Manual Hitachi D10VG

52 pages 0.45 mb
Download

Go to site of 52

Summary
  • Hitachi D10VG - page 1

    D 10VF • D 10VG D 13VF • D 13VG Model Drill Modèle Perceuse Modelo Taladro DOUBLE INSULATION DOUBLE ISOLATION AISLAMIENTO DOBLE INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI AVERTISSEMENT Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort ou de sérieuses blessures corporelles! Ce mode d’emploi contient d? ...

  • Hitachi D10VG - page 2

    CONTENTS English Page IMPORTANT SAFETY INFORMATION ...... 3 MEANINGS OF SIGNAL WORDS ...... 3 SAFETY ................................................... 4 GENERAL SAFETY RULES ................. 4 SPECIFIC SAFETY RULES AND SYMBOLS ........................................ 6 DOUBLE INSULATION FOR SAFER OPERATION ..................................... 8 ...

  • Hitachi D10VG - page 3

    English 3 IMPORTANT SAFETY INFORMATION Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accid ...

  • Hitachi D10VG - page 4

    English 4 SAFETY GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS 1. Work Area (1) Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. (2) Do not operat ...

  • Hitachi D10VG - page 5

    English 5 (4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. (5) Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. (6) Use safety e ...

  • Hitachi D10VG - page 6

    English 6 SPECIFIC SAFETY RULES AND SYMBOLS 1. Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. 2. ALWAYS wear ear plugs when using the tool for extended ...

  • Hitachi D10VG - page 7

    English 7 13. Blades and accessories must be securely mounted to the tool. Prevent potential injuries to youself or others. Blades, cutting implements and accessories which have been mounted to the tool should be secure and tight. 14. Keep motor air vent clean. The tool’s motor air vent must be kept clean so that air can freely flow at all times. ...

  • Hitachi D10VG - page 8

    English 8 DOUBLE INSULATION FOR SAFER OPERATION To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation “ means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by t ...

  • Hitachi D10VG - page 9

    English 9 FUNCTIONAL DESCRIPTION NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety instructions contained in this manual. Some illustrations in this In ...

  • Hitachi D10VG - page 10

    English 10 Model D13VF D13VG Speed of Angle Unit LOW(650/min.) HIGH(1350/min.) LOW(400/min) HIGH(900/min.) Steel Twist Bit 1/2"(13mm) 1/2"(13mm) 1/2"(13mm) 1/2"(13mm) Hole Saw 2-1/2"(64mm) 1-1/4"(32mm) 2-3/4"(70mm) 2"(51mm) Wood Flat Spade Bit 1-1/2"(38mm) 1-1/4"(32mm) 1-1/2"(38mm) 1-1/2"( ...

  • Hitachi D10VG - page 11

    English 11 ASSEMBL Y AND OPERA TION APPLICATIONS 䡬 Boring holes in metal, wood and plastic. PRIOR TO OPERATION 1. Power source Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate. 2. Power switch Ensure that the switch is in the OFF position. If the plug is connected to a recept ...

  • Hitachi D10VG - page 12

    English 12 7. Mounting and dismounting of the bit For keyed chuck (Fig. 2) (1) Open the chuck jaws, and insert the bit into the chuck. (2) Place the chuck wrench in each of the three holes in the chuck, and turn it in the clockwise direction (viewed from the front side). Tighten securely. (3) To remove the bit, place the chuck wrench into one of th ...

  • Hitachi D10VG - page 13

    English 13 The L-side of the push button is pushed to turn the bit counterclockwise. (The L and R marks are provided on the body.) 10. Attaching the angle unit. (Optional accessory for D13VF and D13VG) (1) Removing chuck from drill (Fig. 8) 䡬 To remove the chuck from the drill, open the chuck jaws as far as possible and turn out the locking screw ...

  • Hitachi D10VG - page 14

    English 14 䡬 To operate the angle unit at high speed, attach the chuck to the angle unit spindle at the side marked “HIGH” and secure the locking screw. At this setting, the drilling speed is increased to about 150% and the drilling torque decreased to about 70%. (Fig. 11) (3) Installing the side handle (Fig. 12) The side handle can be instal ...

  • Hitachi D10VG - page 15

    English 15 䢇 Do not walk about with the power tool hanging from the waist belot. 䢇 In the case of operation in a high place, it is dangerous to drop the tool accidentally. If the hook is deformed or hung from the wrong position, there is danger that the hook will slip off and the tool will fall. Be careful to avoid danger. 䢇 In making a throu ...

  • Hitachi D10VG - page 16

    English 16 MAINTENANCE AND INSPECTION WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection. 1. Inspecting the drill bits Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is n ...

  • Hitachi D10VG - page 17

    English 17 ACCESSORIES WARNING: ALWAYS use Only authorized HITACHI replacement parts and accessories. NEVER use replacement parts or accessories which are not intended for use with this tool. Contact HITACHI if you are not sure whether it is safe to use a particular replacement part or accessory with your tool. The use of any other attachment or ac ...

  • Hitachi D10VG - page 18

    18 Français INFORMATIONS IMPORTANTES DE SÉCURITÉ Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé. La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé p ...

  • Hitachi D10VG - page 19

    19 Français SECURITE REGLES GENERALE DE SECURITE AVERTISSEMENT: Lire et coxmprendre toutes les instructions. Un non respect de toutes les instructions ci-dessous peut entraîner une électrocution, un incendie et/ou de sérieuses blessures personnelles. CONSERVER CES INSTRUCTIONS 1. Zone de travail (1) Garder la zone de travail propre et bien écl ...

  • Hitachi D10VG - page 20

    20 Français (3) Eviter tout démarrage accidentel. S’assurer que le l’interrupteur d’alimentation est sur la position d’arrêt avant de brancher la machine. Transporter l’appareil avec les doigts sur l’interrupteur d’alimentation ou brancher un outil avec l’interrupteur sur la position marche invite aux accidents. (4) Retirer les c ...

  • Hitachi D10VG - page 21

    21 Français REGLES DE SECURITE SPECIFIQUES ET SYMBOLES 1. Tenir les outils par les surfaces de grippage lors de la réalisation d’opération où l’outil de coupe risque d’entrer en contact avec des câbles cachés ou son propre cordon. Un contact avec un fil “sous tension” mettra les parties métalliques de l’outil “sous tension” e ...

  • Hitachi D10VG - page 22

    22 Français 11. Maintenir toutes les vis, tous les boulons et les couvercles fermement en place. Maintenir toutes les vis, tous les boulons et les couvercles fermement montés. Vérifier leurs conditions périodiquement. 12. Ne pas utiliser les outils motorisés si le revêtement de plastique ou la poignée est fendu. Des fentes dans le revêtemen ...

  • Hitachi D10VG - page 23

    23 Français DOUBLE ISOLATION POUR UN FONCTIONNEMENT PLUS SUR Pour assurer un fonctionnement plus sûr de cet outil motorisé, HITACHI a adopté une conception à double insolation. “Double isolation” signifie que deux systèmes d’isolation physiquement séparés ont été utilisés pour isoler les matériaux conducteurs d’électricité con ...

  • Hitachi D10VG - page 24

    24 Français DESCRIPTION FONCTIONNELLE REMARQUE: Les informations contenues dans ce mode d’emploi sont conçues pour assister l’utilisateur dans une utilisation sans danger et un entretien de l’outil motorisé. NE JAMAIS utiliser ni entreprendre une révision de l’outil sans avoir d’abord lu et compris toutes les instructions de sécurit? ...

  • Hitachi D10VG - page 25

    25 Français SPECIFICATIONS Modèle D10VF D10VG D13VF D13VG Moteur Moteur série monophasé à collecteur Source d’alimentation Secteur, 120V 60 Hz, monophasé Courant 9,0A Vitesse sans charge 0-3000/min. 0-1200/min. 0-850/min. 0-600/min. Capacité de mèche 3/8" (10mm) 1/2" (13mm) Frein électrique Non Non Oui Oui Capacité Acier Foret ...

  • Hitachi D10VG - page 26

    26 Français ASSEMBLAGE ET FONCTIONNEMENT APPLICATIONS 䡬 Perçage de trous dans métal, bois et matières plastiques. AVANT L’UTILISATION 1. Source d’alimentation S’assurer que la source d’alimentation qui doit être utilisée est conforme à la source d’alimentation requise spécifiée sur la plaque signalétique du produit. 2. Interru ...

  • Hitachi D10VG - page 27

    27 Français 7. Montage et démontage de la mèche Mèche avec clavette (Fig. 2) (1) Ouvrir les mâchoires du mandrin et insérer la mèche dans le mandrin. (2) Mettre la clavette à mandrin dans chacun des trois trous du mandrin, et la tourner dans le sens des aiguilles d’une montre (vue depuis l’avant). Serrer à fond. (3) Pour retirer la mè ...

  • Hitachi D10VG - page 28

    28 Français s’assurer que la poignée latérale et le joint de poignée sont complètement installés. (Fig. 6) 9. Vérification du sens de rotation (Fig. 7) La mèche tourne dans le sens des aiguilles d’une montre (vue de l’arrière) quand on appuie sur le côté R du bouton-poussoir. Appuyer sur le côté L du bouton-poussoir pour la faire ...

  • Hitachi D10VG - page 29

    29 Français dans la section hexagonale de l’angle, et serrer le manchon de raccord à l’aide des boulons de serrage. Serrer deux boulons de serrage de façon uniforme et à tour de rôle au couple de 61-70 In . lbs (70-80 kg . cm) (force égale à un tour de poignet de la clé à fourche fournie pour le serrage des boulons de serrage). (Fig. 9 ...

  • Hitachi D10VG - page 30

    30 Français 11. Fixation du crochet (accessoire en option) (Fig. 14) Pour pouvoir fixer le crochet, il faut démonter la section de la poignée qui recouvre le circuit électrique de l’outil. Pour garantir la sécurité et préserver la protection contre les chocs électriques, l’installation du crochet sur la perceuse sera confiée EXCLUSIVEM ...

  • Hitachi D10VG - page 31

    31 Français ATTENTION : 䢇 Du fait qu’il se produit une certaine réaction lorsque le frein entre en service, bien tenir la perceuse fermement. 䢇 Si le frein ne fonctionne plus, envoyer l’outil à un SERVICE APRES-VENTE HITACHI AGREE. 3. Perçage 䡬 Pour percer des trous, démarrer la perceuse lentement, et augmenter progressivement la vit ...

  • Hitachi D10VG - page 32

    32 Français ENTRETIEN ET INSPECTION AVERTISSEMENT: S’assurer de mettre l’interrupteur d’alimentation sur la position OFF et de déconnecter la fiche de la prise secteur avant l’entretien et l’inspection de la meuleuse. 1. Vérification de la mèche L’utilisation continue d’une mèche usée et ou endommagée réduira l’efficacité d ...

  • Hitachi D10VG - page 33

    33 Français ACCESSOIRES AVERTISSEMENT: TOUJOURS utiliser UNIQUEMENT des pièces de rechange et des accessoires HITACHI. Ne jamais utiliser de pièce de rechange ou d’accessoires qui ne sont pas prévus pour être utilisé avec cet outil. En cas de doute, contacter HITACHI pour savoir si une pièce de rechange ou un accessoire particulier peuvent ...

  • Hitachi D10VG - page 34

    34 Español INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD Antes de utilizar o de realizar cualquier trabajo de mantenimiento de esta herramienta eléctrica, lea y comprenda todas las precauciones de seguridad, advertencias e instrucciones de funcionamiento de este Manual de instrucciones. La mayoría de los accidentes producidos en la operación y el man ...

  • Hitachi D10VG - page 35

    35 Español SEGURIDAD NORMAS GENERALES DE SEGURIDAD ADVERTENCIA: Lea y entienda todas las instrucciones. Si no sigue las instrucciones indicadas a continuación, pueden producirse descargas eléctricas, incendios, y/o lesiones serias. GUARDE ESTAS INSTRUCCIONES. 1. Área de trabajo (1) Mantenga el área de trabajo limpia y bien iluminada. Los banco ...

  • Hitachi D10VG - page 36

    36 Español (3) Evite la puesta en marcha accidental. Cerciórese de que la alimentación de la herramienta eléctrica esté desconectada antes de enchufarla en una toma de la red. Si lleva la herramienta eléctrica con el dedo colocado en el interruptor, o si la enchufa con dicho interruptor cerrado, es posible que se produzcan accidentes. (4) Qui ...

  • Hitachi D10VG - page 37

    37 Español NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD 1. Sujete las herramientas por las superficies de empuñadura aisladas cuando realice una operación en la que la herramienta de corte pueda entrar en contacto con cables ocultos o con su propio cable de alimentación. El contacto con un conductor “activo” “activará” las partes metá ...

  • Hitachi D10VG - page 38

    38 Español 11. Mantenga todos los tornillos, pernos, y cubiertas firmemente fijados en su lugar. Mantenga todos los tornillos, pernos, y cubiertas firmemente montados. Compruebe periódicamente su condición. 12. No utilice herramientas eléctricas si la carcasa o la empuñadura de plástico está rajada. Las rajas en la carcasa o en la empuñadur ...

  • Hitachi D10VG - page 39

    39 Español AISLAMIENTO DOBLE PARA OFRECER UNA OPERACIÓN MÁS SEGURA Para garantizar una operación más segura de esta herramienta eléctrica, HITACHI ha adoptado un diseño de aislamiento doble. “Aislamiento doble” significa que se han utilizado dos sistemas de aislamiento físicamente separados para aislar los materiales eléctricamente con ...

  • Hitachi D10VG - page 40

    40 Español DESCRIPCIÓN FUNCIONAL NOTA: La información contenida en este Manual de instrucciones ha sido diseñada para ayudarle a utilizar con seguridad y mantener esta herramienta eléctrica. NUNCA haga funcionar ni efectúe el mantenimiento de la herramienta antes de leer y comprender todas las instrucciones de seguridad contenidas en este man ...

  • Hitachi D10VG - page 41

    41 Español SPECIFICATIONS Modelo D10VF D10VG D13VF D13VG Motor Motor conmutador en serie monofásico Fuente de alimentación 120V CA, 60 Hz, monofásica Currient 9,0A Velocidad de marcha en vacío 0-3000/min. 0-1200/min. 0-850/min. 0-600/min. Capacidad del portabrocas 3/8" (10mm) 1/2" (13mm) Freno eléctrico No No Sí Sí Capacidad Acero ...

  • Hitachi D10VG - page 42

    42 Español MONT AJE Y OPERACIÓN APLICACIONES 䡬 Por acción de orificios en metal, madera y plástico. ANTES DE LA OPERACIÓN 1. Fuente de alimentación Cerciórese de que la fuente de alimentación que vaya a utilizar cumpla los requisitos indicados en la placa de características del producto. 2. Interruptor de alimentación Cerciórese de que ...

  • Hitachi D10VG - page 43

    43 Español 7. Montaje y desmontaje de la broca Para portabrocas con llave (Fig.2) (1) Abra las mordazas del portabrocas e inserte la broca en el portabrocas. (2) Coloque la llave del portabrocas en cada uno de los tres orificios del portabrocas, y gírela en el sentido de las agujas del reloj (visto desde el lado delantero). Apriete firmemente. (3 ...

  • Hitachi D10VG - page 44

    44 Español 9. Verifique la dirección de rotación (Fig. 7). La broca gira en el sentido de las agujas del reloj (visto desde el lado trasero) empujando el lado R del botón. Si empuja el lado L del botón, la broca girará en sentido contrario a las agujas del reloj. (Las marcas L y R están provistas en el cuerpo). 10. Fijación de la unidad ang ...

  • Hitachi D10VG - page 45

    45 Español 䡬 Para accionar la unidad angular a baja velocidad, fije el portabrocas en el husillo de la unidad angular sobre el lado marcado “LOW” y apriete el tornillo de fijación. En este ajuste, la velocidad de taladrado disminuye a aprox. 70% y el par de taladrado aumenta a aprox. 150% (Fig.10). 䡬 Para operar la unidad angular a alta v ...

  • Hitachi D10VG - page 46

    46 Español 11. Fijación del gancho. (Accesorio opcional) (Fig.14) Para fijar el gancho, es necesario desarmar la parte del asa que cubre el sistema eléctrico de la herramienta. Para poder utilizar la herramienta en condiciones de seguridad y evitar las descargas eléctricas, la instalación del gancho de este taladro debe ser realizado SÓLO por ...

  • Hitachi D10VG - page 47

    47 Español PRECAUCIÓN 䢇 Debido a la reacción generada al funcionar el freno, asegúrese de sostener el taladro firmemente. 䢇 Cuando el freno se vuelve ineficaz, envíe la herramienta a un CENTRO DE SERVICIO AUTORIZADO HITACHI. 3. Taladrado 䡬 Para taladrar, inicie el taladro lentamente, y aumente gradualmente la velocidad. 䡬 Siempre apliq ...

  • Hitachi D10VG - page 48

    48 Español MANTENIMIENTO E INSPECCIÓN ADVERTENCIA: Antes de realizar el mantenimiento o la inspección de la amoladora, cerciórese de desconectar la alimentación y de desenchufar el cable de alimentación del tomacorriente. 1. Inspección de la broca de taladro El uso continuado de una broca de taladreficiencia de taladrar y puede sobrecargar s ...

  • Hitachi D10VG - page 49

    49 Español ACCESORIOS ADVERTENCIA: UTILICE únicamente repuestos y accesorios autorizados por HITACHI. No utilice nunca repuestos o accesorios no previstos para usar con esta herramienta. Si tiene dudas en cuanto a la seguridad de usar determinado repuesto o accesorio junto con su herramienta, póngase en contacto con HITACHI. La utilización de o ...

  • Hitachi D10VG - page 50

    50 ...

  • Hitachi D10VG - page 51

    51 ...

  • Hitachi D10VG - page 52

    WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construc- tion activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● Lead from lead-based paints, ● Crystalline silica from bricks and cement and other mas ...

Manufacturer Hitachi Category Cordless Drill

Documents that we receive from a manufacturer of a Hitachi D10VG can be divided into several groups. They are, among others:
- Hitachi technical drawings
- D10VG manuals
- Hitachi product data sheets
- information booklets
- or energy labels Hitachi D10VG
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hitachi D10VG.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hitachi D10VG, service manual, brief instructions and user manuals Hitachi D10VG. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hitachi D10VG.

Similar manuals

A complete manual for the device Hitachi D10VG, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hitachi D10VG by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hitachi D10VG.

A complete Hitachi manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hitachi D10VG - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hitachi D10VG, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hitachi D10VG, that we can find in the current document
3. Tips how to use the basic functions of the device Hitachi D10VG - which should help us in our first steps of using Hitachi D10VG
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hitachi D10VG
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hitachi D10VG in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hitachi D10VG?

Use the form below

If you did not solve your problem by using a manual Hitachi D10VG, ask a question using the form below. If a user had a similar problem with Hitachi D10VG it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)