English dropdown-ico

Manual QSC DCM 10

24 pages 1.91 mb
Download

Go to site of 24

Summary
  • QSC DCM 10 - page 1

    DCM Series Digital Cinema Monito r & Crossover Sy stem User Manual DCM 10 DCM 10D DCM 30 DCM 30D *TD-000265-00* TD-000265-00-A ...

  • QSC DCM 10 - page 2

    Important Safety Instructions & Explanation of symbols 1- Read these in structions . 2- Keep these in structions . 3- Heed all warnings. 4- Follow all instructions. 5- Do not use this app aratus near water . 6- Clean only with a dry cloth . 7- Do not block any ventilation opening s. Install in accordance with QSC Audi o Product’ s instruction ...

  • QSC DCM 10 - page 3

    FEDERAL COMMUNICA TIONS COMMISSION (FCC) INFORMA TION NOTE: This equip ment has been tested and found to comply with th e limits for a class B digital d evice, pursuant to part 15 of the FCC rules. These limits are desig ned to provide re asonable pr otection against harmf ul interference in a residential installation . This equi pmen t generates, ...

  • QSC DCM 10 - page 4

    Introduction Thank you and co ngratulati ons on your purc hase of the QSC DCM Digit al Cin- ema Monitor . This product repres ents the sta te-of-the -art for cine ma-based signal pr ocessing an d monito ring funct ions in a sin gle, integr ated syst em. Designed to compliment QSC’ s DCA (Digit al Cinema Amplifier) Series and DCS (Digital Cine ma ...

  • QSC DCM 10 - page 5

    Sy stem Concepts Installer Features: •Provides Moni tor and Cr ossover f unctions in one box. •Minimizes th e amount of cabling required . Only 1 cable per am plifier channel pair . •Minimizes setup time, particularly in megaplex s with similar ro oms. •Provides l oudspeaker setting data base for most common th eater lou dspeaker br ands an ...

  • QSC DCM 10 - page 6

    1- Power switch 2- Monitor output loudspeaker 3- Power “o n” and diagnostic s indica tor LEDs 4- Monitor source s elector bu ttons 5- Amplifier/Processor selector button 6- Monitor output test points 7- Bypass switch and indicator L ED 8- Monitor vo lume co ntrol 9. Alternate EQ Select- Co nnecting this ter minal to ground with an external swit ...

  • QSC DCM 10 - page 7

    Illustrations- Rear Panels DCM 10 and DCM 10D (Digital In puts only on DCM 10D model) DCM 30 and DCM 30D (Digital Inputs only on DCM 30D model) 1- Firmware update mode se lect 2- USB port 3- External loudpseaker connector and s elect 4- Subwoofer output 5- Alternate equalization se lect input 6- Auxiliary audio in put 7- Hearing impaired output 8- ...

  • QSC DCM 10 - page 8

    Hardware Description Front Panel The front pa nel of the DCM series res embles traditio nal cinema mon itor produc ts. This provid es the proje ctionist a well known a nd easy to understand i nterface. Power Switch: The power on/off switch is the master cont rol for the DC M and the am plifiers conn ected to it. Amplifiers must be connected t o the ...

  • QSC DCM 10 - page 9

    Hardware Description (continued) NOTE: The DCM 10 and DCM 10D ha ve one output for ea ch surround zone an d 4 sub outputs. NOTE: All combining of the individual fre quency outputs (2 -way , 3-way , or 4-way) is done automat ically , so all front panel moni - toring is of a full frequency signal. Monitor V olume : The Monit or V olume control i s us ...

  • QSC DCM 10 - page 10

    Hardware Descri ption (continued) Rear Panel Amplifier DataPorts: Each DataPort provides two channels of audio from the DCM to the QSC amplifier in put, as well a s current and voltage monitoring of the amp’ s loudsp eaker outpu ts. Remote po wer on/st andby contr ol of the a mplifier is also provide d, all ow- ing the DCM to act as a mas ter sys ...

  • QSC DCM 10 - page 11

    Hardware Description (continued) BYP ASS CROSSOVER MODE Switch : The BYP ASS CROSSOVER MODE switch routes the center chan nel input sign al through th e 2-way or 3-wa y bypass cro ssover on the DCM 30/ 30D. On the DCM 10/10D, the ce nter channe l is routed t hrough the 2 -way bypass cros sover or not proc essed at all (pas sive bypass). Bypass Cros ...

  • QSC DCM 10 - page 12

    Mounting Rack Mounting When rack mou nting the DCM, s ecure the DCM to th e rack rails using four ma chine screws and washers o f the proper s ize. Most US rack equipment acce pt s #10-32 machines screws; length us ed depends upon applicat ion. The DC M will require 3-RU (rack units) of space. T o rack mount your DCM: 1- select moun ting location 2 ...

  • QSC DCM 10 - page 13

    Software Description DCM Manager Windows Software T o access the functions of the DCM hardware , you must use QS C’ s DCM Manager 2007 co ntrol software . A USB cable is us ed to conne ct your PC to the DCM. One of the computer ’ s available USB ports pro vides communications between the DCM Mana ger software a nd the DCM hardware. The PC mus t ...

  • QSC DCM 10 - page 14

    Connections Making the re quired conn ections to t he DCM is simp le. Just make sure that you have all of the co rrect cables . “Mass-te rminatio n” connectors are used whe rever possib le. This re duces insta llation time fr om hours to minutes and ma kes any req uired conn ection changes fas t, easy , and reliable . Requir ed Cables 1- IEC-st ...

  • QSC DCM 10 - page 15

    Connections (continued) DataPort The QSC DataPo rt conne ction carr ies input si gnals, am plifier output moni toring sig nals, remote a mplifier powe r on/ standby contro l, amplifier temperature, and more, all o n one cable. Each DataPort is clearly marked indica ting which channel’ s amplifier it should be connected to. Follow the back panel l ...

  • QSC DCM 10 - page 16

    Connections (continued) MAIN ANALOG INPUT Pino ut Configurati on: 25-pin S ubD male to 25-pin SubD male. Pin # Signal Desc ription 1 Chassis Ground 2 Left + MAIN ANALOG INPUT 3 Left Center - 4 Chassis Ground 5 Center + 6 Right Cent er - 7 Chassis Ground 8 Right + 9 Chassis Ground 10 Surround L eft - 11 Surround Right - 12 Subwoo fer - 13 Chassis Gr ...

  • QSC DCM 10 - page 17

    Connections (continued) DIGIT AL INPUT Pinout Configura tion: 25-p in SubD male to 25-pin Su bD male. Pin # Signal Descri ption 1 (not used) 2 (not used) DIGIT AL INPUT 3 ( n o t u s e d ) 4 (not used) 5 (not used) 6 (not used) 7 AES1 (L/R) OUT + 8 AES3 (Ls/Rs) OUT + 9 Chassis Ground 10 X1/2 OUT + 11 Chassi s Ground 12 (not us ed) 13 (not us ed) 14 ...

  • QSC DCM 10 - page 18

    Connections (continued) Powered Subw oofer Screw termin al connections mak e it possible to send a bala nced signal to a power ed subwoofer . This signal is balanced and the circu itry is de signed for long cable r uns from the proje ction booth to the theater sc reen. The high-pa ss filtering an d level adjustments are done by the DCM unit. NOTE: ...

  • QSC DCM 10 - page 19

    Sy stem Calibration When installing a typical ci nema sound sy st em, most of the calibration involves the Cinema Processor . Refer to the user manual for the Cinema Proc essor tha t you are usi ng. WAR NING: T urn the Gain Controls on all of the sy stem’ s amplifiers all the way down until crossover setting s and levels are verified! Connect a P ...

  • QSC DCM 10 - page 20

    T roubleshooting If the DCM Manager program is unable to commun icate with the DCM hardware... • V erify the USB cable con nections. Re- seat each ca ble-end. • T ry a known-good USB cabl e, if possible. • Confirm the USB port you are using is oper ating properly . Windows has provisions f or checking hardwar e in the Windows Contro l Panel. ...

  • QSC DCM 10 - page 21

    T roubleshootin g (continued) If theater audio is distorted ... • V erify that the DCM In put Clip LED i s not lit. If it is, the cinema processor out put signal needs to be turned do wn. •If any of the ampl ifier CLIP warnin g LEDs are illuminat ing, the output level of the DCM must be reduced or ampl ifier input sen si- tivity must be reduced ...

  • QSC DCM 10 - page 22

    Specifications DCM Inputs, Main Analog, Surround EX Input Stage T ype Active balanc ed Impedance 20k ohms, Diff erential a nd Single-en ded Maximum Input Leve l +14 .2 dBu (4.0 Vrms) A-to-D Conver sion 24-bit delta-sigma 128x oversa mpled DCM Inputs, Digital (AES/EBU) Input T ype Balanced Input Impedance 120 ohms Input Sample Rate AES/EBU sa mple r ...

  • QSC DCM 10 - page 23

    Specifications (continued) Hearing Impaired Output Output Stage T ype Sin gle-ended ba lanced impeda nce Output Impedanc e 50 ohms Nominal Output Level -11.8 dBu ( 200 mVrms) Loading Requir ements Rmin= 2k ohms, Cmax= 4 nano Farads AL T EQ Input Input T ype Contact clo sure across terminals Monitor Loudspe aker Driver 4.5-inch full-range Amplifier ...

  • QSC DCM 10 - page 24

    How to Contact QSC Audio Products Mailing address: QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA T elepho ne Numbers: Main Number (714) 754-6175 Sales & Marketing (714) 957-7100 or toll free (USA only) (800) 854-4079 Customer Service (714) 957-7150 or toll free (USA only) (800) 772-2834 Facsimile Numbers: Sales ...

Manufacturer QSC Category Computer Monitor

Documents that we receive from a manufacturer of a QSC DCM 10 can be divided into several groups. They are, among others:
- QSC technical drawings
- DCM 10 manuals
- QSC product data sheets
- information booklets
- or energy labels QSC DCM 10
All of them are important, but the most important information from the point of view of use of the device are in the user manual QSC DCM 10.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals QSC DCM 10, service manual, brief instructions and user manuals QSC DCM 10. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product QSC DCM 10.

Similar manuals

A complete manual for the device QSC DCM 10, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use QSC DCM 10 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of QSC DCM 10.

A complete QSC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual QSC DCM 10 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the QSC DCM 10, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the QSC DCM 10, that we can find in the current document
3. Tips how to use the basic functions of the device QSC DCM 10 - which should help us in our first steps of using QSC DCM 10
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with QSC DCM 10
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of QSC DCM 10 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning QSC DCM 10?

Use the form below

If you did not solve your problem by using a manual QSC DCM 10, ask a question using the form below. If a user had a similar problem with QSC DCM 10 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)