English dropdown-ico

Manual JAMO APS-620N

12 pages 0.24 mb
Download

Go to site of 12

Summary
  • JAMO APS-620N - page 1

    128-8613a 1 of 12 Page 1 Model APS-620N Inst allation Manual This Remote St art System is designed to be used with Automatic T ransmission- Fuel Injection V ehicles Only! COMPONENTS: Control Module 2 Four Button RF T ransmitters Antenna/Receiver 1 1” X 1.75” Foam Pad 6 Pin Main Power Harness 7 Pin Accessory Harness 1 Hood Pin Switch 2 Pin Door ...

  • JAMO APS-620N - page 2

    128-8613a 2 of 12 Page 2 INST ALLA TION OF THE MAJOR COMPONENTS: CONTROL MODULE: Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin main wiring harness. Be certain that the chosen location ...

  • JAMO APS-620N - page 3

    128-8613a 3 of 12 Page 3 the remote start unit. If the vehicle is being worked on, this hood switch prevents the remote start activation even if the RF command to start is issued. This switch must be installed in all applications. Failure to do so may result in personal injury or property damage. Mount the switch in the hood locations away from wat ...

  • JAMO APS-620N - page 4

    128-8613a 4 of 12 Page 4 YELLOW W ire: S tarter Output Careful consideration for the connection of this wire must be made to prevent the vehicle from st arting while in gear . Understanding the difference between a me- chanical and an electrical Neutral Start Switch will allow you to properly identify the circuit and select the correct installation ...

  • JAMO APS-620N - page 5

    128-8613a 5 of 12 Page 5 3 Wire Ground Switched Door Lock Circuits: In this application, the Red wire of the 2 pin harness provides a ground pulse during the arming sequence, or pulsed ground lock output. Connect the Red wire to the low current ground signal wire from the factory door lock switch to the factory door lock relay . The Green wire of t ...

  • JAMO APS-620N - page 6

    128-8613a 6 of 12 Page 6 Wiring The 4 Pin Auxiliary Output Harness, Connector “A” The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during different stages of the Remote S tart unit's operation. Understanding these outputs and the time in which they occur will allow you to determine if t ...

  • JAMO APS-620N - page 7

    128-8613a 7 of 12 Page 7 2 Pin V alet/Program/Override Push-Button Switch, Connector “D” The Black & Grey twin lead wires loaded in the two pin blue connector are the ground supply and program/valet/override input of the Remote S tart unit. Route the two wires from the previously installed Push-Button switch to the mating connector on the c ...

  • JAMO APS-620N - page 8

    128-8613a 8 of 12 Page 8 3 Pin Antenna/Receiver , Connector “F” Route the 3 pin connector from the previously installed antenna receiver assemble to the mating connector on the control module. This connector supplies 5 volts, ground and RF data from the antenna receiver to the remote start module. Be certain this connector is firmly seated maki ...

  • JAMO APS-620N - page 9

    128-8613a 9 of 12 Page 9 T o test this circuit, while the vehicle is running under control of the remote start unit, open the vehicle’s hood. The remote start unit should shut down immediately . If not, check the wiring to the control module and the under hood pin switch. DO NOT RELEASE THE VEHICLE TO THE CONSUMER IF THIS CIRCUIT DOES NOT PERFORM ...

  • JAMO APS-620N - page 10

    128-8613a 10 of 12 Page 10 The Light Blue wire can be used to accommodate the following situations: A. Shock Sensor By Pass: B. Additional Ignition Output: C. GM V A TS Key Override: Green w/ White trace Wire: Entry Illumination Ground Output This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm the alarm ...

  • JAMO APS-620N - page 11

    128-8613a 11 of 12 Page 11 Setting Up The System Programming Features: Bank 1 Transmitter Channels S tart with the system disarmed, turn the ignition switch to the on position then: 1) Press and release the push button valet/program switch 3 times. Siren Chirps once and or Lights flash one time indicating the transmitter program mode successfully e ...

  • JAMO APS-620N - page 12

    128-8613a 12 of 12 Page 12 4 PIN IN VEHICLE DA T A BUS PORT (DBI Port) The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface modules. These modules are used to access a variety of features in the vehicle which can be as simple as door trigger inputs, to more complex door locks outputs, or transponder inter ...

Manufacturer JAMO Category Remote Starter

Documents that we receive from a manufacturer of a JAMO APS-620N can be divided into several groups. They are, among others:
- JAMO technical drawings
- APS-620N manuals
- JAMO product data sheets
- information booklets
- or energy labels JAMO APS-620N
All of them are important, but the most important information from the point of view of use of the device are in the user manual JAMO APS-620N.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals JAMO APS-620N, service manual, brief instructions and user manuals JAMO APS-620N. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product JAMO APS-620N.

Similar manuals

A complete manual for the device JAMO APS-620N, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use JAMO APS-620N by users. Manuals are usually written by a technical writer, but in a language understandable to all users of JAMO APS-620N.

A complete JAMO manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual JAMO APS-620N - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the JAMO APS-620N, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the JAMO APS-620N, that we can find in the current document
3. Tips how to use the basic functions of the device JAMO APS-620N - which should help us in our first steps of using JAMO APS-620N
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with JAMO APS-620N
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of JAMO APS-620N in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning JAMO APS-620N?

Use the form below

If you did not solve your problem by using a manual JAMO APS-620N, ask a question using the form below. If a user had a similar problem with JAMO APS-620N it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)