Manual Lucent Technologies TM-4500

20 pages 0.27 mb
Download

Go to site of 20

Summary
  • Lucent Technologies TM-4500 - page 1

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 1 45" Wood Burning Fireplaces P/N 850,045M REV. N/C 01/2007 TM-4500 MODEL RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE WH Report No. J20054576-231 This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system. Please read and under- s ...

  • Lucent Technologies TM-4500 - page 2

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 2 TABLE OF CONTENTS Safety Rules .................................... page 2 Tools and Building Supplies ............ page 2 Precautions ..................................... page 3 Introduction ..................................... page 3 Chimney/Mantel Clearances and Height Requirements ........... ...

  • Lucent Technologies TM-4500 - page 3

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 3 Figure 1 TYPICAL INSTALLATION *Construction Materials: • framing materials • paneling • particle board • flooring • dry wall • etc. • plywood PRECAUTIONS Note: These fireplace systems are not difficult to install. However, in the interest of safety, it is recommended that the installe ...

  • Lucent Technologies TM-4500 - page 4

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 4 Figure 2 LOCATION OF FIREPLACE Carefully select the proper location for heat circulation, aesthetics, chimney obstructions and clearance to side wall(s). With proper pre- planning, a slight adjustment of a few inches can save considerable time and expense later during construction and assembly. Cha ...

  • Lucent Technologies TM-4500 - page 5

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 5 DO NOT permanently place furniture or other items such as decorative pillows within 60" of the fireplace front face. ASSEMBLY STEPS Note: The following steps represent the normal sequence of installation. Each installation is unique, however, and might require a different sequence. 1. Position ...

  • Lucent Technologies TM-4500 - page 6

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 6 Step 3. Refer to fireplace drawings and specifi- cations on pages 6 and 7 for framing dimensions and details. Frame appliance enclosure as illus- trated in Figures 12 through 15 on page 7. IMPORTANT: UNDER NO CIRCUMSTANCES CAN THE FIREPLACE TOP SPACERS ( SEE FIGURE 11 ) BE REMOVED OR MODIFIED, NOR ...

  • Lucent Technologies TM-4500 - page 7

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 7 Note: The framed depth, 28 ¹ ⁵ ⁄ ₁ ₆ " (735 mm) from a framed wall, must always be measured from a finished surface. If a wall covering such as drywall is to be attached to the rear wall, then the framed depth must be measured from the drywall sur- face. It is important that this dime ...

  • Lucent Technologies TM-4500 - page 8

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 8 Step 5. Fireplace should be secured to side framing members using the full length nailing tabs at the top and bottom of the fireplace front face. Use 8d nails or equivalent ( Figure 18 ). Figure 18 Note: The nailing tabs and the area directly behind the nailing tabs are exempt from the clearances d ...

  • Lucent Technologies TM-4500 - page 9

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 9 Step 4. Note: Chimney sections are constructed with a unique locking tab design, which en- sures an immediate, tight assembly between sections. Plan your chimney requirements care- fully before assembly as chimney is difficult to disassemble after installation. If disassembled, the tabs might becom ...

  • Lucent Technologies TM-4500 - page 10

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 10 Locking Band Waterproof Caulk Roof Ridge 120 ° Step 8. The standard Security Chimneys FTF10 roof flashing assemblies include a storm collar. Slide the storm collar over outer chimney, rest on flashing spacers and align with top surface of flashing. Insert tab in slot, pull tight and bend tab back ...

  • Lucent Technologies TM-4500 - page 11

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 11 MULTIPLE TERMINATIONS If more than one termination is located in the same chase or within the same general proxim- ity, we suggest they should be separated in distance at least 24" (610 mm) horizontally from flue center to flue center and stacked or staggered vertically at least 18" (457 ...

  • Lucent Technologies TM-4500 - page 12

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 12 Figure 38 Figure 40 OFFSET CALCULATIONS Step 1. Use Offset Chart to determine amount of horizontal offset (A) and height (B) for various chimney section assemblies. Step 2. Use “Height of Chimney Only” column in The Vertical Elevation Chart to determine combinations of chimney used above retur ...

  • Lucent Technologies TM-4500 - page 13

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 13 397 ¹⁄₄ 33 1 ¹⁄₄ 20 1 1 403 ¹⁄₄ 33 7 ¹⁄₄ 11 1 1 411 34 3 0 0 12 421 ¹⁄₄ 35 1 ¹⁄₄ 10 1 2 427 ¹⁄₄ 35 7 ¹⁄₄ 01 1 2 431 ¹⁄₂ 35 11 ¹⁄₂ 20 1 2 437 ¹⁄₂ 36 5 ¹⁄₂ 11 1 2 445 ¹⁄₄ 37 1 ¹⁄₄ 00 1 3 455 ¹⁄₂ 37 11 ¹⁄₂ 10 1 3 461 ¹? ...

  • Lucent Technologies TM-4500 - page 14

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 14 Return Elbow Figure 41 Note: The return elbow assembly performs the same function as a stabilizer. Consider this when determining the need for a stabilizer. Note: Do not apply excessive pressure to any subsequent chimney section following return elbow assembly when installing. Ensure that each sub ...

  • Lucent Technologies TM-4500 - page 15

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 15 Outside combustion air ducting may be run upwards or vertically through framing and ceil- ing joists, with the hood installed through an outside wall and 3' (914 mm) below the termi- nation. Ducting may also be run downward through floor joists and under the home to a ventilated crawlspace no ...

  • Lucent Technologies TM-4500 - page 16

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 16 Figure 46 Note: Only non-combustible wall finishing materials are allowed on the front top of the unit, from the top edge of spacers down. See Figures 45 and 46 . Hearth Extensions and Wall Shields A hearth extension must be installed with all fireplaces. It is to protect the combustible floor in ...

  • Lucent Technologies TM-4500 - page 17

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 17 Answer - The minimum required thickness of the Micore 160 is .417”, therefore round up to nearest standard thickness available which is 1/2”. ** If the hearth extension material(s) that is intended to be used is NOT listed on Table 1, the material can still be used if the material(s) is noncom ...

  • Lucent Technologies TM-4500 - page 18

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 18 Locking Band 63L60 FLB Figure 50 Figure 49 FINISH TO YOUR TASTE There are a wide variety of “finished looks” for these fireplaces, from formal wall decor with elaborate mantels to rustic wood paneling or warm brick facings. Only noncombustible materials like stone, tile, brick, etc., may overl ...

  • Lucent Technologies TM-4500 - page 19

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 19 63L16 FTF10-12 63L17 FTF10-18 63L18 FTF10-36 62L94 FTF10-18C Chimney Section 62L95 FTF10-36C Storm Collar 63L59 FSC 63L40 F10F6 Flashing 63L41 F10F12 Firestop Spacer (Flat) 63L36 F10FS-2 Chase Termination (Square) 63L52 FTF10-CT2RS INSTALLATION COMPONENTS Firestop Spacer (30 ° ) 63L37 F10FS30-2 R ...

  • Lucent Technologies TM-4500 - page 20

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 20 The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. Printed in U.S.A. © 2007 by Lennox Hearth Products P/N ...

Manufacturer Lucent Technologies Category Indoor Fireplace

Documents that we receive from a manufacturer of a Lucent Technologies TM-4500 can be divided into several groups. They are, among others:
- Lucent Technologies technical drawings
- TM-4500 manuals
- Lucent Technologies product data sheets
- information booklets
- or energy labels Lucent Technologies TM-4500
All of them are important, but the most important information from the point of view of use of the device are in the user manual Lucent Technologies TM-4500.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Lucent Technologies TM-4500, service manual, brief instructions and user manuals Lucent Technologies TM-4500. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Lucent Technologies TM-4500.

A complete manual for the device Lucent Technologies TM-4500, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Lucent Technologies TM-4500 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Lucent Technologies TM-4500.

A complete Lucent Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Lucent Technologies TM-4500 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Lucent Technologies TM-4500, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Lucent Technologies TM-4500, that we can find in the current document
3. Tips how to use the basic functions of the device Lucent Technologies TM-4500 - which should help us in our first steps of using Lucent Technologies TM-4500
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Lucent Technologies TM-4500
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Lucent Technologies TM-4500 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Lucent Technologies TM-4500?

Use the form below

If you did not solve your problem by using a manual Lucent Technologies TM-4500, ask a question using the form below. If a user had a similar problem with Lucent Technologies TM-4500 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)