Manual Siemens 150

20 pages 0.09 mb
Download

Go to site of 20

Summary
  • Siemens 150 - page 1

    Hicom 150 optiset E entr y s ...

  • Siemens 150 - page 2

    2 ...

  • Siemens 150 - page 3

    3 Introduction .............................................................................................. 4 Standard Features ................................................................................... 5 Internal and External Dialling ................................................................... 5 Dialling the Switchboard ........ ...

  • Siemens 150 - page 4

    4 Intr oduction This guide is designed to assist extension users on a Siemens Hicom 150 Communications System to use all authorised features. Your extension may not be authorised ∗ ∗ ∗ ∗ ∗ to use all features. The Siemens representative can confirm features that are available to you. Your extension may also be subject to trunk barring thu ...

  • Siemens 150 - page 5

    5 Internal and External Dialling Dialling Another Extension - lift handset, listen for internal dial tone - dial the required extension number Dialling an External Number - lift handset, listen for internal dial tone - dial line access code (code is normally 0 ) - dial the required external number V Your telephone may have restricted dialling facil ...

  • Siemens 150 - page 6

    6 Call T ransfer You may transfer an internal or external call from your extension to any other extension or to the switchboard. Transfer to a Free Extension (Announcing the Call) - press Transfer key, listen for internal dial tone - dial the required extension or switchboard - when the extension or the switchboard answers, announce the call and re ...

  • Siemens 150 - page 7

    7 Enquir y Call This feature allows you to hold an existing call, dial another extension or even an external number, conduct a conversation and then return to the original caller. Activate Enquiry Call - press Transfer key, listen for internal dial tone - dial the required extension number or dial 0 and then the required external number - conduct y ...

  • Siemens 150 - page 8

    8 Call Pic k Up The call pick up feature allows you to answer any ringing extension, in your pick up group, from your telephone. Activate Call Pick Up An extension within your pick-up group is ringing - lift handset, listen for internal dial tone - dial ∗ ∗ ∗ ∗ ∗ 21 - you will now have answered the call Activate Call Pick Up Select A call ...

  • Siemens 150 - page 9

    9 Call Bac k Call Back requests can be left on extensions which have been rung and not answered or are busy. Activate Call Back - Busy - called extension is busy - press Transfer key and ∗ ∗ ∗ ∗ ∗ 77 - confirmation tone is heard - replace handset The system will automatically call you back when both your extension and the called extension ...

  • Siemens 150 - page 10

    10 Call Bac k - Cont’ d Cancel Call Back (Before Ring Back) - lift handset - dial # 77 - confirmation tone is heard - replace handset All Call Back requests which you initiated will now be cancelled. ...

  • Siemens 150 - page 11

    11 Call P ark This feature allows you to Park an external call on your extension to be retrieved at any extension or from the switchboard. There are 10 Park positions (0-9 on keypad). Park a Call - press Transfer key and ∗ ∗ ∗ ∗ ∗ 92 plus location number (0-9) - replace handset - call is now parked Retrieve a Parked Call before Recall - d ...

  • Siemens 150 - page 12

    12 Call Forwar ding V ariable This feature allows you to forward or divert your calls immediately to an extension of your choice. Programme Call Forwarding - lift handset, listen for internal dial tone - dial ∗ ∗ ∗ ∗ ∗ 34 plus extension number - listen for confirmation tone - replace handset When you lift the handset special dial tone wil ...

  • Siemens 150 - page 13

    13 Call Forwar ding No Answer When this feature has been programmed your telephone will ring 5 times and then divert your calls to an extension of your choice. Programme Call Forwarding No Answer - lift handset, listen for internal dial tone - dial ∗ ∗ ∗ ∗ ∗ 35 plus extension number - listen for confirmation tone - replace handset Call Fo ...

  • Siemens 150 - page 14

    14 Electr onic T elephone Loc k This feature allows you to lock your extension, by dialling your PIN, which prevents unauthorised use of your extension. The PIN will be supplied by your System Administrator. Lock your Extension - lift handset - dial ∗ ∗ ∗ ∗ ∗ 95 and your PIN - listen for confirmation tone - replace handset Your extension ...

  • Siemens 150 - page 15

    15 Individual Abbreviated Dialling In addition to the System Abbreviated dialling lists you may programme 10 additional numbers, under the dial keypad digits 0-9, for your exclusive use. These numbers will, however, be subject to any trunk barring limits which apply to your extension. Programme numbers - dial ∗ ∗ ∗ ∗ ∗ 01 - enter digit (0 ...

  • Siemens 150 - page 16

    16 System Abbre viated Dialling The system allows for the storage of 1000 external telephone numbers. By utilising the system abbreviated dialling you will be permitted to dial specific numbers that would be outside your normal trunk barring limits. Use the System Abbreviated Dialling - select the relevant access code from your Abbreviated Dialling ...

  • Siemens 150 - page 17

    17 Timed Reminder Timed reminders or alarms can be programmed to remind you of meetings or appointments. Programme Timed Reminder - lift handset, listen for internal dial tone - dial ∗ ∗ ∗ ∗ ∗ 99 - Enter time e.g. 0945 or 1430 When Timed Reminder rings back lift and replace handset to cancel ring. Cancel Timed Reminder (before ringback) - ...

  • Siemens 150 - page 18

    18 Night Ser vice When the designated Night Service extension rings - lift handset, listen for internal dial tone - dial ∗ ∗ ∗ ∗ ∗ 24 - you are now connected to the caller Check with System Administrator if any other type of Night Service is operational. ...

  • Siemens 150 - page 19

    19 K e y Settings (+/–) The Plus and Minus keys allow for the individual setting of the levels of speech, ringing and ring tones. Change Speech Volume - whilst busy on a call - press + or – keys to adjust Speech volume - press + and – keys simultaneously to store setting Change Ringing volume or Ring Tone frequency - Do not lift handset - pre ...

  • Siemens 150 - page 20

    20 Siemens Telecommunications (Pty) Ltd. Private Bag X71 Halfway House 1685 Quic k Ref erence e n i L e d i s t u O0 e l b a i r a V d r a w r o F l l a C ∗ t x e & 4 3 r o t a r e p O9 s n A o N d r a w r o F l l a C ∗ t x e & 5 3 e l t t u h SR ∗ 9 7y s u B d r a w r o F l l a C ∗ t x e & 6 3 e c n e r e f n o C y a W 3R ∗ 8 ...

Manufacturer Siemens Category Telephone

Documents that we receive from a manufacturer of a Siemens 150 can be divided into several groups. They are, among others:
- Siemens technical drawings
- 150 manuals
- Siemens product data sheets
- information booklets
- or energy labels Siemens 150
All of them are important, but the most important information from the point of view of use of the device are in the user manual Siemens 150.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Siemens 150, service manual, brief instructions and user manuals Siemens 150. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Siemens 150.

Similar manuals

A complete manual for the device Siemens 150, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Siemens 150 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Siemens 150.

A complete Siemens manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Siemens 150 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Siemens 150, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Siemens 150, that we can find in the current document
3. Tips how to use the basic functions of the device Siemens 150 - which should help us in our first steps of using Siemens 150
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Siemens 150
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Siemens 150 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Siemens 150?

Use the form below

If you did not solve your problem by using a manual Siemens 150, ask a question using the form below. If a user had a similar problem with Siemens 150 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)