Manual Craftsman 706.59669

18 pages 1.05 mb
Download

Go to site of 18

Summary
  • Craftsman 706.59669 - page 1

    706.596680 706.596690 6-Drawer Chest 7-Drawer Roll-A-Way Owners Manual Craftsman 7-Drawer AXS TM Roll-Away Craftsman 6-Drawer AXS TM Chest Section 1612 1613 1614 1615 1616 1617 1618 1623 1624 1625 Description Chest Top and Facia Drawer and Work Surface Bottom Replacement Top, Wiring Harness, Harness Grommet Chest Top without Task Light Task Light R ...

  • Craftsman 706.59669 - page 2

    i CRAFTSMAN°i CHEST TOP AND FACIA PARTS REPLACEMENT S Facia Chest Top with light Information Center CHEST TOP INSTALLATION AND REMOVAL (With task light) Tools Required: 3/8" Wrench Chest Top Removal • Disconnect power from unit. • Remove enough drawers to reach the top back inside of the unit. (See Drawer installation and removal.) • Pu ...

  • Craftsman 706.59669 - page 3

    INFORMATION CENTER INSTALLATION AND REMOVAL Tools Required: Screwdriver, Crosstip Tape Removal • Disconnect power from the unit. • Remove enough drawers to reach the retaining screw under the information center. (See removing and installing drawers.) • Loosen (do not remove) the retaining screw under the information center. • Pull the infor ...

  • Craftsman 706.59669 - page 4

    CONNECTING POWER • Ensure that the unit and power cord are clean and dry. • insert the round end of the power cord connector into the jack in the back of the unit. • Plug the cord into an appropriate electrical outlet. Fuse block Jack Cord REMOVING AND INSTALLING DRAWERS: • Empty the drawer. • Fully extend the drawer. Release Lever Style ...

  • Craftsman 706.59669 - page 5

    I CRAFTSMAN°I DRAWER AND WORK SURFACE PARTS REPLACEMENT SLIDE REPLACEMENT Tools Required: Drill 5/32" Drill bit Rivet gun Removal • Remove drawer or work surface from unit. (See drawer and work surface installation and removal.) • Carefully drill out rivet holding slide drawer member to drawer or work surface. • Rotate front of slide dr ...

  • Craftsman 706.59669 - page 6

    DRAWER AND WORK SURFACE REPLACEMENT DRAWER FRONT INSTALLATION AND REMOVAL Tools Required: Drill 5/32" Drill bit Rivet gun Crosstip screwdriver Removal • Remove drawer or work surface from unit. (See Drawer and Work surface installation and removal.) • Carefully drill out rivets holding slides to drawer. • Rotate front of slide down and o ...

  • Craftsman 706.59669 - page 7

    DRAWER AND WORK SURFACE INSTALLATION AND REMOVAL Note: For pull out work surface without task light, follow drawer removal instructions. DRAWER • Empty the drawer. • Fully extend the drawer. Release Lever Style - Lift or lower (depending on the slide) the release lever on both sides, (this allows the slides to ride over the stops.) Pull out to ...

  • Craftsman 706.59669 - page 8

    I CRAFTSMAN°I BOTTOM REPLACEMENT Tools Required: Socket Wrench 5/16" Socket Removal • Disconnect power from the unit. • Remove contents from drawers. • Carefully lay the chest on its back. Take care to prevent scratches or damage to the unit. • Remove (5) screws holding bottom on unit. • Remove bottom from unit. • Remove counterwe ...

  • Craftsman 706.59669 - page 9

    I CRAFTSMAN°I TOP, WIRING HARNESS, HARNESS GROMMET Parts Replacement Roll-away top WIRING HARNESS REPLACEMENT HARNESS GROMMET REPLACEMENT Tools Required: 3/8" Wrench WIRING HARNESS AND HARNESS GROMMET REMOVAL • Disconnect power from unit. • Remove pull out work surface and enough drawers to reach the top back inside of the unit. (See draw ...

  • Craftsman 706.59669 - page 10

    TOP INSTALLATION AND REMOVAL Tools Required: Screwdriver, Crosstip Roll-away top removal • Disconnect power from unit. • Remove pull out work surface. (See drawer and work surface installation and removal.) • Remove enough drawers to reach the top back inside of the unit. (See Drawer and Work surface installation and removal.) • Remove lock ...

  • Craftsman 706.59669 - page 11

    I CRAFTSMAN°I CHEST TOP WITHOUT TASK LIGHT Tools Required: Screwdriver, Crosstip Chest top removal • Disconnect power from unit. • Remove pull out work surface. (See drawer installation and removal.) • Remove enough drawers to reach the top back inside of the unit. (See Drawer installation and removal.) • Remove lock retaining clip. Pull l ...

  • Craftsman 706.59669 - page 12

    I CRAFTSMAN°I TASK LIGHT REPLACEMENT Tools Required: Screwdriver, Crosstip Removal • Disconnect power from the unit. • Fully extend task light assembly. • Make note of light orientation. • Remove (6) mounting screws to remove light. • Unplug light. Installation • Plug in new light. • Position new light in unit in same orientation as ...

  • Craftsman 706.59669 - page 13

    I CRAFTSMAN°I LOCKING SYSTEM Parts Replacement Actuator Channel Actuator Rod Bracket ACTUATOR ROD AND ACTUATOR CHANNEL REPLACEMENT ACTUATOR ROD AND ACTUATOR CHANNEL REMOVAL • Disconnect power from the unit. • Remove work surface (Roll-away only). • Remove pull out work surface (Roll- away only.) See drawer and work surface installation and r ...

  • Craftsman 706.59669 - page 14

    ACTUATOR ROD BRACKET INSTALLATION AND REMOVAL Removal • Disconnect power from unit. • For roll-aways, remove work surface. (See drawer and work surface installation and removal. • Remove enough drawers to reach the top back inside of the unit. (See Drawer and Work surface installation and removal.) • Remove top from unit. (See top installat ...

  • Craftsman 706.59669 - page 15

    CHEST TOP INSTALLATION AND REMOVAL (With task light) Tools Required: 3/8" Wrench Chest Top Removal • Disconnect power from unit. • Remove enough drawers to reach the top back inside of the unit. (See Drawer installation and removal.) • Push actuator rod to back of unit to disconnect from back of lock. Move actuator rod for access. • Re ...

  • Craftsman 706.59669 - page 16

    I CRAFTSMAN°I LOCK REPLACEMENT Removal • Disconnect power from unit. • For roll-aways, remove work surface. (See drawer and work surface installation and removal • Remove enough drawers to reach the lock retaining clip behind the lock. • Remove lock retaining clip. Pull lock out to remove. Installation • Position lock in unit. Install re ...

  • Craftsman 706.59669 - page 17

    I CRRFT.TMRN°J STRIKER REPLACEMENT Tools Required: Screwdriver Removal • Remove drawer from unit. • Turn drawer upside down. • Depress (2) detents. Push striker in to remove. Depress detents Drawer installation and removal • Emptythe drawer. • Fully extend the drawer. Release Installation • Turn drawer right side up. • Position strik ...

  • Craftsman 706.59669 - page 18

    I CRAFTSMAN°I DRAWER FRONT REPLACEMENT Tools Required: Crosstip screwdriver Removal • Remove retaining screw(s). • Slide drawer front assembly as indicated to unhook mounting tabs. • Pull out to remove. Installation • Position drawer front on drawer assembly. • Insert mounting tabs into notches on drawer. • Slide drawer front over to a ...

Manufacturer Craftsman Category Tool Storage

Documents that we receive from a manufacturer of a Craftsman 706.59669 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 706.59669 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 706.59669
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 706.59669.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 706.59669, service manual, brief instructions and user manuals Craftsman 706.59669. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 706.59669.

A complete manual for the device Craftsman 706.59669, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 706.59669 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 706.59669.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 706.59669 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 706.59669, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 706.59669, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 706.59669 - which should help us in our first steps of using Craftsman 706.59669
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 706.59669
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 706.59669 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 706.59669?

Use the form below

If you did not solve your problem by using a manual Craftsman 706.59669, ask a question using the form below. If a user had a similar problem with Craftsman 706.59669 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)