise des outils comme des pointes à broyer , des forets, etc., bien utiliser des pièces d'origine conçues par notre société. (1) Nettoyer la sectio ...

  • Hitachi DH 22PB - page 34

    34 Français PRECAUTION: 䡬 La capuchon à poussière et le collecteur à poussière (B) ne sont destinés à être utilisés que lors du perçage de béton. Ne pas les utiliser lors du perçage de pièces en bois ou métalliques. 䡬 Insérer le collecteur à poussière (B) à fond dans le mandrin de l’appareil principal particules pour ne util ...

  • Hitachi DH 22PB - page 35

    35 Français un fonctionnement continu en pressant la détente et en relâchant le cliquet d’arrêt. Pour mettre l’interrupteur sur OFF (arrêt), presser de nouveau la détente et la ramener à sa position d’origine. 䡬 Si l’on tire sur la gâchette et qu’on appuie sur la butée, l’outil continue à tourner tout seul, ce qui est pratiq ...

  • Hitachi DH 22PB - page 36

    36 Français (1) Fixer le mandrin porte-foret sur le raccord. (2) L ’élément de la tige SDS est identique au foret de perçage. Se reporter à “Montage du foret de perçage” pour le fixer . PRECAUTION: 䡬 Si l’on applique une force excessive, cela donnera un travail bâclé et abîmera la pointe du foret de perçage, réduisant ainsi la ...

  • Hitachi DH 22PB - page 37

    37 Français 5. Enfoncement de vis à bois (Fig. 11) (1) Sélection d’une mèche appropriée Utilisez des vis à tête cruciforme, autant que possible étant donné que la mèche glisse souvent de la tête des vis ordinaires. (2) Enfoncement de vis à bois 䡬 A vant d’enfoncer des vis à bois, préparez d’abord des trous appropriés aux vis ...

  • Hitachi DH 22PB - page 38

    38 Français COMMENT UTILISER LA COURONNE (POUR UNE CHARGE LEGERE) Utiliser la couronne pour percer de grands trous. L ’utiliser avec le goujon central et la queue de couronne fournis en tant qu’accessoires en option. 1. Montage PRECAUTION: 䡬 S’assurer que l’interrupteur est sur la position d’arrêt (OFF) et débrancher l’outil. (1) M ...

  • Hitachi DH 22PB - page 39

    39 Français PRECAUTION: 䡬 Quand on retire le goujon central et la plaque de guidage, mettre l’interrupteur sur la position d’arrêt (OFF) et débrancher la perceuse. 3. Démontage (Fig. 19) Une autre méthode consiste à retirer la queue de la couronne du marteau rotatif à frapper fortement la tête de la queue de la couronne deux ou trois ...

  • Hitachi DH 22PB - page 40

    40 Français ENTRETIEN ET INSPECTION AVERTISSEMENT: S’assurer de mettre l’interrupteur d’alimentation sur la position OFF et de déconnecter la fiche de la prise secteur avant l’entretien et l’inspection de la meuleuse. 1. Contrôle du foret de perçage Etant donné que l’utilisation d’une mèche usée entraînera un mauvais fonctionn ...

  • Hitachi DH 22PB - page 41

    41 Français ACCESSOIRES AVERTISSEMENT: TOUJOURS utiliser UNIQUEMENT des pièces de rechange et des accessoires HITACHI. NE JAMAIS utiliser de pièce de rechange ou d’accessoires qui ne sont pas prévus pour être utilisé avec cet outil. En cas de doute, contacter HITACHI pour savoir si une pièce de rechange ou un accessoire particulier peuvent ...

  • Hitachi DH 22PB - page 42

    42 Français T upe de cône No. de code Foret de perçage utilisé 7/16" (11 mm) 1/2" (12,3 mm) 303617 1/2" (12,7 mm) 9/16" (14,3 mm) 9/16" (14,5 mm) 11/16" (17,5 mm) 303618 7/8" (21,5 mm) Cône en A 303619 Cône en B 303620 Dia. externe No. de code 7/16" 944460 (11 mm) 1/2" 944461 (12,3 mm) 1/2" 99 ...

  • Hitachi DH 22PB - page 43

    43 Français 2. Ancrage de chasse (Rotation + percussion) Régleur d’ancrage (pour fixation d’ancrage) (T ige SDS Plus) <T ype à cale extérieure avec vis femelle> Dimension de l’ancrage No. de code W1/4" 971794 (6,3 mm) W5/16" 971795 (8 mm) W3/8" 971796 (9,5 mm) W1/2" 971797 (12,7 mm) W5/8" 971798 (15,9 mm) &l ...

  • Hitachi DH 22PB - page 44

    44 Français Goujon No. de code No. de code Plaque centrale de guidage Couronne (diamètre externe) 1-1/4" (32 mm) 1-3/8" (35 mm) 1-1/2" (38 mm) Couronne (diamètre externe) 1-3/4" (45 mm) 2" (50 mm) No. de code 982686 982687 982688 No. de code 982689 982690 4. T ravail de démolissage (Rotation + percussion) No. de code Co ...

  • Hitachi DH 22PB - page 45

    45 Français 5. Mise en place du booulon pour d’ancre chimique (Rotation + percussion) Mandrin porte-foret (13VLRB-D) (y compris la clé de mandrin) No. de code 321814 Raccord (G) de mandrin (T ige SDS plus) No. de code 303623 V is spéciale No. de code 981122 Clé de mandrin 6. Perçage de trous et insertion des vis (rotation seulement) 䡬 Mand ...

  • Hitachi DH 22PB - page 46

    46 Français 9. Capuchon anti poussière, Collecteur à poussière (B) 10. Graisse A pour marteau 1,1 lbs (500 g) (en boîte) No. de code 980927 0,15 lbs (70 g) (en tube vert) No. de code 308471 0,07 lbs (30 g) (en tube vert) No. de code 981840 REMARQUE: Les spécifications sont sujettes à modification sans aucune obligation de la part de HIT ACHI ...

  • Hitachi DH 22PB - page 47

    47 Español INFORMACIÓN IMPORT ANTE SOBRE SEGURIDAD Antes de utilizar o de realizar cualquier trabajo de mantenimiento de esta herramienta eléctrica, lea y comprenda todas las precauciones de seguridad, advertencias e instrucciones de funcionamiento de este Manual de instrucciones. La mayoría de los accidentes producidos en la operación y el ma ...

  • Hitachi DH 22PB - page 48

    48 Español SEGURIDAD NORMAS GENERALES DE SEGURIDAD ADVERTENCIA: Lea y entienda todas las instrucciones. Si no sigue las instrucciones indicadas a continuación, pueden producirse descargas eléctricas, incendios, y/o lesiones serias. GUARDE EST AS INSTRUCCIONES 1. Área de trabajo (1) Mantenga el área de trabajo limpia y bien iluminada. Los banco ...

  • Hitachi DH 22PB - page 49

    49 Español 3. Seguridad personal (1) Esté siempre alerta y utilice el sentido común cuando utilice la herramienta eléctrica. No utilice la herramienta cuando esté cansado o bajo la influencia de medicamentos ni de alcohol. Un descuido al utilizar la herramienta eléctrica puede resultar en una lesión seria. (2) Vístase adecuadamente. No util ...

  • Hitachi DH 22PB - page 50

    50 Español de las herramientas. En caso de que una herramienta esté averiada, repárela antes de utilizarla. Muchos de los accidentes se deben a herramientas mal cuidadas. (8) Utilice solamente los accesorios recomendados por el fabricante para su modelo. Los accesorios adecuados para usar con una herramienta pueden ser peligrosos cuando se utili ...

  • Hitachi DH 22PB - page 51

    51 Español 8. Utilice la herramienta correcta. No fuerce herramientas ni accesorios pequeños para realizar un trabajo pesado. No utilice las herramientas para fines no proyectados, por ejemplo, no utilice esta amoladora angular para cortar madera. 9. NO utilice NUNCA una herramienta eléctrica para aplicaciones que no sean las especificadas. NO u ...

  • Hitachi DH 22PB - page 52

    52 Español 19. No limpie las partes de plástico con disolvente. Los disolventes, como gasolina, diluidor de pintura, bencina, tetracloruro de carbono, y alcohol pueden dañar o rajar las partes de plástico. No las limpie con tales disolventes. Limpie las partes de plástico con un paño suave ligeramente humedecido en agua jabonosa y después s? ...

  • Hitachi DH 22PB - page 53

    53 Español AISLAMIENTO DOBLE P ARA OFRECER UNA OPERACIÓN MÁS SEGURA Para garantizar una operación más segura de esta herramienta eléctrica, HIT ACHI ha adoptado un diseño de aislamiento doble. “Aislamiento doble” significa que se han utilizado dos sistemas de aislamiento físicamente separados para aislar los materiales eléctricamente c ...

  • Hitachi DH 22PB - page 54

    54 Español Carcase Placa de características Broca Sujetador DESCRIPCIÓN FUNCIONAL NOT A: La información contenida en este Manual de instrucciones ha sido diseñada para ayudarle a utilizar con seguridad y mantener esta herramienta eléctrica. NUNCA haga funcionar ni efectúe el mantenimiento de la herramienta antes de leer y comprender todas la ...

  • Hitachi DH 22PB - page 55

    55 Español MONT AJE Y OPERACIÓN APLICACIONES Función de rotación y golpeteo 䡬 Perforación de orificios de anclaje 䡬 Perforación de orificios de hormigón 䡬 Perforación de orificios de baldosa Rotación solamente 䡬 Perforación de orificios en hormigón o madera (con accesorios facultativos) 䡬 Apretar tornillos en metal o madera (co ...

  • Hitachi DH 22PB - page 56

    56 Español Broca Sujetador Fig. 2 Fig. 5 Fig. 4 Cubierta frontal Parte del SDS más vástago Colector de polvo (B) Capa de polvo 6. Montaje de la broca (Fig. 2) PRECAUCIÓN: Para evitar accidentes, cerciórese de desactivar y de desconectar el enchufe del tomacorriente. NOT A: Cuando ulilice herramientas como por ejemplo: cinceles, brocas de talad ...

  • Hitachi DH 22PB - page 57

    57 Español PRECAUCIÓN: 䡬 La copa de polvo y el colector de polvo (B) son para emplearse exclusvamente en trabajos de perforación de hormigón. No los emplee para trabajar con madera o metal. 䡬 Inserte completamente el colector de polvo (B) en la parte del portabrocas de la unidad principal. 䡬 Cuando ponga en funcionamiento del martillo per ...

  • Hitachi DH 22PB - page 58

    58 Español 䡬 Ti re del gatillo y empuje el tope para mantener activada la alimentación, lo cual es conveniente para un funcionamiento continuo. Cuando se lo desconecta, el tope puede quitarse tirando del gatillo otra vez. 2. Rotación + golpeteo Este martillo roto-percutor puede usarse en el modo de rotación y golpeteo presionando el pulsadory ...

  • Hitachi DH 22PB - page 59

    59 Español Broca Sujetador Cubierta frontal Cubo PRECAUCIÓN: 䡬 La aplicación de fuerza excesiva acelerará el trabajo pero dañará la punta de la broca y reducirá la vida útil del martillo perforador . 䡬 La broca puede salirse al quitar el martillo rotopercutor del orificio perforado. Para extraer esta herramienta es importante empujar ha ...

  • Hitachi DH 22PB - page 60

    60 Español 䡬 Luego de hacer rotar la herramienta lentamente hasta que el tornillo quede parcialmente metido en la madera, apretar más el gatillo para obtener la fuerza óptima de atornillado. PRECAUCIÓN: 䡬 T ener cuidado al preparar el orificio para que sea apropiado para el tornillo, teniendo en cuenta la dureza de la madera. Si el orificio ...

  • Hitachi DH 22PB - page 61

    61 Español MODO DE USAR LA BARRENA TUBULAR (P ARA CARGAS LIGERAS) Cuando se tengan que taladrar agujeros grandes, usar la barrena tubular (para cargas ligeras). Usar también el pasador central y la espiga de la barrena tubular provistos como accesorios opcionales. 1. Montaje PRECAUCIÓN: 䡬 Cerciorarse de poner el interruptor de la alimentación ...

  • Hitachi DH 22PB - page 62

    62 Español PRECAUCIÓN: 䡬 Cuando se quite el pasador central y la placa guía, poner el interruptor en la posición de OFF (apagado) y desconectar el enchufe de la toma de alimentación. 3. Desmontaje (Fig. 19) Como otro método, quitar la espiga de la barrena tubular del martillo perforador y golpear fuertemente la cabeza de la espiga de la bar ...

  • Hitachi DH 22PB - page 63

    63 Español MANTENIMIENTO E INSPECCIÓN ADVERTENCIA: Antes de realizar el mantenimiento o la inspección de la amoladora, cerciórese de OFF (desconectar) la alimentación y de desenchufar el cable de alimentación del tomacorriente. 1. Inspeccionar la broca de taladro Debido a que el uso de brocs desafiladas pueden causar mal funcionamiento del mo ...

  • Hitachi DH 22PB - page 64

    64 Español (1) Broca de taladro (Eje fino) (2) Adaptador para eje fino (SDS más vástago) (1) Broca de taladro (Vástago cónico) (2) Adaptador cónico (SDS más vástago) Chaveta (Núm. de código 944477) (1) Broca de taladro (Eje fino) (2) Adaptador para eje fino Diámetro externo Longitud efectiva Longitud total Núm. de código Núm. de códi ...

  • Hitachi DH 22PB - page 65

    65 Español Modo cónico Núm. de código Broca de taladro aplicable 7/16" (11 mm) 1/2" (12,3 mm) 303617 1/2" (12,7 mm) 9/16" (14,3 mm) 9/16" (14,5 mm) 11/16" (17,5 mm) 303618 7/8" (21,5 mm) Cono A 303619 Cono B 303620 Diámetro externo Núm. de código 7/16" 944460 (11 mm) 1/2" 944461 (12,3 mm) 1/2" ...

  • Hitachi DH 22PB - page 66

    66 Español <T ipo de reborde exterior con tornillo hembra> Medida de ancla W 1/4" W 5/16" W 3/8" (6,3 mm) (8 mm) (9,5 mm) Longitud total 10-1/4" 10-1/4" 6-1/4" 10-1/4" (260 mm) (260 mm) (160 mm) (260 mm) Núm. de código 302976 302975 303621 302974 <T ipo de reborde interior con tornillo sin cabeza> M ...

  • Hitachi DH 22PB - page 67

    67 Español Placa guia Barrena tubular (diámetro externo) 1-1/4" (32 mm) 1-3/8" (35 mm) 1-1/2" (38 mm) –– 1"(25 mm) 982672 Overall length 1-1/8" (29 mm) 982673 4-1/8" 303625 (A) 1-1/4" (32 mm) 982674 (A) (105 mm) (A) 982684 1-3/8" (35 mm) 982675 12" 303626 1-1/2" (38 mm) 982676 (300 mm) (B) 982 ...

  • Hitachi DH 22PB - page 68

    68 Español 6. Perforación (rotación solamente) 䡬 Portabrocas, adaptador del portabrocas, tornillo especál y llave de portabrocas Adaptador (G) de portabrocas (SDS más vástago) Núm. de código 303623 Broca para tornillos Plillips No. de broca T amaño del tornillo Longitud Núm. de código No.2 1/8" ~ 3/16" (3 – 5 mm) 31/32" ...

  • Hitachi DH 22PB - page 69

    69 Español 9. Copa de polvo, Colector de polvo (B) Copa de polvo Núm. de código 971787 Colector de polvo (B) Núm. de código 306885 10. Grasa A para martillo 1,1 libras (500 g) (en una lata) Núm. de código 980927 0,15 libras (70 g) (en un tubo verde) Núm. de código 308471 0,07 libras (30 g) (en un tubo verde) Núm. de código 981840 NOT A: ...

  • Hitachi DH 22PB - page 70

    70 ...

  • Hitachi DH 22PB - page 71

    71 AB C D 13 0 6 -345 1 23 0 6 -340 1 33 2 2 -809 1 43 2 2 -810 1 53 2 2 -811 1 63 2 2 -812 1 79 8 4 -118 1 89 3 9 -547 1 93 0 1 -654 4 D5 × 35 10 322-786 1 11 ––––––– 1 12 322-789 1 13 317-223 1 14 322-787 1 15 878-885 1 S-18 16 307-688 1 17 322-815 1 18 690-4DD 1 6904DDPS2L 19 322-819 1 20 322-813 1 21 959-156 1 D7.0 22 322-836 1 2 ...

  • Hitachi DH 22PB - page 72

    WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construc- tion activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● Lead from lead-based paints, ● Crystalline silica from bricks and cement and other mas ...

Manufacturer Hitachi Category Power Hammer

Documents that we receive from a manufacturer of a Hitachi DH 22PB can be divided into several groups. They are, among others:
- Hitachi technical drawings
- DH 22PB manuals
- Hitachi product data sheets
- information booklets
- or energy labels Hitachi DH 22PB
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hitachi DH 22PB.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hitachi DH 22PB, service manual, brief instructions and user manuals Hitachi DH 22PB. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hitachi DH 22PB.

Similar manuals

A complete manual for the device Hitachi DH 22PB, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hitachi DH 22PB by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hitachi DH 22PB.

A complete Hitachi manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hitachi DH 22PB - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hitachi DH 22PB, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hitachi DH 22PB, that we can find in the current document
3. Tips how to use the basic functions of the device Hitachi DH 22PB - which should help us in our first steps of using Hitachi DH 22PB
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hitachi DH 22PB
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hitachi DH 22PB in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hitachi DH 22PB?

Use the form below

If you did not solve your problem by using a manual Hitachi DH 22PB, ask a question using the form below. If a user had a similar problem with Hitachi DH 22PB it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)