English dropdown-ico

Manual Makita HK1820

17 pages 4.61 mb
Download

Go to site of 17

Summary
  • Makita HK1820 - page 1

    PR ODUCT P 1/17 T ECHNICAL INFORMA TION Dimensions: mm (") W idth (W) Height (H) Length (L) 351 (13-3/4) 102 (4) 203 (8) L H W Continuous Rating (W) V oltage (V) Cycle (Hz) Input Output Max. Output (W) 110 120 220 230 240 5.3 5.0 2.6 2.5 2.4 50/60 50/60 50/60 50/60 50/60 550 --- 550 550 550 260 260 260 260 260 390 390 390 390 390 Models No. De ...

  • Makita HK1820 - page 2

    P 2 /1 7 [2] LUBRICATION Apply the following lubricants to protect parts and product from unusual abrasion: *Makita grease N.No.1 to the portions designated with black triangle *Makita grease R.No.00 to the portions designated with gray triangle *Makita grease N.No.2 to the portions designated with white triangle [1] NECESSARY REPAIRING TOOLS CAUTI ...

  • Makita HK1820 - page 3

    Motor housing P 3 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -1. Chuck Section R epair DISASSEMBLY DISASSEMBL Y M5x20 Pan head screw (2 pcs) Handle section Cap 38 Do the reverse of the disassembling steps. 2) Remove Cap 38 with slotted screwdriver. 4) Remove Chuck cover and Compression spring 42. Steel ball guide 1) For easy repairing, separate Handle secti ...

  • Makita HK1820 - page 4

    Remove Barrel cover support and Barrel cover. P 4 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -2. Barrel, Tool Holder, Cylinder Section R epair DISASSEMBLY 1) Disassemble the Chuck section as described in Figs. 2 , 3 . 2) Disassemble Tool holder, Ring 25 and Cylinder section from Barrel as described in Figs. 4 , 5 , 6 . Crank housing cover Ring spring 43 M4x ...

  • Makita HK1820 - page 5

    P 5 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -2. Barrel, Tool Holder, Cylinder Section R epair DISASSEMBLY Ring 39 1. Pull out Striker from Cylinder section. 2. Remove ring 25, Urethane ring 26 and Ring spring 37 from Cylinder. 3. By removing Ring 39, you can see Pin 6 (3 pcs) that join Tool holder with Cylinder. Ring 25 Urethane ring 26 Ring spring 37 Ro ...

  • Makita HK1820 - page 6

    P 6 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -2. Barrel, Tool Holder, Cylinder Section R epair ASSEMBLY Fig. 9 Do the reverse of the disassembling steps. Note: Rubber ring 13 is directional when assembled to Impact bolt. Be sure to assemble as illustrated to left in Fig. 9 . ASSEMBLY Do the reverse of the disassembling steps. DISASSEMBL Y [3] -3. Electric ...

  • Makita HK1820 - page 7

    P 7 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -4. Motor Section R epair 1) Disassemble Handle section as illustrated in Fig. 2 2) Separate the contact of Carbon brushes from Commutator as described in Fig. 11 . 3) Disassemble Crank housing complete from Motor housing as illustrated in Fig. 12 . 4) Remov e Piston from Crank shaft as illustrated in Fig. 13 . ...

  • Makita HK1820 - page 8

    P 8 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -4. Motor Section R epair 5) Remov e Crank section from Crank housing complete by tapping Crank housing complete with plastic hammer . ( Fig. 14 ) 6) Remov e Armature from crank housing complete using 1R023, 1R225 and arbor press as described in Fig. 15 . DISASSEMBL Y 1. Set Crank housing complete on 1R023, and ...

  • Makita HK1820 - page 9

    P 9 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -5. Gear (Crank) Section R epair DISASSEMBL Y Fig. 16 ASSEMBL Y Do the rev erse of the disassembling steps. Note: Make sure that O Ring 39 is mounted to Bearing box of Crank section before assembling Crank section to Crank housing complete. (Fig. 14 ) 1) Disassemble Gear (Crank) section from Crank housing compl ...

  • Makita HK1820 - page 10

    P 1 0 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -6. Handle Section R epair DISASSEMBL Y M5x20 Pan head scre w (2 pcs) 5x25 T apping scre w (2 pcs) Handle section Handle section consists of the follo wing main parts: Handle base, Handle, Handle cover And it can be disassembled as illustrated in Figs. 17 - 20 . Handle base Handle Lock-on button Stop ring E-4 ...

  • Makita HK1820 - page 11

    P 1 1 /1 7 [3] DISASSEMBLY/ASSEMBLY [3] -7. Recommended F astening T orque of Scr ews and Bolts R epair T ighten the bolt to the recommended torque described in Fig. 21 . Fig. 21 Fig. 22 [4] MAINTENANCE PR OGRAM When replacing carbon brush, it is recommended to do the follo wing maintenance at the same time for longer service life of the machine. 1 ...

  • Makita HK1820 - page 12

    P 1 2 /1 7 C ircuit diagram White Red Orange Blue Brown Color index of lead wires' sheath Black Clear Fig. D-1A Connector housing A Polyolefin tube (Protecti ve tube) Connector housing B Switch Connector Power supply cord Controller High V oltage Areas wher e Radio Interference Suppression Is Requir ed Fig. D-1B Fig. D-1C Low V oltage Areas wh ...

  • Makita HK1820 - page 13

    W iring diagram P 1 3 /1 7 Handle base, viewed from Controller side Handle Through hole for passing Lead wires from Controller and Connector housing to the opposite side Handle cov er Handle, vie wed from Handle cover side Handle base Controller Be careful not to pinch the Lead wires with the ribs. ( Figs. D-2, D-3 ) [1] Routing Wires Through Handl ...

  • Makita HK1820 - page 14

    W iring diagram P 1 4 /1 7 Fig. D-4A Fig. D-5A Handle base, vie wed from Controller side Handle base, viewed from Handle side Handle, viewed from Handle co ver side red blue Lead wires cov ered with Polyolefin tube (black) Controller Connector housing A Connector housing B Choke coil Controller Noise suppressor Switch Switch holder Pass the follo w ...

  • Makita HK1820 - page 15

    W iring diagram P 1 5 /1 7 Fig. D-4B Fig. D-5B [2] Wiring in Handle Base and Handle Low V oltage Areas wher e Radio Interference Suppr ession Is Required The Lead wires to Connector housing A must be tight between Controller and Lead wire holder . T erminal of Grounding wire Grounding wire (clear) Controller Put the slack portion of Lead wires in t ...

  • Makita HK1820 - page 16

    W iring diagram P 1 6 /1 7 Fig. D-4C Fig. D-5C [2] Wiring in Handle Base and Handle Other Areas where Radio Interfer ence Suppression Is Not Requir ed Put the slack portion of Lead wires in this space. Route all of the Lead wires to Switch through between the boss and the rib . Fix all of the Lead wires to Switch with this Lead wire holder of Switc ...

  • Makita HK1820 - page 17

    W iring diagram P 1 7 /1 7 Fig. D-6 [3] Connecting Connector Housing with Brush Holder Unit Rear cov er The side where Lead wires are drawn out must be placed on Rear co ver side as illustrated blow . to Controller on Handle base Connector housing A Connector housing B (if used) Motor housing Choke coil (if used) Connector housing is directional wh ...

Manufacturer Makita Category Mobility Scooter

Documents that we receive from a manufacturer of a Makita HK1820 can be divided into several groups. They are, among others:
- Makita technical drawings
- HK1820 manuals
- Makita product data sheets
- information booklets
- or energy labels Makita HK1820
All of them are important, but the most important information from the point of view of use of the device are in the user manual Makita HK1820.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Makita HK1820, service manual, brief instructions and user manuals Makita HK1820. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Makita HK1820.

Similar manuals

A complete manual for the device Makita HK1820, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Makita HK1820 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Makita HK1820.

A complete Makita manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Makita HK1820 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Makita HK1820, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Makita HK1820, that we can find in the current document
3. Tips how to use the basic functions of the device Makita HK1820 - which should help us in our first steps of using Makita HK1820
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Makita HK1820
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Makita HK1820 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Makita HK1820?

Use the form below

If you did not solve your problem by using a manual Makita HK1820, ask a question using the form below. If a user had a similar problem with Makita HK1820 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)