-
Craftsman 315.27994 - page 1
Owner's Manual I ,R " ' i P O F E S S I O N A L 3/8 in. PROFESSIONAL DRILL-DRIVER Variable Speed / Reversible Double Insulated Model No. 315.279940 Save this manual for future reference _, CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. • Safety • Features • Assembly • Op ...
-
Craftsman 315.27994 - page 2
• Table of Contents ........................................................................................................................................................ 2 • General Safety Rules .............................................................................................................................................. 2-3 ? ...
-
Craftsman 315.27994 - page 3
Tool Use and Care Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. • Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is des ...
-
Craftsman 315.27994 - page 4
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hiddenwiring or its cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. Additional Rules For Safe Operation Know your power tool. Read operator's manual carefully. Le ...
-
Craftsman 315.27994 - page 5
SYMBOLS SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time Alternating Current Type or a characteristic of current --_ Direct Current Type or a characteristic of current no No Load Speed Rotational speed, at no load .../min Revolutions or Reciprocation Per Minute Revolutions ...
-
Craftsman 315.27994 - page 6
KNOW YOUR DRILL-DRIVER See Figure 1. Before attempting to operate your drill-driver, familiarize yourself with all operating features and safety require- ments. ,_ WARNING: Carefully read through this entire owner's manual before using your new drill-driver. Pay close attention to the Rules For Safe Operation, Warnings and Cautions. If you use ...
-
Craftsman 315.27994 - page 7
TWO SPEED BIT STORAGE AREA GEARTRAIN (HI-LO) AUXILIARY HANDLE KEYLESS CHUCK TORQUE SWITCH ADJUSTMENT TRIGGER RING SCREWDRIVER BITS_ DIRECTION OF ROTATION SELECTOR (FORWARD/REVERSE) LOCK-ON BuIrON Fig. 1 ,_ WARNING: If any parts are missing, do not operate your drill-driver until the missing parts are replaced. Failure to do so could result in possi ...
-
Craftsman 315.27994 - page 8
SWITCH See Figure 3. To turn your drill ON, depress the switch trigger. Release switch trigger to turn your drill OFF. FORWARD/REVERSE SELECTOR CENTERPOSITION (LOCK) SWITCH TRIGGER TO INCREASESPEED, DEPRESS SWITCH TRIGGER LOCK-ON BUTTON Fig. 3 LOCK-ON BUTTON See Figure 3. Your drill is equipped with a lock-on feature which is convenient when contin ...
-
Craftsman 315.27994 - page 9
REVERSIBLE See Figure 5. This tool has the feature of being reversible. The direction of rotation is controlled by a selector located above the switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch for drilling. The drilling direction is reversed when the ...
-
Craftsman 315.27994 - page 10
BIT STORAGE See Figure 8. When not in use, bits provided with your drill can be placed in the storage area located on the top of your drill as shown in figure 8. BIT STORAGE AREA SCREWDRIVER BITS Fig. 8 ,_ WARNING: Always wear safety goggles or safety glasses with side shields when operating your drill. Failure to do so could result in dust, shavin ...
-
Craftsman 315.27994 - page 11
CHUCK REMOVAL See Figure 10, 11, and 12. The chuck must be removed in order to use some accessories. To remove: • Unplug your drill. ,_i WARNING: Failure to unplug your drill could result in accidental starting causing serious injury. • Place two speed gear train in the low setting and rotate torque adjusting ring to the maximum torque setting. ...
-
Craftsman 315.27994 - page 12
I 1]=1 GENERAL All parts represent an important part of the double insulation system and should be serviced only at a Sears Service Center. Avoid using solvents when cleaning plastic pads. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, ...
-
Craftsman 315.27994 - page 13
The following recommended accessories are currently available at Sears retail stores. • High Speed Bits (For wood or metal) ......... 1/2 in. Max. • Masonry Bits ............................................... 3/4 in. Max. • Wood Boring Bits ........................................... 1 in. Max. • Hole Saws ................................. ...
-
Craftsman 315.27994 - page 14
14 ...
-
Craftsman 315.27994 - page 15
CRAFTSMAN 318 in. PROFESSIONAL DRILL-DRIVER MODEL NO. 315.279440 I The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your CRAFTSMAN 318 In. PROFESSIONAL DRILL-DRIVER or when ordering parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS I 5 SEE NOTE"A" 3 ...
-
Craftsman 315.27994 - page 16
Get it fixed, at your home or ours! For repair of major brand appliances in your own home... no matter who made it, no matter who sold ifl 1-800-4-MY-HOME s_ Anyt,me, day or n,ght (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Re ...
Do you have a question concerning Craftsman 315.27994?
Use the form below
If you did not solve your problem by using a manual Craftsman 315.27994, ask a question using the form below. If a user had a similar problem with Craftsman 315.27994 it is likely that he will want to share the way to solve it.