Manual CDA CI260

40 pages Not applicable
Download

Go to site of 40

Summary
  • CDA CI260 - page 1

    Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu CI260 freestanding washing machine Manual for Installation, Use and Maintenance ...

  • CDA CI260 - page 2

    2 ...

  • CDA CI260 - page 3

    3 Contents page page 4 Important page 6 Safety warnings page 7 W arning page 8 R ecommendations page 9 Before first use Page 11 Detergents and additives Page 12 Eco note L oading the washing machine Page 13 Control panel Page 14 Starting a wash programme Page 18 Wash programme phases and power cuts Page 19 Programme table Page 22 Care and maintena ...

  • CDA CI260 - page 4

    4 Important This appliance must only be used for the purpose for which it is intended, i.e. domestic use . Any other use could be dangerous and may lead to premature failure of the appliance. The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve t ...

  • CDA CI260 - page 5

    5 IMPORT ANT INFORMA TION FOR CORRECT DISPOS AL OF THE PRODUCT IN A CCORD ANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority dierentiated waste collection centre or to a dealer providing this service. Disposing of a household applian ...

  • CDA CI260 - page 6

    6 Safety warnings • If the plug or cord are damaged, do not connect the appliance to the mains power supply . If the cord is damaged it should be replaced by the manufacturer or appointed service agent in order to avoid a hazard. • T o remove the plug from the socket, pull on the body of the plug, not the cable. • Do not plug the appliance in ...

  • CDA CI260 - page 7

    7 W arnings T o avoid the risk of fire, electric shocks, injury or damage when using your washing machine, please take the following precautions: • Please read all the instructions before using the washing machine . • Do not wash items that have previously been cleaned, washed, soaked or treated with petrol, solvents for dry cleaning, other in ...

  • CDA CI260 - page 8

    8 R ecommendations • R esidues of detergent or softener left in the detergent drawer for long periods will dry and stick to the detergent drawer . T o prevent this put the detergent and softener into the detergent drawer just before washing. • It is recommended that the pre-wash programme should only be used for very dirty clothes. • Do not e ...

  • CDA CI260 - page 9

    9 Before first use When your washing machine has been correctly installed, we recommend that you pre-clean the machine. This is to check that the installation, the connections and the drainage are all correct, and to thoroughly clean the inside of the washing machine before any wash programmes are run. Prior to pre-cleaning you should ensure the t ...

  • CDA CI260 - page 10

    10 • R emove any metal pieces found on the items to be washed, for example curtain hooks. • Fasten all zips and buttons. • T urn garments, such as knitted fabrics, inside out. • Before placing the clothes in the drum, make sure all the pockets are empty . Any small objects may block the drain pump. • W e recommend loading the washing mach ...

  • CDA CI260 - page 11

    11 Detergents and additives Y our washing machine’ s detergent dispenser has three sections as shown in figure 1. Add the required amount of detergent and fabric softener into the specific sections of the detergent dispenser before starting the wash programme. The detergent dispenser is designed to allow the use of liquid detergents rather than ...

  • CDA CI260 - page 12

    12 Do not ex ceed the MAX level in the fabric softener section and ensure that concentrated fabric softeners are diluted before use for best washing results. R emember that the amount of detergent to be used will always depend on: • The amount of clothes to be washed. • How heavily the clothes are soiled. • The hardness of the water (Informat ...

  • CDA CI260 - page 13

    13 Control panel fig. 2 1. Mode button 2. Display 3. Mode selection button 4. W ash progress indicators 5. Start/pause button 6. Programme control knob 7 . Spin speed control knob 8. Extra function buttons 400 CI260 500 600 700 800 1000 1200 0 A mode ˚C select B C D E F G H I J K L 0 hold extra pre easy 60 ˚C 40 ˚C 1 2 3 4 5 6 7 8 ...

  • CDA CI260 - page 14

    14 S tarting a wash programme • T urn the programme control knob to the required programme • T urn the spin speed control knob to the required spin speed • Select any required extra functions, as detailed below • Select any required extra options, as detailed below • Press the Start/P ause button When a wash programme is in progress, the ...

  • CDA CI260 - page 15

    15 A programme without final spin is used to prevent creasing when washing special fabrics. Extra functions Extra functions can be selected once the programme has been set. T o select any extra function, press the required extra function button. The programme table on page 19 shows the functions available for each programme. If the function is ava ...

  • CDA CI260 - page 16

    16 Easy iron This function prevents garments from creasing ex cessively to make them easier to iron. Extra options Extra options can be selected once the programme has been set. The programme time shown on the display will reduce according to the extra functions selected. W ash temperature adjustment The temperature for each programme can be adjust ...

  • CDA CI260 - page 17

    17 T o set the delay timer: • Press the mode button twice. The display will show . • Press the select button repeatedly to cycle through the delay times available. • Once the required time delay is shown on the display , the washing machine will set after appro ximately three seconds ’ delay . K ey Lock The lock function ensures that the pr ...

  • CDA CI260 - page 18

    18 W ash programme phases and power cuts Programme Phases • The progress indicators will illuminate successively as the programme progresses. The time remaining until the end of the programme will also appear on the display . It updates at regular intervals, but not minute by minute. Power Cuts • If there is a power cut, when the electricity co ...

  • CDA CI260 - page 19

    19 W ash temperature options Preset (max) spin speed Pre W ash Easy Iron Rinse Hold Extra Rinse Index Programmes Cold 30 40 50 60 70 80 90 Speed Max On textile A Cotton 95°C / Antibacterial A A A A A A A P 1200 A A A A B Cotton 60°C PW A A A A P 1200 S A A A C Eco 60°C A A A A P 1200 A A A A D Cotton 40°C AA A A P 1200 A A A A E Hygiene 30°C A ...

  • CDA CI260 - page 20

    20 Index Programme Detergent Compart. Max. Dry Load Capacity (kg) Type of L aundry Explanations A Cotton 95°C 1 9 Dirty , high temperature resistant cotton and linen textiles. This programme can also be run empty as a cleaning cycle. Underwear , sheets, table cloths, t-shirts, shirts, towels (max 4kg) B Cotton 60°C prewash 1+3 9 V ery dirty cotto ...

  • CDA CI260 - page 21

    21 Index Programme Detergent Compart. Max. Dry Load Capacity (kg) Type of L aundry Explanations K Fast 60min 60°C 1 4 This programme will wash dirty cottons, coloureds and lined textiles in 60 minutes at 60°C Underwear , sheets, table cloths, t-shirts, shirts, towels L Super Rapid 12min 30°C 1 2 This programme will wash lightly soiled items in 1 ...

  • CDA CI260 - page 22

    22 Care and maintenance Before beginning any care or maintenance, you should always disconnect the appliance from the electricity supply , and also turn o the water supply . If a programme has been run recently , wait for the water in the appliance to cool down to prevent risk of scalding. W ater inlet lters There are filters on the tap side ...

  • CDA CI260 - page 23

    23 fig. 4 Pump lter The pump filter system prevents ingress of lint or foreign objects into the drain pump, reducing the risk of damage. The pump filter should be cleaned regularly , every two to three months at least. T o clean the lter: • Open the kickplate cover by pulling down on the groove at the top of the cover . • Place a conta ...

  • CDA CI260 - page 24

    24 fig. 5 Detergent drawer Detergents may cause residue build up in the detergent drawer and the drawer housing over time. The drawer should be cleaned regularly to remove these residues. T o remove the drawer: • Pull the drawer out until it stops. • T o remove the drawer , press down on the siphon lid inside the drawer and remove from the hou ...

  • CDA CI260 - page 25

    25 Cleaning the washing machine exterior The exterior of the washing machine should be cleaned with warm soapy water or a gentle cleaning agent. Do not use abrasive cleaning products or solvents. It should then be dried thoroughly with a soft cloth. Please note - wipe any detergent spills immediately to minimise the risk of damage to the washing ma ...

  • CDA CI260 - page 26

    26 Practical information Alcoholic beverages: The stain, should first be washed with cold water , than wiped with glycerine and water and be rinsed with water mix ed with vinegar . Shoe Polish: The stain should be slightly scratched without ruining the cloth, rubbed with detergent and rinsed. In case it is not eliminated, it should be rubbed with ...

  • CDA CI260 - page 27

    27 Practical information Blood stain: Lay your clothes in cold water for 30 minutes. If the stain still does not disappear , lay in mixture of water and ammonia (3 table-spoons of ammonia in 4 litres of water) for 30 minutes. Cream, ice-cream and milk: Lay your clothes in cold water and rub the stained area with detergent. If the stain has still no ...

  • CDA CI260 - page 28

    28 Installation T ransit bolts, located at the rear of the appliance, must be removed prior to using the appliance to prevent damage. • L oosen the transit bolts using a suitable spanner by turning them anti- clockwise and then remove them. • Cover the holes with the plastic plugs supplied. Do not throw the transit bolts away . If you need to m ...

  • CDA CI260 - page 29

    29 Levelling T o reduce the noise level from the washing machine and to prevent unnecessary movement during use, ensure the washing machine is level using the adjustable feet. First, fix and level the rear feet. When they are properly fix ed, secure the metal locknut tightly against the underside of the washing machine. • Put the washing machin ...

  • CDA CI260 - page 30

    30 Connecting to the mains water supply • Fit the seal included in the hose packing at the end of the water inlet hose on the tap side. • Connect the water inlet hose to a 3”/4, geared water tap. Then securely tighten the connecting nut by hand. • After connections are completed, check for the non-leakage of the connection joints by turning ...

  • CDA CI260 - page 31

    31 The drain hose must be securely fastened to the outlet to prevent any risk of the drain hose becoming detached and causing ooding. Once the appliance is connected to the water supply and the drain connection, ensure that the water inlet and drain hoses are not folded, twisted, crushed or elongated by stretching when moving the appliance into ...

  • CDA CI260 - page 32

    32 How to connect an alternative plug If the fitted plug is not suitable for your socket outlet, then it should be cut o and disposed of safely to prevent the risk of electric shock. A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used. As the colours of the wires in the mains lead of this appliance may not correspond ...

  • CDA CI260 - page 33

    33 Failure Probable failure The process to be done The door is not shut properly . Shut the door properly so that you hear the click. If the error persists, unplug the machine, close the water tap and contact CD A Customer Care. Inadequate water supply . Make sure the water tap is fully open and there is no fault with the water supply . Clean the i ...

  • CDA CI260 - page 34

    34 Fault Probable cause Methods of elimination The machine will not start. It is unplugged. Insert the plug into the socket. The fuse is damaged. Replace the fuse . There is a fault with the power supply . Check the power supply . Start/pause button has not been pressed. Press the start/pause button. The programme knob is in O (o ) status. Bring ...

  • CDA CI260 - page 35

    35 Fault Probable cause Methods of elimination Ex cessive foam in the detergent drawer . T oo much detergent has been used. Press the Start/P ause button. In order to stop the foam, dilute one tablespoon of softener in half a litre of water and pour it in the detergent drawer . W ait 5-10 minutes, then press the Start/P ause button. Ensure correct ...

  • CDA CI260 - page 36

    36 International washing signs W ash up to 90 °C W ash up to 60 °C Wash up to 30 °C Do not wash in a washing machine W ashing temparature Do not wash in a washing machine Lukewarm iron Medium hot iron Hot iron Do not iron Do not tumble dry Hang to dry Drip dry Dry flat Do not bleach Handy to bleach All of these are dry cleaning symbols. The let ...

  • CDA CI260 - page 37

    37 ...

  • CDA CI260 - page 38

    38 ...

  • CDA CI260 - page 39

    39 ...

  • CDA CI260 - page 40

    Please contact our Customer Care Department, or for Service on the details below . Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu ...

Manufacturer CDA Category Washing Machine

Documents that we receive from a manufacturer of a CDA CI260 can be divided into several groups. They are, among others:
- CDA technical drawings
- CI260 manuals
- CDA product data sheets
- information booklets
- or energy labels CDA CI260
All of them are important, but the most important information from the point of view of use of the device are in the user manual CDA CI260.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals CDA CI260, service manual, brief instructions and user manuals CDA CI260. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product CDA CI260.

Similar manuals

A complete manual for the device CDA CI260, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use CDA CI260 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of CDA CI260.

A complete CDA manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual CDA CI260 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the CDA CI260, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the CDA CI260, that we can find in the current document
3. Tips how to use the basic functions of the device CDA CI260 - which should help us in our first steps of using CDA CI260
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with CDA CI260
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of CDA CI260 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning CDA CI260?

Use the form below

If you did not solve your problem by using a manual CDA CI260, ask a question using the form below. If a user had a similar problem with CDA CI260 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)