Manual Fujitsu 2000

42 pages 0.38 mb
Download

Go to site of 42

Summary
  • Fujitsu 2000 - page 1

    DESKPOWER 2000 Series User’s Manual Fujitsu endeavours to ensure that the infor mation in this document is corr ect, but accepts no liability for any er ror or omission in the same. Any procedures described in this document for operating Fujitsu pr oducts should be read and understood by the operator befor e such pr oducts are used. T o ensur e t ...

  • Fujitsu 2000 - page 2

    IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions carefully. Save these instructions for future reference. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this product near w ...

  • Fujitsu 2000 - page 3

    13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally when the operating instr ...

  • Fujitsu 2000 - page 4

    ■ Conventions used in this manual ● Warning icons Various icons and icon/word combinations are used in this manual. They are used to encourage you to use the equipment safely and correctly in order to prevent danger and damage that may occur to you and people around you. The following paragraphs describe what each icon looks like and what it me ...

  • Fujitsu 2000 - page 5

    ● Conventions used in the text of the manual The symbols used in the text of the manual have meanings as explained below: Information necessary to run hardware or software correctly. Information on how to undo an incorrect operation or how to carry out troubleshooting. ● Screen display examples Screen displays given in this manual are examples. ...

  • Fujitsu 2000 - page 6

    ■ Warning and caution labels Your PC bears the warning and caution labels as shown below. Never detach or soil the warning or caution labels. ● Rear surface of the equipment Electric shock W ARNING ● Before starting to mount or dismount an optional unit for your PC, switch off the PC and all units linked to it, and unplug them from their resp ...

  • Fujitsu 2000 - page 7

    Chapter 1 Installation and Connection This chapter describes what precautions you should take when installing your PC and explains how to connect cables. Before starting to assemble the PC, read this chapter. Chapter 2 Basic Operations This chapter explains basic operations required to use the PC, such as how to switch on and off the power and hand ...

  • Fujitsu 2000 - page 8

    Content CHAPTER 1 Installation and Connectioon Where to install ................................................................... 2 Example of installing the PC ............................................... 2 Prev enting electromagnetic interference with a TV and r adio ........................................................................... ...

  • Fujitsu 2000 - page 9

    CHAPTER 3 Installing Internal Options Installation Precautions .................................................... 20 ESD Precautions .............................................................. 20 Pre-installation Instructions .............................................. 20 P ost-installation Instr uctions .................................... ...

  • Fujitsu 2000 - page 10

    CHAPTER 1 Installation and Connection 03Carrol(1-6) 17/06/2000, 13:49 1 ...

  • Fujitsu 2000 - page 11

    2 1 Installation This section describes counter measures that should be observed when installing and using your PC. ■ Where to install Avoid: - Any area exposed to moisture, dust, and greasy fumes - Poorly ventilated areas - Areas where an open flame is present - Bathrooms, shower room, and any other area where water may splash on the PC - Areas ...

  • Fujitsu 2000 - page 12

    3 ■ Preventing electromagnetic interference with a TV and radio Your PC complies with the FCC Standard restricting electromagnetic interference with TV and radio. However, it may cause interference with a TV and radio near it, depending on where they are installed. Even in this case, the PC is not defective. To keep your PC from interfering with ...

  • Fujitsu 2000 - page 13

    4 2 Connection WARNING ● If your device requires grounding, be sure to ground it correctly before supplying power to the equipment. Operating the device while it is improperly grounded may lead to an electric shock. Never connect the grounding wire to a gas pipe. Failure to observe this precaution may result in fire. ● Before starting to attach ...

  • Fujitsu 2000 - page 14

    5 ■ Attaching CRT display unit, keyboard, mouse, and LAN cables Note the following The connection explained on this page supplies power to the CRT display unit from the PC main unit. In this case, the power cord supplied along with the CRT display unit is not used. Connect the CRT cable to the PC main unit. Attach the CRT cable connector to the C ...

  • Fujitsu 2000 - page 15

    6 ■ Connecting the power cord After connecting the CRT display unit and other peripherals to the PC main unit, connect the power cord of the PC main unit to a wall outlet while observing the following precautions. - Do not plug or unplug the power cord while your hands are wet. - Do not abuse or remodel the power cord. - Do not put heavy objects ...

  • Fujitsu 2000 - page 16

    CHAPTER 2 Basic Operation 04Carrol(7-18) 17/06/2000, 13:49 7 ...

  • Fujitsu 2000 - page 17

    8 This section explains how to switch on the power to your PC. CAUTION ● Once you have switched on the power, do not move any equipment from one place to another or subject it to shock and/or vibration. Failure to heed this precaution may result in malfunction of the device. 1 Press the power switch of the CRT display. At this point, nothing is d ...

  • Fujitsu 2000 - page 18

    9 This section explains how to switch off the power for your PC. Note the following - Before switching off the power, exit all applications and save all necessary data. - Before switching off the power, make sure that the access indicator LEDs of the floppy and hard disk drives are off. If the power is switched off when the access indicator LEDs ar ...

  • Fujitsu 2000 - page 19

    10 ■ Switching off the power via Windows NT (on Windows NT models) This section explains how to switch off the power for the PC via Windows NT. 1 Click [Start]. The "Start" menu appears. 2 Click [Shut Down]. The following dialog box appears. 3 Select "Shut down the computer?" and click [Yes]. Turn off the power switch. Note th ...

  • Fujitsu 2000 - page 20

    11 ■ Switching off the power via Windows 2000 (on Windows 2000 models) This section explains how to switch off the power for the PC via Windows 2000. 1 Click [Start]. The "Start" menu appears. 2 Click [Shut Down]. The following dialog box appears. 3 Select "Shut down" and click [OK]. Note the following The following procedure ...

  • Fujitsu 2000 - page 21

    12 3 Reset This section explains how to reset the PC. Note the following Resetting the PC causes temporary data to be lost from memory. Before resetting, save all necessary data. ■ Soft reset A soft reset initializes only the CPU. It is used when part of POST, such as memory test, is to be omitted, or after software installation. ● Resetting vi ...

  • Fujitsu 2000 - page 22

    13 Note the following The following procedure can also be used to reset the PC: 1 Press [Ctrl]+[Alt]+[Delete]. The "Windows NT Security" dialog box appears. 2 Click [Shut Down]. The "Shut Down Computer" dialog box appears. 3 Select "Restart the computer after shut down?" and click [Yes]. The PC is reset. ● Resetting ...

  • Fujitsu 2000 - page 23

    14 A floppy disk is a storage medium used to save programs and other information. This section explains how to handle floppy disks, including inserting a floppy disk into the drive and removing it. ■ Handling precautions To protect floppy disks and the drive, observe the following don'ts: - Do not splash any liquid such as coffee over a flop ...

  • Fujitsu 2000 - page 24

    15 Your PC incorporates a CD-ROM drive ( PC model with CD-ROM drive installed). This section explains how to handle CD-ROM disks, including inserting a CD-ROM disk into the drive and taking it out. ■ Handling precautions To protect CD-ROM disks and the drive, observe the following don'ts: - Do not write to the label side (printed side) of a ...

  • Fujitsu 2000 - page 25

    16 ■ Inserting and taking out a CD-ROM disk ● Inserting a CD-ROM 1 Press the EJECT button. The CD-ROM tray extends from the drive. 2 With the label side of the CD-ROM disk facing up, place the CD-ROM disk on the tray at the center. 3 Press the EJECT button. The tray retracts into the drive, and the CD-ROM is set. Note the following When the CD- ...

  • Fujitsu 2000 - page 26

    17 Your PC has a built-in hard disk. This section describes cautions to be observed when using the hard disk. ■ What is the hard disk? A hard disk drive is a unit to save software and other information. It consists of a disk packed in a box as shown to the right. The hard disk can save a larger amount of information, and read and write at higher ...

  • Fujitsu 2000 - page 27

    CHAPTER 3 Installing Internal Options 05Carrol(19-24) 17/06/2000, 13:49 19 ...

  • Fujitsu 2000 - page 28

    20 ■ Installation Precautions Before you install any system component, we recommend that you read the following sections. These sections contain important ESD precautions, pre- and post installation instructions. ■ ESD Precautions Electrostatic discharge (ESD) can damage your processor, disk drives, expansion boards, and other components. Alway ...

  • Fujitsu 2000 - page 29

    21 ■ Post-installation Instructions Observe the following after installing a system component: 1 See to it that the components are installed according to the step-by-step instructions in their respective sections. 2 Make sure you have set all the required jumpers. 3 Replace any expansion boards or peripherals that you removed earlier. 4 Replace t ...

  • Fujitsu 2000 - page 30

    22 2 DRAM Installation The mainboard can be installed with 64 / 128 / 256 MB 168 pins DIMM module DRAM, and the DRAM speed must be 100 MHz for SDRAM. The DRAM memory system on mainboard consists of bank 0 & bank 1. Since 168 pins DIMM module is 64 bits width, using 1 PCS which can match a 64 bits system. The total memory size is 512MB SDRAM. In ...

  • Fujitsu 2000 - page 31

    23 3 Installing Expansion Card ■ Installing an expansion card To install an expansion card, follow the steps below: 1 Remove the side cover. 2 Remove the bracket on the housing opposite to the empty PCI slot. 3 Install the expansion card on the connector. Fit the expansion card into the connector firmly. 4 Fasten with the screw. Fasten the expans ...

  • Fujitsu 2000 - page 32

    CHAPTER 4 Troubleshooting 06Carrol(25-28) 17/06/2000, 13:49 25 ...

  • Fujitsu 2000 - page 33

    26 This section describes the trouble information of some functions. Read the necessary part. For the trouble information related to Windows NT, see the Windows NT manual supplied with the PC and the online help that can be accessed from the "Start" menu. ■ Trouble information related to the PC main body and peripheral equipment ● The ...

  • Fujitsu 2000 - page 34

    27 ● The PC does not turn on. The power lamp in the front face does not go on. Check whether the power cable is connected to an outlet. ● Data cannot be read from the CD-ROM drive. Check the following: - Check whether the CD-ROM disk is placed at the center of the tray. Place the CD-ROM disk with the label side up. - Ensure the CD-ROM disk is n ...

  • Fujitsu 2000 - page 35

    28 If you cannot find out the cause of a problem or cannot fix a problem, contact your local distributor or your local Fujitsu service centre. Before making a help call, check the following and prepare a memo so that you can give correct information to a maintenance person. - Model and type of the PC (indicated on the label in the rear face of the ...

  • Fujitsu 2000 - page 36

    APPENDIX 07Carrol(29-33) 17/06/2000, 13:50 29 ...

  • Fujitsu 2000 - page 37

    30 Floppy disk eject button When you take out a floppy disk, press this button. Do not press the button while the floppy disk access indicator light is on. Floppy disk drive (for 3.5-inch disks) The drive is used to read data from or write it to a floppy disk. This section describes the name and function of each component of the system unit, mother ...

  • Fujitsu 2000 - page 38

    31 Power switch When you turn on or off the system unit, press this switch. CD-ROM drive (only in CD-ROM drive-equipped model) The drive is used to start up CD-ROM applications, or play music CDs. File bays These bays can house a 5-inch or 3.5-inch floppy disk drive, internal hard disk, internal magneto-optical disk drive. Hard disk access indicato ...

  • Fujitsu 2000 - page 39

    32 ■ Back of the system unit USB connector A peripheral device conforming to USB plugs into this connector. Parallel connector (PRINTER) The printer cable plugs into this connector. CRT connector The CRT cable plugs into this connector. AUDIO OUT Headphone / Line Output AUDIO IN Line Input MICROPHONE Jack Microphone Input Keyboard connector (KEYB ...

  • Fujitsu 2000 - page 40

    33 Power "Out" socket The CRT power cable plugs into this socket. Ventilation holes The heat created inside the system unit is let out through these holes. Power "In" socket The power cable of the system unit plugs into this socket. Mouse connector (MOUSE) The mouse cable plugs into this connector. MIDI / GAMEPORT 07Carrol(29-33 ...

  • Fujitsu 2000 - page 41

    34 ■ System unit specifications 2 Standard Specifications Product name CPU Flash ROM System RAM Floppy disk Hard disk CD-ROM Graphics I/F CRT USB Keyboard Mouse Serial port Parallel port Number of extension slots Number of storage bays Power supply/frequency Power consumption Weight Dimensions Operating environment DESKPOWER 2000 Intel Pentium II ...

  • Fujitsu 2000 - page 42

    35 Fujitsu PC (Asia) Pte Ltd 200 P andan Loop #05-03 P antech 21 The Computer Centre Singapore 128388 T el: 65-776 0688 F ax: 65-776 0788 Fujitsu PC (Asia) Pte Ltd (Malaysia Br anch) 8th Floor Wisma Damansara Jalan Semantan 50490 K uala Lumpur Mala ysia T el: 603-253 3997 F ax: 603-253 4245 Website : www.fujitsu-pc-asia.com 08Carrol(34-35) 17/06/20 ...

Manufacturer Fujitsu Category Personal Computer

Documents that we receive from a manufacturer of a Fujitsu 2000 can be divided into several groups. They are, among others:
- Fujitsu technical drawings
- 2000 manuals
- Fujitsu product data sheets
- information booklets
- or energy labels Fujitsu 2000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Fujitsu 2000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Fujitsu 2000, service manual, brief instructions and user manuals Fujitsu 2000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Fujitsu 2000.

Similar manuals

A complete manual for the device Fujitsu 2000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Fujitsu 2000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Fujitsu 2000.

A complete Fujitsu manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Fujitsu 2000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Fujitsu 2000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Fujitsu 2000, that we can find in the current document
3. Tips how to use the basic functions of the device Fujitsu 2000 - which should help us in our first steps of using Fujitsu 2000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Fujitsu 2000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Fujitsu 2000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Fujitsu 2000?

Use the form below

If you did not solve your problem by using a manual Fujitsu 2000, ask a question using the form below. If a user had a similar problem with Fujitsu 2000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)