Manual Oricom UHF200

36 pages 2.38 mb
Download

Go to site of 36

Summary
  • Oricom UHF200 - page 1

    Operating Instructions For UHF100 and UHF200 40 Channel UHF 2-way Citizen Band Radio UHF100 UHF200 ...

  • Oricom UHF200 - page 2

    ...

  • Oricom UHF200 - page 3

    3 T able of contents This unit complies with all relevant Australian and New Zealand approval requirements. T able of contents .......................................................................... 3 Safety Information and Warnings .................................................. 4 Controls and Connectors ..................................... ...

  • Oricom UHF200 - page 4

    4 Safety Information and Warnings Please read before installing or opearating Y our Oricom Radio The operation of this radio in Australia and New Zealand is subject to conditions in the following licenses. In Australia the ACMA Radio communications (Citizen Band Radio Stations) and in New Zealand by MED General User Radio License for Citizen Band R ...

  • Oricom UHF200 - page 5

    5 Box Contents UHF200 1 x RF Radio 1 x Controller Speaker Micrphone 1 x DC Power Cord with inline fuse 1 x Mounting bracket with mounting screws for RF Radio 1 x Microphone Hanger 1 x 2m long Extention cable 1 x Coupler for extention cable 1 x User Guide UHF100 1 x RF Radio 1 x Remote Head Unit with 2m cable 1 x UHF100 Standard Microphone 1 x DC Po ...

  • Oricom UHF200 - page 6

    6 Controls and Connectors Front View Remote Head unit (UHF100) 1. Microphone connector 2. LCD Display 3. Power On/Off, channel & V olume control 4. Function button by short push & Duplex On/Off by long push 5. Open Scan, Memor y On/Off, Group Scan 6. Priority Channel On/Off, Key Lock On/Off, Alpha-numeric display 7. ID setting, 5 tone SelCa ...

  • Oricom UHF200 - page 7

    7 Controls and Connectors Rear View Rear view of Radio (UHF100 & 200) 1. 3.5mm external jack for optional 8 ohm speaker 2. Power Supply connection 3. Antenna connection Standard Microphone (UHF100) 1. Push T o T alk (PTT) button 2. Volume Up , Channel Up 3. Volume Down , Channel Down 4. Power On/off, V olume and channel selector 3 2 1 1 2 4 3 ...

  • Oricom UHF200 - page 8

    8 Controls and Connectors T op view of Contoller Speaker Microphone (UHF200) 1. Volume Down , Channel Down 2. Volume Up , Channel Up 3. Power On/Off Front view of Contoller Speaker Microphone (UHF200) 4. LCD Display 5. Function button & Duplex On/Off 6. Open Scan, Memor y On/Off, Group Scan 7. Priority Channel On/Off, Key Lock On/Off, Alpha-num ...

  • Oricom UHF200 - page 9

    9 Controls and Connectors LCD Icons & Indicators (UHF100 and UHF200) 1. FUNCTION 2. RX or TX Signal strength 3. T ransmitter Indicator 4. Receiver Indicator 5. Quiet mode 6. Priority On/Off 7. Monitor On/Off 8. Memory On/Off 9. Key Lock 10. Open Scan 11. Group Scan 12. Selelctive call Sending_to 13. Selective call Receiving from 14. 38 CTCSS T ...

  • Oricom UHF200 - page 10

    10 Installation INST ALLA TION CAUTION When installing your radio in your vehicle, check that during installation you do not damage any wiring or vehicle components that may be hidden around the mounting position. If you are unsure about how to install your radio, we suggest for optimum performance you have your radio professionally installed by a ...

  • Oricom UHF200 - page 11

    11 1. Fix the mounting bracket in place by screwing through the slots in the bracket. 2. Fix the remote head unit to the mounting bracket with the thumb screws provided. 3. Connect the standard microphone to the remote head socket, and tighten up the thumb screw . Fitting the Controller Microphone Speaker (UHF200) The Remote Head uses an 8 pin tele ...

  • Oricom UHF200 - page 12

    12 Disconnecting the Remote Head/Speaker Controller Microphone It is recommended that the remote head be left permanently connected to the radio, but if it must be disconnected, proceed as follows: 1. Lift the rubber boot and the lip of the raised area on the front panel. 2. Ease the rubber boot out of the cable entr y hole and slide it along the c ...

  • Oricom UHF200 - page 13

    13 Radio stays ON when the ignition is switched OFF Connect the radio's negative (black) lead to the vehicle chassis, or directly to the batteries negative terminal. Connect the radio's positive (red) lead via the 2 Amp fuse to the batter y's positive terminal. Alternatively , the positive lead could be connected at the fuse box at a ...

  • Oricom UHF200 - page 14

    14 Operations P ower on and off * Press and hold the PWR button on the UHF100 Remote Head or the UHF200 microphone PWR button for 2 seconds. * The default channel is set at CH01. 200R X CH 200R X CH UHF100 UHF200 Volume control * The UHF100 has a rotar y electric volume control. Adjust the volume by rotating the channel knob clock-wise or adjust th ...

  • Oricom UHF200 - page 15

    15 Operations 200R X CH 200R X CH blinking T ri Function buttons T o use the primar y function ( F , SC, PRI, ID, MO ) press the required button. T o use the secondar y function ( DPX, MEM, LO , C AL, TSQ ) press and hold the button for 2 seconds. T o use the third function ( OS/GS, ALPHA, QUIET , MENU ), press F/DPX and press the required button. ...

  • Oricom UHF200 - page 16

    16 Operations Priority Channel T o store a Priority Channel, press the PRI/LO button. The letter "P" will appear when the priority channel is set. The channel you selected as your Priority Channel will then be automatically monitored during the Group Scan. Note: Y ou can only store one channel as your priority channel. T o store a Priorit ...

  • Oricom UHF200 - page 17

    17 Operations Selecting the Required CTCSS T one T o pre-select the CTCSS tone on your radio, please refer to the MENU settings on page 24. Enabling CTCSS on a Channel If a CTCSS tone has been selected, it can be enabled on individual channels. 1. Rotate the Channel knob to select the required channel. The letters "CT" will appear . 2. Pr ...

  • Oricom UHF200 - page 18

    18 Open Scan Group Scan With Group Scan the Radio scans for activity , but in addition, it also inserts your Priority Channel into the scan sequence. This means that your Priority Channel will be monitored regularly while scanning to ensure that no calls are missed. Any signals received on your Priority Channel will take precedence over any signals ...

  • Oricom UHF200 - page 19

    19 Selcall Selcall or Selective Call ing is a function that allows you to selectively call another radio, using a unique ID number . Y our radio has 10 programmable Selcall ID memories. The ID memories are displayed as "C0 to C9". Here you will program Selcall ID numbers of other radios. Y our Radio’ s Selcall Identication number is ...

  • Oricom UHF200 - page 20

    20 Entering, Editting and Storing a Selcall Name or ID number 1. Briey press the ID/CAL button. The C ALL TO mode will be selected and the last-sent Selcall memory location will be displayed. 2. Rotate the Channel knob to select the required Selcall memor y (locations C0 to C9). If no ALPHA name or ID number has been programmed for that memory , ...

  • Oricom UHF200 - page 21

    21 T o return the call Press F/DPX and hold the ID/CAL button for 2 seconds until the radio beeps. The callers Selcall Identity will be sent to the caller . Cancelling the Selcall Alert T o cancel the alarm and talk on the channel, press the PTT button. The alarm will be cancelled and the channel will be open for normal communication. Group Calling ...

  • Oricom UHF200 - page 22

    22 T o call the group, program the Base radio Group ID code to 1234A. When you call the group, all of the above vehicles will receive the Group Calling T one. Group call IDs can be stored in memory the same way as a Standard Selcall ID code, please refer to Entering, Editing and Storing a Selcall ID number at page 20. 10 Radios 100 Radios Group ID ...

  • Oricom UHF200 - page 23

    23 Setting up QUIET Mode T o setup QUIET mode you must rst ‘tag’ the channels that you want to stay quiet, then activate the QUIET mode. Once QUIET mode is activated, the channels you have tagged will remain quiet to all incoming signals unless your Selcall Ident is received. Channels not tagged will remain open to all signals and will opera ...

  • Oricom UHF200 - page 24

    24 Third functions MENU list * Use the channel knob to change the value of each setting. * Use the Scan button to select the next function. * If a button is not pressed within 8 seconds the Radio will automatically exit the menu mode. * Please see below menu modes. Control Functions STEP Display Default MENU SQ Level adjust off 7 3 OFF , CTCSS, DCS ...

  • Oricom UHF200 - page 25

    25 Operations SQL: The radio has 8 preset ( off - 7) squelch levels: off - SQ off (monitor on condition) 1 - Max sensitivity (min squelch) 7 - min sensitivity (max/tight squelch) CTCSS and DCS setting This feature allows you to receive signals only from callers who have selected the same CTCSS and DCS code. DCS is similar to CTCSS. It provides 104 ...

  • Oricom UHF200 - page 26

    26 Operations Duplex Operation General Y our radio has a Repeater Access function to allow use of local Repeater stations (if available in your area). Repeaters are shared radio system installed by interested parties (clubs, local business etc.) that pick transmissions on specic channels and re-transmit (or repeat) the received signal to another ...

  • Oricom UHF200 - page 27

    27 Operations If you transmit on CH01 duplex mode, you are actually transmitting on CH31 the repeater station down converts your signal and retransmits on CH01. Y our UHF100 and UHF200 allows you to pre-select Duplex operation individually on each channel. Push and hold the F/DPX button for 2 seconds, "DPXON" should appear on the LCD. Pus ...

  • Oricom UHF200 - page 28

    28 Operations 200 Receive (RX) only Channels Manual Programming The UHF Radio has a wide band search feature which will allow you to search Frequencies ranging from 400-512MHz (in 12.5KHz steps). Y ou may search the full range or you may search one of 4 smaller bands separately . T urn power on. Briey press the F/DPX button and then the Power bu ...

  • Oricom UHF200 - page 29

    29 Operations * pr ess th e PRI/LO button, next 2 digits will be blinking for the next frequency digits. * Rotary channel switch to select which 2 frequency digits you want. Briey press the F/DPX button and Power button to exit. Automatic programming 1. Press the PWR button to turn the radio on. 2. Briey press the F/DUP button and then the Po ...

  • Oricom UHF200 - page 30

    30 UHF channels and frequencies Channel Frequency T able Radiocommunications (Citizen Band Radio Stations) Class Licence 2002 No licence is required to own or operate this radio in Australia and New Zealand. The Radiocommunications (Citizen Band Radio Stations) Class Licence 2002 contains the technical parameters, operating requirements, conditions ...

  • Oricom UHF200 - page 31

    31 UHF channels and frequencies 15 476.775 Simplex 16 476.800 Simplex 17 476.825 Simplex 18 476.850 Simplex 19 476.875 Simplex 20 476.900 Simplex 21 476.925 Simplex 22 476.950 No Use 23 476.975 No Use 24 477.000 Simplex 25 477.025 Simplex 26 477.050 Simplex 27 477.075 Simplex 28 477.100 Simplex 29 477.125 Simplex 30 477.150 Simplex 31 477.175 Duple ...

  • Oricom UHF200 - page 32

    32 UHF channels and frequencies Channel 11 is a calling channel generally used to call others and channel 40 is the customary road vehicle channel. Once contact is established on the calling channel, both stations should move to another unused "SIMPLEX" channel to allow others to use the calling channel. Channel 22 and 23 are for T elemet ...

  • Oricom UHF200 - page 33

    33 Warranty information (Australia) Oricom makes no other warranties or conditions, express or implied, including as to merchantability and tness for a particular purpose, except as stated in this W arranty . Any implied warranties that may be imposed by law are limited in duration to the Warranty Period. Oricom warrants that the product is free ...

  • Oricom UHF200 - page 34

    34 Warranty information (Australia) In the unlikely event that your Oricom product has a recurring failure, Oricom, at its discretion, may elect to provide you with a replacement product of its choosing that is at least equivalent to your product in performance. Oricom does not warrant that the operation of the product will be uninterrupted or erro ...

  • Oricom UHF200 - page 35

    ...

  • Oricom UHF200 - page 36

    Australia Oricom International Pty Ltd Locked Bag 658 South Windsor, NSW 2756 New Zealand Oricom Live Chat www.oricom.co.nz Customer Support Email: support@oricom.com.au Web: www.oricom.com.au Phone: 1300 889 785 Fax: (02) 4574 8898 Customer Support If you suspect your product is not functioning to specication, before making a warranty claim ple ...

Manufacturer Oricom Category Marine Radio

Documents that we receive from a manufacturer of a Oricom UHF200 can be divided into several groups. They are, among others:
- Oricom technical drawings
- UHF200 manuals
- Oricom product data sheets
- information booklets
- or energy labels Oricom UHF200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Oricom UHF200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Oricom UHF200, service manual, brief instructions and user manuals Oricom UHF200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Oricom UHF200.

Similar manuals

A complete manual for the device Oricom UHF200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Oricom UHF200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Oricom UHF200.

A complete Oricom manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Oricom UHF200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Oricom UHF200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Oricom UHF200, that we can find in the current document
3. Tips how to use the basic functions of the device Oricom UHF200 - which should help us in our first steps of using Oricom UHF200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Oricom UHF200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Oricom UHF200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Oricom UHF200?

Use the form below

If you did not solve your problem by using a manual Oricom UHF200, ask a question using the form below. If a user had a similar problem with Oricom UHF200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)