English dropdown-ico

Manual Pelco C2434M

16 pages 0.28 mb
Download

Go to site of 16

Summary
  • Pelco C2434M - page 1

    CC5BCBW Series Heavy-Duty Spectra ® Back Box Installation Manual C2434M (7/01) Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120 ® ...

  • Pelco C2434M - page 2

    2 Pelco Manual C2434M (7/01) IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be obser ved. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA T ype 3, 3R, 3S, 4, 4X ,6 o ...

  • Pelco C2434M - page 3

    Pelco Manual C2434M (7/01) 3 DESCRIPTION The Heavy-Duty Spectra is perfect for installations where structural integrity and vandalism are a prior ity . The system features hea vy-duty constr uction and tamper-resistant barrel ke y locks . The in-ceiling model has a reinforced brac ket mounting system for installation in a fixed ceiling. Pendant mod ...

  • Pelco C2434M - page 4

    4 Pelco Manual C2434M (7/01) 00535 SPRING CLIP 8-32X.275 INCH SCREW 00537 00530 00531 00532 CEILIN G MOUNTING RING S 00533 AT TA C H S A F E T Y CHAIN HERE 00534 INST ALLA TION OF IN-CEILING MODEL STEP 1 - PREP ARE CEILING a. Locate the center point of the mount- ing location. Drill a hole in the ceiling using a 3/32-inch drill. b. Insert the compa ...

  • Pelco C2434M - page 5

    Pelco Manual C2434M (7/01) 5 LABEL SW1 L A B E L S W 2 SW1 SW2 RS-422 TERMINA TION SWITCH ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 SW2 00538 GREEN T AB RED T AB 00539 BARREL KEY LOCK BALL STUD RECEIVER BALL STUD 00497 TRIM LEASH TO USE YOUR DOME, REFER TO THE OPERA TION AND PROGRAMMING MANUAL. +5 to +24 VDC NOT USED NOT USED TX- TX+ VIDEO IN CONTROLLE ...

  • Pelco C2434M - page 6

    6 Pelco Manual C2434M (7/01) INST ALLA TION OF PENDANT MODELS STEP 1 - DISASSEMBLE BACK BOX a. Tu rn the thumbscre w and open the hinged door located inside the back box. 01082 01081 01080 b. Unscrew the three Phillips scre ws located under neath the hinged door . Remove the inside portion of the back box. c. Remov e the inside mounting plate by lo ...

  • Pelco C2434M - page 7

    Pelco Manual C2434M (7/01) 7 STEP 3 - INST ALL THE BACK BOX 01079 01078 a. Secure the conduit fitting to the hole located on the inside base of the octagonal back box. b. Pull the cable and wiring for the system through the octagonal back box and conduit fitting. Mount the back bo x to the mounting surface , cor ner , or pole mount. c. Thread the c ...

  • Pelco C2434M - page 8

    8 Pelco Manual C2434M (7/01) STEP 5 - INST ALL DOME DRIVE LABEL SW1 L A B E L S W 2 SW1 SW2 RS-422 TERMINA TION SWITCH ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 SW2 00538 a. Set the DIP switches f or SW1 and SW2 on the bottom of the dome drive for the appropriate receiver address. Refer to the labels on the dome drive or T ables C through E in the Appe ...

  • Pelco C2434M - page 9

    Pelco Manual C2434M (7/01) 9 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Unit does not operate. The controller is not communicating with the Spectra unit. Fan does not operate. Ve r tical roll on monitor when switching between cameras. DOME 1 POWER DOME 2 POWER DOME 3 POWER Check to see if the red LED on the circuit board in the back box is lit ...

  • Pelco C2434M - page 10

    10 Pelco Manual C2434M (7/01) APPENDIX Ta b le A. Video Coaxial Cable Requirements Cable T ype* Maximum Distance RG59/U 750 ft (229 m) RG6/U 1,000 ft (305 m) RG11/U 1,500 ft (457 m) * Minimum cable requirements: 75 ohms impedance. All-copper center conductor . 95% braided copper shield. Ta b le B. 24 V A C Wiring Distances The follo wing are the re ...

  • Pelco C2434M - page 11

    Pelco Manual C2434M (7/01) 11 Ta b le D. Switch Settings f or SW2 – P-T ype Control NOTE: F or Coaxitron controls , SW2 is not used; set all s witches OFF . For D-type control systems , refer to T able E. Baud Rate Switch Setting SW2-6 SW2-7 SW2-8 2400 OFF OFF OFF 4800 ON OFF OFF 9600 OFF ON OFF Receiver Switch Setting Address SW2-1 SW2-2 SW2-3 S ...

  • Pelco C2434M - page 12

    12 Pelco Manual C2434M (7/01) Ta b le E. Switch Settings for SW2 – D-T ype Control (continued) (Continued on next page) Receiver Switch Setting Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 49 ON OFF OFF OFF ON ON OFF OFF 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF ON OFF ON ON OFF OFF 53 ON OFF ON OFF ON O ...

  • Pelco C2434M - page 13

    Pelco Manual C2434M (7/01) 13 Ta b le E. Switch Settings for SW2 – D-T ype Control (continued) Receiver Switch Setting Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 161 ON OFF OFF OFF OFF ON OFF ON 162 OFF ON OFF OFF OFF ON OFF ON 163 ON ON OFF OFF OFF ON OFF ON 164 OFF OFF ON OFF OFF ON OFF ON 165 ON OFF ON OFF OFF ON OFF ON 166 OFF ON ...

  • Pelco C2434M - page 14

    14 Pelco Manual C2434M (7/01) SPECIFICA TIONS MECHANICAL Construction Back box: Aluminum Dome drive: Aluminum, ABS plastic Lower dome: Acrylic Cable Entry In-Ceiling: .75-inch (1.91 cm) conduit fitting Pendant: Through 1.5-inch (3.81 cm) NPT pendant mount Pan Movement: 360 ° continuous pan rotation Vertical Tilt: Unobstructed +2 ° to -92 ° Manua ...

  • Pelco C2434M - page 15

    Pelco Manual C2434M (7/01) 15 GENERAL Environment In-Ceiling: Indoor only Pendant: Indoor/outdoor Operating Range In-Ceiling: 32 to 122 ° F (0 to 50 ° C) Pendant: (Assumes no wind chill factor; for detailed test conditions, contact Pelco) Maximum: 140 ° F (60 ° C) absolute maximum 122 ° F (50 ° C) sustained maximum Minimum -15 ° F (-9.4 ° C ...

  • Pelco C2434M - page 16

    16 Pelco Manual C2434M (7/01) REVISION HISTOR Y Manual # Date Comments C2434M 7/01 Original version. P elco, the P elco logo, Camclosure , Esprit, Genex, Legacy , and Spectra are registered trademarks of P elco. © Copyright 2001, Pelc o. Endura and ExSite are trademarks of P elco. All rights reser v ed. PRODUCT WARRANTY AND RETURN INFORMA TION WAR ...

Manufacturer Pelco Category Saw

Documents that we receive from a manufacturer of a Pelco C2434M can be divided into several groups. They are, among others:
- Pelco technical drawings
- C2434M manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco C2434M
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco C2434M.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco C2434M, service manual, brief instructions and user manuals Pelco C2434M. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco C2434M.

Similar manuals

A complete manual for the device Pelco C2434M, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco C2434M by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco C2434M.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco C2434M - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco C2434M, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco C2434M, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco C2434M - which should help us in our first steps of using Pelco C2434M
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco C2434M
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco C2434M in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco C2434M?

Use the form below

If you did not solve your problem by using a manual Pelco C2434M, ask a question using the form below. If a user had a similar problem with Pelco C2434M it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)