English dropdown-ico

Manual Harbor Freight Tools 34202

14 pages 0.65 mb
Download

Go to site of 14

Summary
  • Harbor Freight Tools 34202 - page 1

    40 LB. PRESSURIZED SANDBL ASTER ASSEMBL Y and OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd. / Camarillo, CA 9301 1 Copyright © 1997 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight T ools. For t ...

  • Harbor Freight Tools 34202 - page 2

    SPECIFICA TIONS Capacity: 40 lbs. Working Pressure 60-125 PSI Delivery Rate 6-25 CFM Overall Dimensions 33.5" x 18.75" x 13" Weight: 57 lbs. SA VE THIS MANUAL Y ou will need the manual for the safety warnings and cautions, assembly instructions, operating procedures, maintenance procedures, trouble shooting, parts list, and diagram. ...

  • Harbor Freight Tools 34202 - page 3

    9. DO NOT ABUSE THE POWER CORD. Do not yank compressor ’s cord to disconnect it from the receptacle. Do not carry tools by the cord. 10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or across running machines. 11 . MAINT AIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow i ...

  • Harbor Freight Tools 34202 - page 4

    22. MAINT AIN CORRECT AIR PRESSURE WHENEVER WORKING . Do not allow pressure to exceed 125 PSI. If the safety valve does not release excess air pressure, stop all work and use the air compressor to release pressure in the tank. Do not attempt any repairs to the Sandblaster until its gauge reads “0”. AIR/SAND SUPPL Y REQUIREMENTS Hose Hose Nozzle ...

  • Harbor Freight Tools 34202 - page 5

    ASSEMBL Y NOTE: Use T eflon® Pipe T ape on all threaded joints. Make sure all joints are securely tighten. Intake Manifold Refer to Figure 1. S tep1: Get out the INT AKE MANIFOLD (#14), PRESSURE GAUGE (#15), BRASS THROTTLING V AL VE (#18A), 3/8" 1/4" NIPPLE CONNECTOR (#20), and JOINT PIPE (#13). S tep2: Attach the PRESSURE GAUGE to the t ...

  • Harbor Freight Tools 34202 - page 6

    Water Trap Refer to Figure 2. Figure 2 — Water Trap Assembly S tep1: Get out the WA TER TRAP (#17), two 3/8" NIPPLE CONNECTORS (#16), the BRASS AIR SUPPL Y V AL VE (#18), and the MALE/FEMALE ADAPTER (#19). S tep2: A tt ach the 3/8" NIPPLE CONNECTORS to either side of the W A TER TRAP . S tep3: On the top of the WA TER TRAP is an arrow . ...

  • Harbor Freight Tools 34202 - page 7

    Nozzle Shut Off V alve Refer to Figure 4. S tep1: Get out the HOSE ADAPTER (#25), the STEEL SHUT OFF V AL VE (#18C), a NIPPLE CONNECTOR (#16), the GASKET (#26), the desired size NOZZLE (#27A-D), and the NOZZLE CAP NUT (#28). S tep2: Put the front of the NOZZLE through the NOZZLE CAP NUT . S tep3: Attach the NOZZLE CAP NUT to the NIPPLE CONNECTOR wi ...

  • Harbor Freight Tools 34202 - page 8

    S tep5: At t ach the HOSE ADAPTER to the other end of the STEEL SHUT OFF V AL VE. Sand Control V alve/ Nozzle Shut Off V alve Refer to Figure 5. Sand Con trol V alve Assem bly Sand Hose Nozzle Shut O ff V alve Asse m bly Hose Clamp (# 23) Figure 5 — Sand Control V alve / Shut Off V alve Assembly S tep1: Get out the Sand Control V alve & Nozzl ...

  • Harbor Freight Tools 34202 - page 9

    T op Assembly Refer to Figure 6. T ank (# 1) Ni pple Connector (# 16) Ni pple Connector (# 16) Air Hos e (# 21) Gasket (# 1 1) Air Ca p (# 12) Joint P ipe (# 13) Figure 6 — T op Assembly S tep1: Get the Int ake V alve Assembly , the W ater Trap Assembly , the T ank Assembly , the T ANK CAP (#12), the O-RING (#1 1), and the AIR HOSE (#21). S tep2: ...

  • Harbor Freight Tools 34202 - page 10

    Handle Bars Refer to Figure 7. Handl e Grip (# 7) Handl e B ar (# 6) Scre w (# 8) W asher (# 31) Nut (# 9) Figure 7 — Handle Bar Assembly S tep1: Get out the two HANDLE BARS (#6), the two HANDLE GRIPS (#5), the four SCREWS (#8), four NUTS (#9), and four W ASHERS (#31). S tep2: Sl ide the HANDLE GRIPS onto the HANDLE BARS. S tep3: A tt ach both HA ...

  • Harbor Freight Tools 34202 - page 11

    Wheels and Foot See Figure 8. 5 3 2 4 3 3 2 Figure 8 - Wheel and Foot Attachment S tep 1: Get out the two WHEELS (#2), the three COTTER PINS (#3), the FOOT (#4) and the AXLE (#5). S tep 2: Attach the FOOT to the T ANK (#1) using one of the COTTER PINS. S tep 3: Attach one of the WHEELS to the AXLE using one of the COTTER PINS. S tep 4: Slide the AX ...

  • Harbor Freight Tools 34202 - page 12

    OPERA TIONS Loading Abrasives S tep 1: Check to insure the abrasives are dry and clean so that they do not clog the unit. S tep 2: Close the AIR SUPPL Y V AL VE (#18) by turning it to the horizontal position. S tep 3: Open the NOZZLE SHUT OFF V AL VE (#18C) by turning it to the vertical position. S tep 4: Make sure the PRESSURE GAUGE (#15) reads ? ...

  • Harbor Freight Tools 34202 - page 13

    Item# Description Q ty Item# Description Q ty 1 T a nk 1 18B 3/8" S teel Sand Control V alve 1 2 Wheel 2 18C 3/8" S teel Shut Off V alve 1 3 Cotter Pin 3 1 9 Male/Female Adapter 1 4 Foot 1 20 3/8" 1/4" Nipple Connector 1 5 Axle 1 21 Air Hose 1 6 * Handle Bar 2 22 Sand Outlet Manifold 1 7 Handle Grip 2 23 Hose Clamp 2 8 Pan Screw ...

  • Harbor Freight Tools 34202 - page 14

    19 16 16 17 15 14 18A 20 18 13 7 8 9 3 5 21 14 2 1 24 23 28 27A-D 26 16 18C 25 16 18B 16 22 23 31 12 11 10 6 3 P ARTS DRA WING Page #14 -- SKU 34202 ...

Manufacturer Harbor Freight Tools Category Sander

Documents that we receive from a manufacturer of a Harbor Freight Tools 34202 can be divided into several groups. They are, among others:
- Harbor Freight Tools technical drawings
- 34202 manuals
- Harbor Freight Tools product data sheets
- information booklets
- or energy labels Harbor Freight Tools 34202
All of them are important, but the most important information from the point of view of use of the device are in the user manual Harbor Freight Tools 34202.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Harbor Freight Tools 34202, service manual, brief instructions and user manuals Harbor Freight Tools 34202. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Harbor Freight Tools 34202.

Similar manuals

A complete manual for the device Harbor Freight Tools 34202, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Harbor Freight Tools 34202 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Harbor Freight Tools 34202.

A complete Harbor Freight Tools manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Harbor Freight Tools 34202 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Harbor Freight Tools 34202, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Harbor Freight Tools 34202, that we can find in the current document
3. Tips how to use the basic functions of the device Harbor Freight Tools 34202 - which should help us in our first steps of using Harbor Freight Tools 34202
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Harbor Freight Tools 34202
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Harbor Freight Tools 34202 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Harbor Freight Tools 34202?

Use the form below

If you did not solve your problem by using a manual Harbor Freight Tools 34202, ask a question using the form below. If a user had a similar problem with Harbor Freight Tools 34202 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)