English dropdown-ico

Manual Bunn 14

17 pages 3.63 mb
Download

Go to site of 17

Summary
  • Bunn 14 - page 1

    IMIX ® -14 INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic ...

  • Bunn 14 - page 2

    2 45304.1 050511 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years pa ...

  • Bunn 14 - page 3

    3 W ARNING • DO NO T O VERLOAD CIRCUIT . • AL W A YS ELECTRICALL Y GROUND THE CHASSIS. • DO NO T DEFORM PLUG OR CORD. • FOLLO W NA TIONAL AND LOCAL ELECTRICAL CODES. • KEEP COMBUSTIBLES A W A Y . F AILURE T O COMPL Y RISKS EQUIPMENT D AMA GE, FIRE OR SHOCK HAZARD . READ THE ENTIRE OPERA TING MANU AL BEFORE USING THIS PRODUCT 00986.0000F 1 ...

  • Bunn 14 - page 4

    4 INITIAL SET -UP 1. Apply the four non-skid pads from the parts box to the bottom of the legs. 2. Remove the drip tray assembly , drip tray bracket, and splash panel assembly from the parts box. 3. Place a set of key holes in the drip tray bracket over the lower two screws in the panel below the hopper ac- cess door; push down gently and tighten s ...

  • Bunn 14 - page 5

    5 DOOR COVER INST ALLA TION (Continued) 4. With door in raised position, remove four screws and remove inner access panel. Pull door inter - connect wiring through access hole. 5. Connect black four pin connectors. Connectors are keyed, and latch must engage hook. 6. Connect three pin connector to rear of the dis- play . 7. Connect six pin connecto ...

  • Bunn 14 - page 6

    6 ELECTRICAL REQUIREMENTS WARNING - If the power cord is ever damaged, it must be replaced by the manufacturer or its service agent with a special cord available from the manufacturer or its service agent in order to avoid a hazard. CAUTION - The dispenser must be disconnected from the power source until specified in Electrical Hook-Up. The 120 vo ...

  • Bunn 14 - page 7

    7 PLUMBING HOOK-UP 1. Flush the water line and securely attach it to the elbow fitting on the bottom of the dispenser . 2. T urn-on the water supply . This equipment must be installed to comply with the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA). For models insta ...

  • Bunn 14 - page 8

    8 INITIAL FILL & HEA T 1. T urn on the water supply and connect the dispenser to the power source. 2. W ater will automatically flow into the tank to the proper level and then shut-off. This will take less than ten minutes. 3. When the tank is full of water , open the front door and place the ON/OFF/NIGHT switch in the “ON” (upper) positio ...

  • Bunn 14 - page 9

    9 POWDER PRODUCT STRENGH ADJUSTMENT The strength of the individual powdered beverages can be adjusted by changing the hopper motor speed. See menus under “DRINK STRENGTH #” in the program menus to adjust the hopper dispense rate for each hop- per . DRAINING THE HOT W A TER T ANK CAUTION - The dispenser must be disconnected from the power source ...

  • Bunn 14 - page 10

    10 CLEANING The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all sur - faces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device. 44990.0000A 08/11 © 2011 BUNN-O-MA TIC CORPORA TION a. Wash b. Rinse c. Sanitize d. Dry a. Lave b. Enjuague c. Desinfecte d. Seque a b c d ...

  • Bunn 14 - page 11

    11 PROGRAMMING THE DISPENSER The following function screens are in order of appearance. Each screen will have instructions on how to ac- cess, and the procedures to program the various functions of the dispenser . T o enable programming, place the NORMAL/PROGRAM/RINSE” switch in the “PROGRAM” position. IMPORT ANT PROGRAMMING NOTES - READ CARE ...

  • Bunn 14 - page 12

    12 PROGRAMMING THE DISPENSER (Cont.) BEVERAGES The IMIX-14 unit has 15 dispense switches. PROGRAMMING SWITCHES Using the menu-driven display (T ouch Screen) on the front of the dispenser , the operator has the ability to alter or modify various functions of the dispenser . This allows for precise dispensing of various flavors of prod- ucts. Progra ...

  • Bunn 14 - page 13

    13 PROGRAMMING THE DISPENSER (Cont.) GLOSSARY Put "NORMAL/PROGRAM/RINSE" switch into "PROGRAM" position to access program menus. Adjust tank temperature (190° F maximum) Adjust minimum tank ready temper - ature for lockout (185° maximum) Adjust hopper motor speed for hopper 1. ## indicates hopper rpm T ANK TEMP ###° (-) EXIT ...

  • Bunn 14 - page 14

    14 PROGRAMMING THE DISPENSER (Cont.) T ANK TEMP ###° READY TEMP ###° (-) EXIT (+) DRINK STRENGTH 1 (-) EXIT (+) (-) ### (+) ENTER P ASSWORD (-) 0 (+) CALIBRA TION ? EXIT YES LOCKS/DISABLES ? EXIT YES AUDIBLE ALARM ? NO EXIT YES ENTER ASSET # ? EXIT YES ENABLE SERVICE # NO EXIT YES DIAGNOSTICS ? EXIT YES F ACTORY DEF AUL TS NO YES (A) continue to ...

  • Bunn 14 - page 15

    15 PROGRAMMING THE DISPENSER (Cont.) SELECT UNITS ENG EXIT METRIC ###° CAL ###° TEST POWDER 1? PRESS DISPENSE (A) Return to (B) (-) T ANK TEMP (+) 0 REFILL 155 (-) EXIT (+) TEST WA TER 1? PRESS DISPENSE TEST POWDER 2? PRESS DISPENSE TEST WA TER 2? PRESS DISPENSE TEST POWDER 3? PRESS DISPENSE TEST WA TER 3? PRESS DISPENSE TEST POWDER 4? PRESS DISP ...

  • Bunn 14 - page 16

    16 PROGRAMMING THE DISPENSER (Cont.) (C) (E) Return to (D) Return to (F) DISPENSE LOCKOUT NO EXIT YES RINSE ALARM ? NO EXIT YES RINSE ALARM TIME (-) ##HOURS (+) RINSE LOCKOUT NO EXIT YES SET P ASSWORD ? (-) 0 (+) TEST SWITCHES Use Switch T o T est TEST HEA TER ? EXIT YES TEST HOT WA TER ? EXIT YES TEST REFILL ? EXIT YES TEST AUGERS ? DISPENSE TO TE ...

  • Bunn 14 - page 17

    17 1 5 10 1 5 1 1 1 5 1 1 5 1 1 5 1 1 5 1 5 1 5 1 10 1 5 1 15 1 1 5 10 15 5 1 4 1 3 1 10 5 1 1 5 1 1 1 3 5 1 5 1 20 22 1 3 1 9 5 1 M SOL SOL SOL SOL SOL SOL SOL SOL REFILL VAL VE DISPENSE VA VLE #1 DISPENSE VA VLE #2 DISPENSE VA VLE #3 DISPENSE VA VLE #4 WHIPPER MTR #1 WHIPPER MTR #2 WHIPPER MTR #3 GRY GRY BRN/BLK RED ORN BLU BLK BRN/WHI WHI/ORG WH ...

Manufacturer Bunn Category Coffee Grinder

Documents that we receive from a manufacturer of a Bunn 14 can be divided into several groups. They are, among others:
- Bunn technical drawings
- 14 manuals
- Bunn product data sheets
- information booklets
- or energy labels Bunn 14
All of them are important, but the most important information from the point of view of use of the device are in the user manual Bunn 14.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Bunn 14, service manual, brief instructions and user manuals Bunn 14. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Bunn 14.

Similar manuals

A complete manual for the device Bunn 14, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Bunn 14 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Bunn 14.

A complete Bunn manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Bunn 14 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Bunn 14, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Bunn 14, that we can find in the current document
3. Tips how to use the basic functions of the device Bunn 14 - which should help us in our first steps of using Bunn 14
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Bunn 14
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Bunn 14 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Bunn 14?

Use the form below

If you did not solve your problem by using a manual Bunn 14, ask a question using the form below. If a user had a similar problem with Bunn 14 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)