English dropdown-ico

Manual Microsoft UNO-3074

80 pages 2.87 mb
Download

Go to site of 80

Summary
  • Microsoft UNO-3074 - page 1

    i UNO-3074 Celer on M/ Pent ium M Embedded Automa tion Computer with Four PCI-Slot Extensions User Manual ...

  • Microsoft UNO-3074 - page 2

    UNO-3074 User Manual ii Copyright This document is co pyrighted, © 2007. All rights are reserved. The origi- nal manufact urer reserves the righ t to mak e impr ovements to the products described in this manual at any time with out notice. No part of this manual may be reproduced, copied, translated or transmi t- ted in any form or by any means wi ...

  • Microsoft UNO-3074 - page 3

    iii Product W arranty (2 years) Advantech warrants to you, the original purchaser , that each of its prod- ucts will be free from defects in material s and workmanshi p for two years from the date of purchase. This warranty does not apply t o any products which have be en repaired or altered by persons other than repair perso nnel authorized by Adv ...

  • Microsoft UNO-3074 - page 4

    UNO-3074 User Manual iv Declaration of Conformity CE This product has passed the CE test for environmental specificati ons when shielded cables are used for external wiring. W e recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for orderi ng information. FCC Class A Note: This e ...

  • Microsoft UNO-3074 - page 5

    v Safety Instructions 1. Read these safety instructions carefully . 2. Keep this user manual for later reference. 3. Disconnect thi s equipment from D C outlet before cleaning . Do not use liquid or spray deter gents for cleaning. 4. For pluggable equipment, the power outlet sh all be installed near the equipment and sha ll be easily accessible. 5. ...

  • Microsoft UNO-3074 - page 6

    UNO-3074 User Manual vi recommended by the manufacture. Discard used batteries accord- ing to the manufacturer ’ s instructions. 14. This device complies with Part 15 of th e FCC rules. Operation is subject to the following two condition s: (1) this device may not cause harmful interference, and (2) this device must accept any in terference recei ...

  • Microsoft UNO-3074 - page 7

    vii Table of Contents Contents Chapter 1 Overview .......................................................... 2 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Hardware Specifications ... ............... ........... .............. ........ 5 1.3 Safety Precautions ..... ......................... ... ...

  • Microsoft UNO-3074 - page 8

    UNO-3074 User Manual viii 2.6.1 Pin Assignments ............ ............. ........... .............. ........ 21 Figure 2.6:Digital Output C onnector Pin Assignments 21 Table 2.9:Digital Outp ut Connector Signals ................ 21 2.6.2 Power On Configuration .................. ........... ............. .... 22 Table 2.10:Digital Output Po wer O ...

  • Microsoft UNO-3074 - page 9

    ix Table of Contents 3.3 Installing a Hard Disk .......... .............. ............ .............. ... 41 Figure 3.1:IDE Connector (CN1 and CN2) .... ............. 45 3.4 Installing a PCI-bus Card ......................... .............. ......... 46 Figure 3.2:1st Anti-Vibration R ubber ....... ........... ........ 46 Figure 3.3:2nd PCI-bus Car ...

  • Microsoft UNO-3074 - page 10

    UNO-3074 User Manual x ...

  • Microsoft UNO-3074 - page 11

    CHAPTER 1 Overview This chapter provides an overvi ew of UNO-3074 specificatio ns. Sections include: • Introduct ion • Hardware specification • Safety precautions • Chassis dimensions ...

  • Microsoft UNO-3074 - page 12

    UNO-3074 User Manual 2 Chapter 1 Overview 1. 1 Introduction St a n d a r d PCs and some indu strial computers with a standard OS and hard- ware for the consumer market ca nnot provide the reliabil ity required by industrial aut omation and embedded industrial control applications. How- ever , many en gine ers pref er to use PCs because of their adv ...

  • Microsoft UNO-3074 - page 13

    3 Chapter 1 An Industry-Pr oven Design Industrial and mo bile applications require controller s with high -vibration specificatio ns and a wide temperature range. Machines or controll ers in light indu strial environm ents also require flexible and stable moun ting. Many machine builders underestimate the need for a more rugged control- ler because ...

  • Microsoft UNO-3074 - page 14

    UNO-3074 User Manual 4 Onboa rd DI/O for Counter , Alarm/Even t Handling UNO-3074 feat ures onboard DI and DO. These DIs and DOs can be used as 32-bit counters o r to handle alarms and events. Any events ca n be passed to UNO-3074 through DIs with an additional DI plug-in card. UNO-3074 can also output alarms through onboard DOs immedia tely to not ...

  • Microsoft UNO-3074 - page 15

    5 Chapter 1 1. 2 Hardware S pecificatio ns • CPU: Celeron M 1GHz CPU (non-cache) or Pentium M 1.4GHZ CPU( 2MB cache) or Pentium M 1.8GHz CPU( 2MB cache) • System Memory: 1x 200 pin SODIMM socket, supports up to 1GB DDR RAM • Battery Backup RAM: 512 KB • Chipset: Intel 855GME GMCH/ICH4 Chipset 400 MHz PSB (Celeron M 1G MHz Pentium M 1.4 GHz ...

  • Microsoft UNO-3074 - page 16

    UNO-3074 User Manual 6 • 4-ch Isolated Digit al In pu t (DI0 ~DI3) - 2,000 VDC isolation - 2,000 VDC ESD protection - 70 VDC over-voltage protectio n - -50~50 VD C input r ange and 10 kHz speed - Input V o ltage Range: Logic 0: -3 ~ 3 VDC Logic 1: -50 ~ -10 VDC, 10 ~ 50 VDC - Input Curren t: 10 VDC: 1.7 mA (typical) 12 VDC: 2.1 mA (typical) 24 VD ...

  • Microsoft UNO-3074 - page 17

    7 Chapter 1 1 Grms w/HDD@IEC 68 sec. 2-64, ra ndom, 5~500Hz, 1 Oct ./min, 1hr axis • Power Supply: 16 ~ 36 VDC • Operating T emperatur e: -10 ~ 55° C (14 ~ 131° F) • Rela tive Hum idity: 0~95% @ 40° C (n on-condensin g) • Power Consum ption: 24 W (T ypical) • Power Requir ement: Min 96 W , (16~36 VDC) (e.g. +24 V @ 4A ) • Chassis Siz ...

  • Microsoft UNO-3074 - page 18

    UNO-3074 User Manual 8 1. 4 Chassis Dimen sions Figure 1.1: Chassis Dimensions for CeleronM 1GHz ...

  • Microsoft UNO-3074 - page 19

    9 Chapter 1 Figure 1.2: Chassis for P entium 1.8GHz or Fa ster CPU ...

  • Microsoft UNO-3074 - page 20

    UNO-3074 User Manual 10 1. 5 Packing List The accessory package of UNO-3 074 contains the following items: (A) Power cable (B) Keyboard/ Mouse PS/2 cable (C) W arranty card (D) Driver and Utility CD-ROM (E) 4 x nti-vibration rubber (F) PCI expansion to hold 2nd anti-vibration ru bber (G) Mini Jumper (H) Paper menu ( I ) Power connector (J) IDE cabl ...

  • Microsoft UNO-3074 - page 21

    CHAPTER 2 Hardware Functionality This chapter shows how t o setup the UNO-3074 hard ware functi ons, incl ud- ing connecting peripherals, and setting switches and i ndicators. Sections include: • Introduction • RS-232 Interface • RS-232 /422/485 Interface • LAN / Ethern et Connector • DI/O and Counter • Power Connector • LED and Buzze ...

  • Microsoft UNO-3074 - page 22

    UNO-3074 User Manual 12 Chapter 2 Hardware Functionality 2. 1 Introduction The two figures below show the connectors on UNO-3074, and following sections give you detailed in formation about functi on of each peripheral. Figure 2.1: Front Panel of UNO-3074 ...

  • Microsoft UNO-3074 - page 23

    13 Chapter 2 2. 2 RS-232 Interfa ce (C OM 1~C OM 2) The UNO-3074 offers two industrial standard RS-232 serial communica- tion interface ports: COM1 and COM2. Please refer to Appendix A .4 for their pin assignments. The IRQ and I/O address range of COM1 and COM2 are listed bel ow: COM1: 3F8 H , IRQ4 COM2: 2F8 H , IRQ3 2. 3 RS-232/422/485 Interface ( ...

  • Microsoft UNO-3074 - page 24

    UNO-3074 User Manual 14 2.3.4 RS-232/4 22/48 5 Select ion COM3 and COM4 support 9-wire RS-232, RS-4 22 and RS-485 interfaces. The system detects RS-422 or RS-485 signals automa tically in RS-42 2/ 485 mode. T o select between RS-422/485 and RS-232 for COM 3, adjust JP4. T o select between RS-422/485 and RS-232 for COM4 , adjust JP5. Y ou can refer ...

  • Microsoft UNO-3074 - page 25

    15 Chapter 2 2.3.6 IRQ, I/O Ad dress a nd T ransmission Rate Set ting The IRQ and I/O address range of COM3 and COM4 are listed bel ow: • COM3: 3E8 H , IRQ10 (Independ ent IRQ), IRQ10 (Share IRQ) • COM4: 2E8 H , IRQ5 (Independent IRQ), IRQ10 (Sha re IRQ) • V ect or addr ess for shar e IRQ: 1D0 H Yo u can set “Share IRQ” or “Indepen dent ...

  • Microsoft UNO-3074 - page 26

    UNO-3074 User Manual 16 Yo u can adjust the transm ission rate by the second switch of SW3. * T o increase the normal baud rates by eight times, (e.g. if we set the baud rate as 1 15.2K bps in softw are, then the actual hardware bau d rate will be increased to 921.6K bps), set switch 2 o f SW3 to “on”. T able 2.2: IRQ Setting via Switch 1 at SW ...

  • Microsoft UNO-3074 - page 27

    17 Chapter 2 2.3 .7 T ermination Resistor (JP6) The onboard te rmination resistor (120 ohm) fo r COM3/COM 4 can be used for long distance transmission or device matchin g (D efault Open). Close: Enable termination resistor . 2. 4 LAN: Ethernet Connector The UNO-3074 is equipped with a Realtek R TL8139C Eth ernet LAN co n- troller that is fully comp ...

  • Microsoft UNO-3074 - page 28

    UNO-3074 User Manual 18 2.5.2 Isolated Input s Each of isolated digital input channels accepts 0 ~ 50 VDC voltage inpu ts, and accepts bi-directional input. The voltage range is -3 ~ 3 V DC for logic 0 (low), -50 ~ -10 V DC and 10 ~ 50 VDC for lo gic 1 (high). It means that you can apply positive or negative volt age to an isolated input pin (V in) ...

  • Microsoft UNO-3074 - page 29

    19 Chapter 2 2.5.3 Interrupt Function of the DI Signals DI0 and DI1 can be used to generate hardware interrupts. Users can setup the configuration of them by programmi ng the interrup t control register . The channels are conne cted to the interrupt circuitry . Users can disable/ enable interrupt function, select trig ger type or latch the port dat ...

  • Microsoft UNO-3074 - page 30

    UNO-3074 User Manual 20 2.5.6 Interrupt En able Control Function The user can choose to enable or disable the interrupt fu ncti on by wri ting its correspon ding value to the interrupt disable/enable control bit in the interrup t control register , as shown in T able 2.6. 2.5.7 Interrupt T riggering Edge Control The interrupt can be trig gered by a ...

  • Microsoft UNO-3074 - page 31

    21 Chapter 2 2.6 Onboard Isolat ed Digit al Output The UNO-3074 has 4 isolat ed DO channels desi gnated DO0 ~ DO3. 2.6.1 Pin Assign ments The connector type of UNO-3074 is plug-in scr ew terminal block that enables you to conn ect to fiel d I/O devices direct ly without add itional accessories. Fi gure 2.6 and T able 2.9 show it s pin assignment as ...

  • Microsoft UNO-3074 - page 32

    UNO-3074 User Manual 22 2.6.2 Power On Confi gurat ion Default conf iguration after power on or hardware reset is to set all th e iso- lated digital output cha nnels to open status (the current of the load can ’ t be sink) so that users need not worry about damagi ng external devices during system startup or reset. When the system is hot res et, ...

  • Microsoft UNO-3074 - page 33

    23 Chapter 2 Figure 2.7: Isolated Digit al Output Connection Note: Please refer to App endix A.3 T able A.6 for comm and of DO Note: UNO- 3074 provides built-in examples to show how to deliver digital outpu t functionality . Refer to console mode examples in C:Program FilesAdvan- techUNOUNO_IsaDIOExam plesConsole. (Please install DI/O driver ...

  • Microsoft UNO-3074 - page 34

    UNO-3074 User Manual 24 2. 7 Onboard Isolated Counter/T i mer The UNO-3074 uses one 82C54 progr ammable timer/ counter chip that includes three indepen dent 16-bit down counters: counter 0, counter 1 and counter 2. Counter 0 and cou nter 1 are for users, and co unter 2 is specif ied for the system and can’ t be used by user . Each counter has clo ...

  • Microsoft UNO-3074 - page 35

    25 Chapter 2 CTR0F/CTR1F: (Counter 0/1) interrupt flag bit CTR0Gate/CTR1 Gate: (Counter 0/1) gate control bit CTR0Out /CTR1Ou t: (Counter 0/1) output statu s bit CTR0CLKSet /CTR1CLKSet: (Counter 0/ 1) clock source c ontrol bit CTR0GateSet/CTR1GateSet: (Counter 0/1 ) gate source c ontrol bit CTR0OutS et/ CTR1OutSet: ( Counter 0 /1) output destin ati ...

  • Microsoft UNO-3074 - page 36

    UNO-3074 User Manual 26 2.7.4 32-bit C ounter F unction Block (CTR32Se t=1) Figure 2.10: 32-bit Counte r Function Block 2.7.5 Counter Cl ock Source There are two clock sources available for the user c ounters by setting counter cl ock control bits - CTR0CLKSet and CTR1CLKSet. 2.7.6 Counter Internal Cloc k There are four frequency options to choose ...

  • Microsoft UNO-3074 - page 37

    27 Chapter 2 2.7.8 Coun ter Outp ut De stination Yo u can choose the outpu t destinatio n of counter 0 and counter 1 by sett ing “Output Destination control bits”- CTR 0OutS et and CTR1OutSet. 2.7.9 Coun ter Interr upt Flag The interrupt flag bit is a flag indicating the status of an interrupt. It is a readable/writable b it. T o find the statu ...

  • Microsoft UNO-3074 - page 38

    UNO-3074 User Manual 28 2.7.10 Cascade d 32-bit C ounter Y ou can also cascade counter 0 and counter 1 together as one 32-bit counter/ti mer , and it’ s configured by contro l bit - CTR32Set. 2. 8 P ower In put UNO-3074 comes with a Phoenix connect or that carries 16~36 VDC exter- nal power i nput, and features reversed wiring protecti on. Theref ...

  • Microsoft UNO-3074 - page 39

    29 Chapter 2 Y ou can see the LED indicators to moni tor power input situation. (Please refer to Figure 2.12 for location of LED). If the voltage of power input P1> 15 VDC, the P1 LED indicator will be enable (means the first power input is used). It is the same for P2 LED indicator (to show if the voltage of power input P2 > 15 VDC). When an ...

  • Microsoft UNO-3074 - page 40

    UNO-3074 User Manual 30 PWR =0, Power fail =1, Power normal P1 (24V) =0, Power input 1 fail =1, Power input 1 normal P2 (24V*) =0, Power input 2 fail =1, Power input 2 normal 2. 9 LED and Buzzer for System Diag nosis In a “headless application” (an application without a monitor display ), it is always diff icult to know the sys tem status. Anot ...

  • Microsoft UNO-3074 - page 41

    31 Chapter 2 LEDEn: =0, DIAG LED disable =1, DIAG LED enable LEDS0 and LEDS1: LE D flickering speed setting bit (refe r to T abl e 2.20) SPKEn: =0, Speaker disable =1, Speaker enable SPKS0 & SPKS1: Bu zzer alarming setting bit (refer to T able 2.21) T able 2.19: LED & Buzzer Control Register 210H R /W DIAG LED Register LEDS1 LEDS0 LEDEn 21 ...

  • Microsoft UNO-3074 - page 42

    UNO-3074 User Manual 32 PS/2 Keyboard and Mouse Connector The UNO-3074 provides a PS/2 keyboard and PS/ 2 mouse connector . A 6- pin mini-D IN connector is located on the front panel of the UNO-3074. UNO-3074 comes with an adapter in the accessory package (see sectio n 1.5) to convert from the 6-pin mini-DIN connector to two 6-pin mini- DIN connect ...

  • Microsoft UNO-3074 - page 43

    33 Chapter 2 For example, if you insert one PCMCIA IDE card, this card will appear in the IDE ATA/ATAPI controllers (as the figu re below). So please pay attention that the PCMCIA will appear in the difference place of device manager according to the type of PCMCIA. Please double click on the PCMCIA device. Note: Please don’t change the IR Q of P ...

  • Microsoft UNO-3074 - page 44

    UNO-3074 User Manual 34 Make sure th e IRQ of P CMCIA devi ce is 09. ...

  • Microsoft UNO-3074 - page 45

    35 Chapter 2 2. 12 VGA Disp lay Con nector The UNO-3074 provides a VGA control ler (Int el 852/855GME GMCH/ ICH4 Chipset 400 MHz PSB) for a high re solution VGA in terface. I t sup- ports CR T mode: 1280 x 1024 @ 32b pp (60Hz), 10 24 x 768 @ 32bpp (85Hz) and supports 8/16/32 MB frame buf fer with system memo ry . You can set the hot-key and other c ...

  • Microsoft UNO-3074 - page 46

    UNO-3074 User Manual 36 ...

  • Microsoft UNO-3074 - page 47

    37 Chapter 2 2. 13 Battery Backup SRAM UNO-3074 pro vides 512 KB of battery backup SRAM . This ensures that you have a safe place to store critical data. Y ou can now write software applications without being concer ned that system crashes will erase criti- cal data from the memory . There is a BTR Y LED in the front panel of the UNO-3074 ( Fi gu r ...

  • Microsoft UNO-3074 - page 48

    UNO-3074 User Manual 38 2.13.1 Lithium B attery S pecification Ty p e : BR2032 (U sing CR203 2 is NOT recomm ended) Output voltage: 3 V DC Location: Mainbo ard of UNO-3074. ( Figure 2.15) When the voltage of battery < 2.5 VDC, BTR Y LED w ill light up. Figure 2.15: Lithium Battery for SRAM 2. 14 Reset Button Press the "Reset" button to ...

  • Microsoft UNO-3074 - page 49

    CHAPTER 3 Initial Setup This chapter introduces how to initial ize the UNO-3074. Sections include: • Introduct ion • Inserting a CompactFlash Card • Chassis Grounding • Conn ecting Power • Connecting a Hard Disk • BIOS Setup and Sys tem Assignments ...

  • Microsoft UNO-3074 - page 50

    UNO-3074 User Manual 40 Chapter 3 Initial Setup 3. 1 Inserting a Comp actFlash Card UNO-3074 pro vides two CompactFlash slots. One slot (CN4) on the daughterbo ard is accessible from the front panel, wh ere you can insert your CompactF lash card directly . The other slot (CN3) is inside UNO- 3074 on its motherboard. Y ou can set JP1 and JP2 to deci ...

  • Microsoft UNO-3074 - page 51

    41 Chapter 3 3.3 Inst alling a Hard Disk The procedure for installin g a hard disk into the UNO-3074 is list ed below . Please follow these steps carefully . 1. Remove the power cord. 2. Unscrew the eight screws from the upper cover (as shown below) 3. Unscrew the HDD bracket from the upper cover . 4. Install the HDD in HDD bracket a n d secure wit ...

  • Microsoft UNO-3074 - page 52

    UNO-3074 User Manual 42 ...

  • Microsoft UNO-3074 - page 53

    43 Chapter 3 ...

  • Microsoft UNO-3074 - page 54

    UNO-3074 User Manual 44 ...

  • Microsoft UNO-3074 - page 55

    45 Chapter 3 5. Connect the IDE flat cable to Primary (recommen ded; CN1 of mainboard) or second ary IDE conn ector (CN2 of mainboard), then connect the other side of the connect or to the hard disk. (Refer to Figure 3.1 for the location of CN1 and CN2) Figure 3.1: IDE Connector (CN1 and CN2) 6. Re-fasten the upper cover with the eight screws. Note ...

  • Microsoft UNO-3074 - page 56

    UNO-3074 User Manual 46 3.4 Inst alling a PCI-b us Card The procedure for inst alling a PCI- bus card into the UNO-3074 is listed below . Please follow these steps carefully . 1. Remove the power cord. 2 .R e m o v e the upper cover of UNO-3074 . 3. Unscrew the screw of a PCI bracket, and remove it. 4. Plug-in PCI-bus card in a PCI-slot of UNO -307 ...

  • Microsoft UNO-3074 - page 57

    47 Chapter 3 Figure 3.3: 2nd PCI-bus Card Inst allation 7. Cut of f a part of the anti-vib ration rubber if it is too long to fit into the bo x when the PCI card is fixed. Figure 3.4: Adjust the Anti-V ibration Rubber 8. Screw back the upper cover with th e four screws. ...

  • Microsoft UNO-3074 - page 58

    UNO-3074 User Manual 48 3.5 Mounting UNO-3074 There are 3 types of mounting kits for UNO -3000 series: • Panel mount • Stand mount • W all mount Pls refer to UNO-3000 Series Accessories Manual 3.6 Inst alling Power Cable UNO-3074 pro vides an int ernal backup power sou rce so that it can pro- vide po wer for a CD-ROM, DVD-ROM or other externa ...

  • Microsoft UNO-3074 - page 59

    49 Chapter 3 3.7 UNO-3074 Mounting Caution Figure 3.6: UNO-3074 Im proper Installation (1) Figure 3.7: UNO-3074 Im proper Installation (2) ...

  • Microsoft UNO-3074 - page 60

    UNO-3074 User Manual 50 Figure 3.8: UNO-3074 Correct Installation Note: Because the heat tran sfer mechan ism is designe d close to the right side of system, make sure not to attach the right side of the UNO chassis to the wall or ground (shown in Figure 3.10 and 3.1 1). It may cause the system to hang. Instead, try to allow some sp ace on the righ ...

  • Microsoft UNO-3074 - page 61

    51 Chapter 3 3. 8 BIOS Setup and System Assignment s UNO-3074 adapt s Advantech’ s SOM-4486/4481 CPU module. Further informati on about the SOM-4486/4481 CPU module can b e found in us er manual of SOM-4486/4481. Y ou can find this manu al on the driver and utility CD of UNO-3074 in the accessory pack age. Please note that you can try to “LOAD ...

  • Microsoft UNO-3074 - page 62

    UNO-3074 User Manual 52 ...

  • Microsoft UNO-3074 - page 63

    APPENDIX A System Settings and Pin Assignment s ...

  • Microsoft UNO-3074 - page 64

    UNO-3074 User Manual 54 Appendix A System Settings and Pin Assignment s A.1 System I/O Address and Interrupt Assig nments T able A.1: UNO-3074 System I/O Port Address Range Device 000-01F DMA controller (slave) 020-03F Interrupt controller 1 (master) 040-05F 8254 timer/counter 060-06F 8042 (keyboard controll er) 070-07F Real-time clock, non-maskabl ...

  • Microsoft UNO-3074 - page 65

    55 Appendix A 3D0-3DF Color/graphics monitor adapte r 3F0-3F7 Diskette controller 3E8-3EF Serial p ort 3 3F8-3FF Serial port 1 443 W atchdog timer DC000-DFFFF Battery backup resource T able A.2: UNO-3074 Interrupt A ssignments Interrupt No. Interrup t Source IRQ 0 Interval timer IRQ 1 Key board IRQ 2 Interrupt from controller 2 (cascade) IRQ 3 COM2 ...

  • Microsoft UNO-3074 - page 66

    UNO-3074 User Manual 56 A. 2 Board Connectors and Jumpers There are severa l connectors and ju mpers on the UNO-3074 board. The following sections tell you how to configure the UNO-3074 hardware set- ting. Figures A.1 to A.5 show the location of the connectors and jumpers. Figure A.1: Backplane Connector & Jumpers Figure A.2: Mainboard Conn ect ...

  • Microsoft UNO-3074 - page 67

    57 Appendix A Figure A.3: Mainboard Connecto r & Jumpers (Front) ...

  • Microsoft UNO-3074 - page 68

    UNO-3074 User Manual 58 Figure A.4: Daughter Connector & Jumpers (Front) ...

  • Microsoft UNO-3074 - page 69

    59 Appendix A Figure A.5: Daughter Co nnector & Jumpers (Back) ...

  • Microsoft UNO-3074 - page 70

    UNO-3074 User Manual 60 T able A.3: Connector and Jumper Descriptions Location Label Function Backplane CN1 Phoenix power connector CN2 Internal power source (Reserved) CN3 D IO connector CN4 Communicati on slot fo r main board PICMG1 Communication slot for ma in board PCI 1 PCI slot 1 PCI 2 PCI slot 2 PCI 3 PCI slot 3 PCI 4 PCI slot 4 T able A.4: ...

  • Microsoft UNO-3074 - page 71

    61 Appendix A T able A.5: Connector & Jumper Descriptions Daughterboard CN1 PC card slot CN2 Communication slot for mainboard CN3 PS/2 keyboard and mouse connector CN4 CompactFlash slot 2 SW1 Reset butto n D1 COM1 Tx LED D2 W arning LED for battery backup SDRAM D3 COM1 Rx LED D4 COM2 Tx LED D5 COM2 Rx LED D6 COM3 Tx LED D7 COM3 Rx LED D8 COM4 T ...

  • Microsoft UNO-3074 - page 72

    UNO-3074 User Manual 62 A. 3 UNO-3074 Contro l Register * Refer to 82c54 manua l T able A.6: UNO-3074 Control Register Base Address 7 6 5 4 3 2 1 0 200H R Isolated Digital Input S tatus Register DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0 201H R/W Isolated Digital Output Control/S tatus Register DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0 202H R/W Interrupt Enable Control ...

  • Microsoft UNO-3074 - page 73

    63 Appendix A A. 4 RS-232 S t andard Serial Port (COM1~COM2) T able A.7: RS-232 Serial Port Pin Assigns Pin RS-232 Signal Name 1 DCD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9R I ...

  • Microsoft UNO-3074 - page 74

    UNO-3074 User Manual 64 A.5 RS-232/422/485 Se rial Port (COM3~COM4) A. 6 Ethernet RJ-45 Conn ector (LAN1~LAN2) T able A.8: RS-232/422/485 Serial Port Pin Assigns Pin RS-232 RS-422 RS-485 1 DCD Tx- DA T A- 2R x D T x + D A T A + 3 TxD Rx+ N C 4D T R R x - N C 5G N D G N D G N D 6 DSR NC NC 7 RTS NC NC 8 CTS NC NC 9R I N C N C T able A.9: Ethernet RJ ...

  • Microsoft UNO-3074 - page 75

    65 Appendix A A.7 Power Scre w T e rminal (PWR) Figure A.8: Power Connector Pin Assignment s T able A.10: Power Connector Pin Assignment s Pin Signal Name +Vs Po wer input 1; Range: 16~36 VDC (P1) +Vs* Po wer input 2; Range: 16~36 VDC (P2) GND Ground ...

  • Microsoft UNO-3074 - page 76

    UNO-3074 User Manual 66 A. 8 PS/2 Keyboard and Mouse Connector A.9 USB Connector (USB1~USB4) T able A.1 1: Keyboard & Mouse Connector Pin s Pin Signal Name 1 KB DA T A 2M S D A T A 3G N D 4V C C 5 KB Clock 6M S C l o c k T able A.12: USB Connector Pin Assign ment s Pin Signal Name Cable Color 1 VCC Red 2D A T A + W h i t e 3 DA T A- Green 4 GND ...

  • Microsoft UNO-3074 - page 77

    67 Appendix A A. 10 VGA Dis play Connector T able A.13: VGA Adapt or Cable Pin Assignmen Pin Signal Name 1R e d 2G r e e n 3B l u e 4N C 5G N D 6G N D 7G N D 8G N D 9N C 10 GND 11 N C 12 NC 13 H-SYNC 14 V -SYNC 15 NC ...

  • Microsoft UNO-3074 - page 78

    UNO-3074 User Manual 68 ...

  • Microsoft UNO-3074 - page 79

    APPENDIX B Programming the W atchdog T imer ...

  • Microsoft UNO-3074 - page 80

    UNO-3074 User Manual 70 Appendix B Programming the W atchdog Ti m e r Below are samples of code for contro lling the W atchdog Timer function. --------- ----------- ---------- ----------- ---------- ----------- ----------- ---------- Enter the extended function m ode, interruptible double-write | --------- ----------- ---------- ----------- ------- ...

Manufacturer Microsoft Category Webcam

Documents that we receive from a manufacturer of a Microsoft UNO-3074 can be divided into several groups. They are, among others:
- Microsoft technical drawings
- UNO-3074 manuals
- Microsoft product data sheets
- information booklets
- or energy labels Microsoft UNO-3074
All of them are important, but the most important information from the point of view of use of the device are in the user manual Microsoft UNO-3074.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Microsoft UNO-3074, service manual, brief instructions and user manuals Microsoft UNO-3074. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Microsoft UNO-3074.

Similar manuals

A complete manual for the device Microsoft UNO-3074, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Microsoft UNO-3074 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Microsoft UNO-3074.

A complete Microsoft manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Microsoft UNO-3074 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Microsoft UNO-3074, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Microsoft UNO-3074, that we can find in the current document
3. Tips how to use the basic functions of the device Microsoft UNO-3074 - which should help us in our first steps of using Microsoft UNO-3074
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Microsoft UNO-3074
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Microsoft UNO-3074 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Microsoft UNO-3074?

Use the form below

If you did not solve your problem by using a manual Microsoft UNO-3074, ask a question using the form below. If a user had a similar problem with Microsoft UNO-3074 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)