Manual Garmin HN294DP/DI

104 pages 1.32 mb
Download

Go to site of 104

Summary
  • Garmin HN294DP/DI - page 1

    ADSL Wireless Router HN294dp/di User Guide ...

  • Garmin HN294DP/DI - page 2

    ADSL Wireless Router HN294dp/di User Guide . ii EN/LZT 108 6377 R4 – Septemb er 2003 Copyright  Ericsson AB – 2003 All Rights Reserved Disclaimer The contents of this document are subject to revision without notice due t o continued progress in methodology, design, and manufacturing. Ericsson shall have no liability for any error or damages ...

  • Garmin HN294DP/DI - page 3

    Contents EN/LZT 108 3377 R4 – Septemb er 2003 iii Contents 1 Introduction 1 1.1 About this User Guide 1 1.2 About the ADSL Wireless Router HN294d 1 1.2.1 Ease of Use 2 1.2.2 Wireless Features 2 1.2.3 Security 3 1.2.4 Advanced Possibilities 4 2 Hardware Description and Installation 5 2.1 Before You Start 5 2.1.1 Package Contents 5 2.1.2 Subscripti ...

  • Garmin HN294DP/DI - page 4

    Contents iv EN/LZT 108 6377 R4 - Septembe r 2003 4.2 IP Addresses Assigned by PPPoE 20 4.3 IP Addresses Assigned by DHCP 21 4.4 Static IP Addresses 21 5 ADSL-mode – RFC1483 Router 22 5.1 Description 22 5.2 IP Addresses Assigned by DHCP 22 5.3 Static IP Addresses 23 6 ADSL-mode – RFC1483 MER Router 24 6.1 Description 24 6.2 IP Addresses Assigned ...

  • Garmin HN294DP/DI - page 5

    Contents EN/LZT 108 6377 R4 - Septembe r 2003 v 9.4.6 Reset Router 39 9.5 Status 41 9.5.1 DSL Connection 41 9.5.2 WAN Connection 42 9.5.3 Traffic Counter 43 9.5.4 Routing Table 44 9.5.5 DHCP Table 44 9.5.6 Wireless Client 44 9.6 Configuration 46 9.6.1 DSL Configuration 46 9.6.2 LAN Configuration 46 9.6.3 WLAN Configuration 51 9.6.4 WAN Configuratio ...

  • Garmin HN294DP/DI - page 6

    Contents vi EN/LZT 108 6377 R4 - Septembe r 2003 11.2.1 License 81 11.2.2 Term 81 11.2.3 Limited Warranty 81 11.2.4 Intended Use 82 11.2.5 Limitation of Liability 82 11.2.6 Governing Law 82 11.3 Regulatory Information 83 11.3.1 EU Directives 83 11.3.2 Safety Approvals 83 11.3.3 EMC Approvals 84 11.3.4 Telecom Approval 85 11.3.5 Access Point Frequen ...

  • Garmin HN294DP/DI - page 7

    Introduction EN/LZT 108 6377 R4 - Septembe r 2003 1 1 Introduction 1.1 About this User Guide This User Guide provides general information about the installation of the Ericsson ADSL Wireless Router HN294d, as well as information about configuration possibilities. The following chapters are included in this guide:  Chapter 1 – “Introduction? ...

  • Garmin HN294DP/DI - page 8

    Introduction 2 EN/LZT 108 6377 R4 - Septembe r 2003 HN294d is a powerful addition to your home; HN294d stands for Ericsson quality, Wireless (WLAN) stands for freedom from cables, ADSL stands for high-speed access to the Internet, Router stands for security/convenience and they altogether stands for the future. The HN294d is available in two versio ...

  • Garmin HN294DP/DI - page 9

    Introduction EN/LZT 108 6377 R4 - Septembe r 2003 3 find the HN294d and assign your computer an IP address. Now, you are ready to surf and use the Internet anywhere in your home. Since a wireless network is more vulnerable to attacks than a traditional wired network it is recommended to make some configuration that will make it impossible for anoth ...

  • Garmin HN294DP/DI - page 10

    Introduction 4 EN/LZT 108 6377 R4 - Septembe r 2003 tunnel where the information inside the tunnel is encrypted so that only the intended target at the end of the tunnel can read the information. 1.2.4 Advanced Possibilities The HN294d also offers sophisticated router functionality making it possible for advanced users to create customized network ...

  • Garmin HN294DP/DI - page 11

    Hardware Description and Instal lation EN/LZT 108 6377 R4 - Septembe r 2003 5 2 Hardware Description and Installation This chapter provides a hardware description of the product a nd detailed instructions about how to install the HN294d in a PC/Windows environment. 2.1 Before Y ou S tart 2.1.1 Package Contents Check the contents of the package agai ...

  • Garmin HN294DP/DI - page 12

    Hardware Description and Instal lation 6 EN/LZT 108 6377 R4 - Septembe r 2003  ADSL Line Cable  Ethernet Cable  USB Cable  Quick Installation Guide Your HN294d package may also include other materials provided by your ADSL operator. 2.1.2 Subscription for ADSL Service To use the ADSL Wireless Router HN294d, you will require an ADSL serv ...

  • Garmin HN294DP/DI - page 13

    Hardware Description and Instal lation EN/LZT 108 6377 R4 - Septembe r 2003 7 Symbol Status/Description WLAN Unlit : Power Off or no radio signal (WLAN card is not present or fails to function). Blinking : Traffic is going through the WLAN interface. Solid : The Wireless LAN interface is ready. DSL Unlit : Power Off. Blinking : ADSL line connection ...

  • Garmin HN294DP/DI - page 14

    Hardware Description and Instal lation 8 EN/LZT 108 6377 R4 - Septembe r 2003  POWER button – To power ON/OFF your HN294d.  PWR – The PWR socket is used for connecting the supplied power supply adapter. 2.3 Choose a Place for the Router The HN294d can be mounted on the wall or simply placed on a flat surface. NOTE! Proper ventilation is n ...

  • Garmin HN294DP/DI - page 15

    Hardware Description and Instal lation EN/LZT 108 6377 R4 - Septembe r 2003 9 2.4 Connect the HN294d This chapter describes how to connect the HN294d to your Wireless LAN and/or to your LAN computer(s) using the Ethernet and/or USB interface(s). 2.4.1 Connect Wireless Computer(s) To be able to communicate with the HN294d in a wireless LAN your comp ...

  • Garmin HN294DP/DI - page 16

    Hardware Description and Instal lation 10 EN/LZT 108 637 7 R4 - September 2003 wireless MAC address (can be found on an information sticker on the bottom of the router). 6. Now, the HN294d must be configured for your specific ADSL mode and other settings. This is described in chapter 3 “Initial Configuration”. 2.4.2 Connect Computer(s) via Cabl ...

  • Garmin HN294DP/DI - page 17

    Hardware Description and Instal lation EN/LZT 108 6377 R4 - Septembe r 2003 11 The LAN and/or USB LED(s) turn On indicating a proper connection to either a Ethernet NIC or a USB port. 5. Now, the HN294d must be configured for your specific ADSL mode and other settings. This is described in chapter 3 – “Initial Configuration”. 2.4.2.1 Install ...

  • Garmin HN294DP/DI - page 18

    Hardware Description and Instal lation 12 EN/LZT 108 637 7 R4 - September 2003 3. Select Install USB Driver and wait until the following window is displayed: 4. Click Next> . Files will now be copied to your hard disk and w hen completed the following window appears: 5. Connect the provided USB cable to the USB port of your HN294d. Connect the o ...

  • Garmin HN294DP/DI - page 19

    Hardware Description and Instal lation EN/LZT 108 6377 R4 - Septembe r 2003 13 NOTE! If the Digital Signature Not Found window (or similar) appears, you should click Yes (or Continue Anyway ) to continue the installation. This is a warning from Microsoft that the installation software is not a digitally signed version, but sin ce Ericsson has teste ...

  • Garmin HN294DP/DI - page 20

    Hardware Description and Instal lation 14 EN/LZT 108 637 7 R4 - September 2003 2.5 Configure Client PCs This chapter describes how you can check (and maybe change) the TCP/IP settings in your computer(s) if you have problems to access the Internet. Refer to information from your Internet Service Provider. 2.5.1 Use DHCP If you have not been provide ...

  • Garmin HN294DP/DI - page 21

    Hardware Description and Instal lation EN/LZT 108 6377 R4 - Septembe r 2003 15 7. Close the “Network and Internet Connections” window. In Windows XP: 1. From the Start menu select Control Panel and double-click on Network Connections (Classic View) or double-click on the link Network and Internet connections followed by Network Connections (Cat ...

  • Garmin HN294DP/DI - page 22

    Hardware Description and Instal lation 16 EN/LZT 108 637 7 R4 - September 2003 6. Some configuration files may be copied to your hard disk and if a “Settings Changes” message asks you to restart your PC, you should answer Yes . In Windows 2000: 1. From the Start menu select Settings > Control Panel and double- click on the Network and Dial-u ...

  • Garmin HN294DP/DI - page 23

    Initial Configuration EN/LZT 108 6377 R4 - Septembe r 2003 17 3 Initial Configuration This chapter describes how to access the built-in Configuration tool and r un the Configuration Wizard in order to perform the initial configuration. 3.1 Introduction The HN294d is an advanced ADSL router with several features and supported modes that make it idea ...

  • Garmin HN294DP/DI - page 24

    Initial Configuration 18 EN/LZT 108 637 7 R4 - September 2003 The HN294 still offers the possibility for advanced users to set up special network scenarios themselves or to modify the existing ones. Refer to the “Advanced Configuration” chapter for further information. TIP : For advanced network scenarios, select the ADSL-mode that is closest t ...

  • Garmin HN294DP/DI - page 25

    Initial Configuration EN/LZT 108 6377 R4 - Septembe r 2003 19 4. The welcome page of the Configuration tool is displayed: 5. Click on the Configuration Wizard button and follow the instructions given on-screen. 6. When you have completed the wizard and reached the last page (step 4) it is important that you click the Save Configuration button to sa ...

  • Garmin HN294DP/DI - page 26

    ADSL-mode – RFC1483 Bridge 20 EN/LZT 108 637 7 R4 - September 2003 4 ADSL-mode – RFC1483 Bridge 4.1 Description RFC1483 (2684) Bridged Mode (single PVC) In this mode the HN294d will act only as a “bridge”, meaning that the routing functionality (firewall, NAT, UPnP, etc) will be disabled. This mode is suitable when you only want to connect ...

  • Garmin HN294DP/DI - page 27

    ADSL-mode – RFC1483 Bridge EN/LZT 108 6377 R4 - Septembe r 2003 21 4.3 IP Addresses Assigned by DHCP The PCs on the LAN/WLAN use the DHCP protocol. The IP addresses are dynamically assigned to the PCs from t he DHCP server at the ISP. Verify that your TCP/IP settings are set to “Obtain an IP address automatically”. Refer to section xxx “Use ...

  • Garmin HN294DP/DI - page 28

    ADSL-mode – RFC1483 Router 22 EN/LZT 108 637 7 R4 - September 2003 5 ADSL-mode – RFC1483 Router 5.1 Description RFC1483 (2684) Routed Mode (single PVC) The RFC1483 Router mode allows a simple routed connection to the Internet. This ADSL-mode can also be used together with NAT to let the end-user connect an almost unlimited number of PCs on the ...

  • Garmin HN294DP/DI - page 29

    ADSL-mode – RFC1483 Router EN/LZT 108 6377 R4 - Septembe r 2003 23 “Obtain an IP address automatically”. Refer to section xxx “Use DHCP” for instructions. 5.3 S tatic IP Addresses The PCs on the LAN/WLAN are manually configured with static IP addresses provided by your ISP/service provider. Refer to section xxx “Use Static IP Addresses? ...

  • Garmin HN294DP/DI - page 30

    ADSL-mode – RFC1483 MER Router 24 EN/LZT 108 637 7 R4 - September 2003 6 ADSL-mode – RFC1483 MER Router 6.1 Description RFC1483 (2684) Bridged Mode (single PVC) with router functionality enabled . A new feature of the HN294d is bridge-router mode. In this mode the user can connect an almost unlimited number of PCs to the LAN/WLAN but still only ...

  • Garmin HN294DP/DI - page 31

    ADSL-mode – RFC1483 MER Router EN/LZT 108 6377 R4 - Septembe r 2003 25 PCs on the LAN/WLAN will be assigned private IP addresses from the built- in DHCP server and the NAT will route the traffic to/from the WAN. The HN294d offers several automatic features (such as ALG, Smart tracking, UPnP, Firewall etc) to make Internet surfing, downloading fil ...

  • Garmin HN294DP/DI - page 32

    ADSL-mode – PPPoE Router 26 EN/LZT 108 637 7 R4 - September 2003 7 ADSL-mode – PPPoE Router 7.1 Description This ADSL-mode, much like the “RFC1483 MER Router” mode, allows the user to connect an almost unlimited number of PCs on the LAN/WLAN with only one IP address from the ISP. All traffic from the LAN/WLAN uses the same PVC. NOTE! This A ...

  • Garmin HN294DP/DI - page 33

    ADSL-mode – PPPoE Router EN/LZT 108 6377 R4 - Septembe r 2003 27 7.2 PPPoE T ermination and PPPoE Passthrough The “PPPoE Router” mode also allows user to connect directly from the PC to the BRAS at the ISP. This means that the user can choose if he/she wants to use the built-in PPPoE client, a PPPoE client installed on the PC, or a combinatio ...

  • Garmin HN294DP/DI - page 34

    ADSL-mode – PPPoA Router 28 EN/LZT 108 637 7 R4 - September 2003 8 ADSL-mode – PPPoA Router 8.1 Description This ADSL-mode, much like the “RFC1483 MER Router” mode, allows the user to connect an almost unlimited number of PCs on the LAN/WLAN with only one IP address from the ISP. All traffic from the LAN/WLAN uses the same PVC. NOTE! This A ...

  • Garmin HN294DP/DI - page 35

    ADSL-mode – PPPoA Router EN/LZT 108 6377 R4 - Septembe r 2003 29 8.2 IP Addresses Assigned by DHCP The PCs on the LAN/WLAN normally use the DHCP protocol. The IP addresses are dynamically assigned to t he PCs from the DHCP server in the HN294d. If DHCP Relay is enabled, the IP addresses can be assigned from a DHCP server at the ISP. Verify that y ...

  • Garmin HN294DP/DI - page 36

    Advanced Configurati on 30 EN/LZT 108 637 7 R4 - September 2003 9 Advanced Configuration 9.1 Introduction The HN294 offers the possibility for advanced users to set up special network scenarios themselves or to modify the existing ones. TIP : For advanced network scenarios, use the Configuration Wizard and select the ADSL-mode that is closest to yo ...

  • Garmin HN294DP/DI - page 37

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 31 3. Type admin in both the “User name” and “Password” fields that are the default settings for the HN294d, and click OK . 4. The welcome page of the Configuration tool is displayed: 5. Click on the Advanced Configuration button to enter the Web Manager. 9.2.1 Outline of the Web M ...

  • Garmin HN294DP/DI - page 38

    Advanced Configurati on 32 EN/LZT 108 637 7 R4 - September 2003 9.3 Overview This is the start page of the Web Manager: On this page you can see the current configuration of your HN294d. For ADSL-modes that use PPP as connection type, you need to Connect/Disconnect when you want to access the Internet. This is shown in the “Action” column by ei ...

  • Garmin HN294DP/DI - page 39

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 33 1. Click the Connect button in the “Action” column. The following page appears: 2. Enter the User Name and Password provided by your ISP and click on the Connect button. 3. Once the connection is successfully established you will return to the Overview page where you can keep track ...

  • Garmin HN294DP/DI - page 40

    Advanced Configurati on 34 EN/LZT 108 637 7 R4 - September 2003 9.4 System 9.4.1 Device Information The System > Device Info page provides a general overview of your HN294d including the hardware board, firmware version, and information about the Ethernet, USB and Wireless interfaces. 9.4.2 Administration 9.4.2.1 Account On the System > Admin ...

  • Garmin HN294DP/DI - page 41

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 35 To change the default User Name and/or Password, just type your new information in the fields. If you only want to change the password, keep admin in the “User Name” field and type your new password (in both fields). Confirm by clicking the Apply button. The login window then appear ...

  • Garmin HN294DP/DI - page 42

    Advanced Configurati on 36 EN/LZT 108 637 7 R4 - September 2003 Select Unlimited time if you always want to have access to your HN294 d from the Internet. 2. Click the Enable button. Information about “Seconds remaining for remote access” is now displayed. 3. In order to disable this function, simply click the Disable button. 4. Select System & ...

  • Garmin HN294DP/DI - page 43

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 37 9.4.3.1 Backup To save a backup file of your current configuration proceed as follows: 1. Click the Backup button. 2. An information window is displayed. Click OK to continue.. 3. Enter a filename (or keep the default MyConfiguration) and select a destination folder where you want to sa ...

  • Garmin HN294DP/DI - page 44

    Advanced Configurati on 38 EN/LZT 108 637 7 R4 - September 2003 4. When the restoring is completed the following window appears: 5. Click the Save button to save the configuration (otherwise the new settings are only valid until next reboot). 9.4.4 Save Configuration From the System > Save Configuration page you can save all current configuratio ...

  • Garmin HN294DP/DI - page 45

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 39 The HN294d supports firmware upgrades via HTTP. To transfer a new firmware file and upgrade the HN294d, follow the steps below: 1. Download and unzip the new firmware file to your local PC. 2. In the File Name of Firmware field, click the Browse button to locate the upgrade file. 3. Cli ...

  • Garmin HN294DP/DI - page 46

    Advanced Configurati on 40 EN/LZT 108 637 7 R4 - September 2003 Click the Restart button. When restarting the system, your browser session will be disconnected. Please wait until the device has finished restarting before attempting to reconnect to the device. 9.4.6.1 Reset to Factory Default If Reset to factory default settings is checked before yo ...

  • Garmin HN294DP/DI - page 47

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 41 9.5 S tatus 9.5.1 DSL Connection The Status > DSL Connection page shows the DSL line connection status: By clicking the Refresh link (above the table) all values will be updated. The table below describes the included parameters: Parameter Description Line Mode The HN294d support s m ...

  • Garmin HN294DP/DI - page 48

    Advanced Configurati on 42 EN/LZT 108 637 7 R4 - September 2003 Parameter Description DS / US Latency Displays whether a fast or interleaved latency path is specified. Trellis coding Indicates if trellis coding is enabled or di sabled. Trellis coding is a method of providing b etter performance in a noisy environm ent. It helps to transmit at faste ...

  • Garmin HN294DP/DI - page 49

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 43 Parameter Description PVC Name The name specified for the specific PVC. VPI Shows the VPI (Virtual Pa th Identifier). Valid range is from 0 to 255. VCI Shows the VCI (Virtual Channel Identifier). Valid range is from 32 to 4095 (1-31 is re served for well- known protocols). Data Encap Sh ...

  • Garmin HN294DP/DI - page 50

    Advanced Configurati on 44 EN/LZT 108 637 7 R4 - September 2003 9.5.4 Routing T able The Status > Routing Table page shows the routing rules of data packets going through the HN294d while in routing mode. By clicking the Refresh link (above the table) all the values will be updated. 9.5.5 DHCP T able The Status > DHCP Table page shows the DHC ...

  • Garmin HN294DP/DI - page 51

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 45 For each wireless client, the MAC Address and the On-Line Time are indicated. By clicking the Refresh link (above the table) all the values will be update d. ...

  • Garmin HN294DP/DI - page 52

    Advanced Configurati on 46 EN/LZT 108 637 7 R4 - September 2003 9.6 Configuration 9.6.1 DSL Configuration The Configuration > DSL page allows you to define the DSL Line Mode. The DSL Line Mode you specify will be applied to the entire HN294d meaning that all ATM PVC provides created will use the same line mode. Consult your ISP/service provider ...

  • Garmin HN294DP/DI - page 53

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 47 9.6.2.1 IP Address On the Configuration > LAN > IP Address page you can define the IP addresses over the LAN interface on which you can access the HN294d. The table below describes the parameters: Parameter Description Primary IP Address The Primary IP address is used for the p ur ...

  • Garmin HN294DP/DI - page 54

    Advanced Configurati on 48 EN/LZT 108 637 7 R4 - September 2003 9.6.2.2 DHCP Server The Configuration > LAN > DHCP Server page allows you to configure the built-in DHCP Server. The HN294d incorporates a DHCP (Dynamic Host Configuration Protocol) server, which dynamically assigns IP addresses and serves as a DNS server to the PCs on the LAN/WL ...

  • Garmin HN294DP/DI - page 55

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 49 The table below describes the parameters: Parameter Description Interface Select the appropriat e interface from the drop -down list. NOTE! “Primary LAN” is the only sele ction in this version. Start IP Address End IP Address Specify the range of IP addresses that can be assigned to ...

  • Garmin HN294DP/DI - page 56

    Advanced Configurati on 50 EN/LZT 108 637 7 R4 - September 2003 Parameter Description Domain Name Servers You can check the Re port this host as the DNS server box to use this host as the default DNS. Or you can uncheck the box and manually set up the DNS IP address in the Primary/Secondary DNS IP address fields. The DNS server addresses will be pa ...

  • Garmin HN294DP/DI - page 57

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 51 9.6.3 WLAN Configuration 9.6.3.1 Basic Setup On the Configuration > WLAN > Basic Setup page you can make some basic security configuration for your Wireless LAN. ...

  • Garmin HN294DP/DI - page 58

    Advanced Configurati on 52 EN/LZT 108 637 7 R4 - September 2003 The table below describes the parameters: Parameter Description Wireless SSID The Wireless SSID (Service Set IDentification) is the name of your wireless netwo rk. The HN294d comes preconfigured with a unique name, HN294- xxxxxx, where xxxxxx is th e last six digits of its wireless MAC ...

  • Garmin HN294DP/DI - page 59

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 53 key mode as well. If you select “Auto”, the HN294d will adapt to each client’s setting, and therefore accept cli ents using both “open system” and cli ents using “shared key” authentication. For maximum security, Shared key mode should be used. Wired Equivalent Privacy Mec ...

  • Garmin HN294DP/DI - page 60

    Advanced Configurati on 54 EN/LZT 108 637 7 R4 - September 2003 NOTE! If you are using a wireless client when configuring WEP, after pressing the Apply button you will not be able to have contact with the router until you have configured your wireless clients as well. This is fully normal and is a proof that your network is now protected. Remember ...

  • Garmin HN294DP/DI - page 61

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 55 00:90:96:1A:2B:3C and only number 0 through 9 and letters a through f are allowed. 2. Click the Apply button and the following page appears: 3. Verify that the correct MAC address is shown in the list of authorized clients. 4. Select System > Save Configuration and click the Save but ...

  • Garmin HN294DP/DI - page 62

    Advanced Configurati on 56 EN/LZT 108 637 7 R4 - September 2003 3. Select System > Save Configuration and click the Save button to save your new settings. To remove a client, simply click Delete in the list of approved clients. 9.6.4 W AN Configuration On the Configuration > WAN page you can create, modify and delete ATM PVC interfaces. The H ...

  • Garmin HN294DP/DI - page 63

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 57 selected: 4. Fill in the parameters according to information from your ISP/service provider and click the Apply button. 5. Select System > Save Configuration and click the Save button to save your new settings. The parameters for creating a new ATM PVC Interface are described below. ...

  • Garmin HN294DP/DI - page 64

    Advanced Configurati on 58 EN/LZT 108 637 7 R4 - September 2003 Parameter Description VCI Identifies the VCI (Virtual Channel Identifier). The valid range is from 32 to 4095 (1 to 31 are reserved for well-known protocols). ATM Service Type Supported ATM Se rvice Types are UBR, CBR, VBR-nrt and VBR-rt. PCR (Peak Cell Rate) Identifies the PCR cells p ...

  • Garmin HN294DP/DI - page 65

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 59 By enabling Al ways On a periodic echo request will be sent to the ISP that pr events the connection from being closed by the ISP. Enable NAT on this interface Select this option if you want to enable NAT (Network Address Tran slation) on the interface. NOTE! When you initially add a PV ...

  • Garmin HN294DP/DI - page 66

    Advanced Configurati on 60 EN/LZT 108 637 7 R4 - September 2003 1. Click the Create a new route button. The following page appears: 2. Enter parameters according to information in the table below and click the Apply button. 3. Select System > Save Configuration and click the Save button to save your new settings. Description of parameters when c ...

  • Garmin HN294DP/DI - page 67

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 61 By default RIP is disabled and you can enable RIP on both the WAN and Primary LAN interfaces. The RIP values can be customized for both Receive and Transmit mode. Receive Mode incorporates the RIP information when receiving RIP packets and Transmit Mode broadcasts the routing table. To ...

  • Garmin HN294DP/DI - page 68

    Advanced Configurati on 62 EN/LZT 108 637 7 R4 - September 2003 To enable DNS Relay or modify the current settings proceed as follows: 1. Select the Enabled radio button and click the Configure button. The following page appears: 2. Specify up to three DNS Server IP addresses and click the Apply button. 3. Select System > Save Configuration and ...

  • Garmin HN294DP/DI - page 69

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 63 9.6.6.2 DNS Server On the Configuration > DNS > Server page you can disable/enable the DNS Server function. If you have established settings before, the page will show a table containing all current DNS clients created. To disable/enable the DNS Server, select the appropriate radi ...

  • Garmin HN294DP/DI - page 70

    Advanced Configurati on 64 EN/LZT 108 637 7 R4 - September 2003 Select System > Save Configuration and click the Save button to save your new settings. 9.6.7 Security 9.6.7.1 Firewall On the Configuration > Security > Firewall page you can select the desired security level for the built-in firewall. To simplify the configuration you can se ...

  • Garmin HN294DP/DI - page 71

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 65 Set an appropriate security level for the firewall and click the Apply button. Select System > Save Configuration and click the Save button to save your new settings. ...

  • Garmin HN294DP/DI - page 72

    Advanced Configurati on 66 EN/LZT 108 637 7 R4 - September 2003 Modify or delete existing rules 1. Select the Advanced (User Define) option and click the Apply button. The following page appears: 2. At the bottom of the page, select between which interfaces you want to modify or delete the existing rules. If you have not created a secondary LAN (se ...

  • Garmin HN294DP/DI - page 73

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 67 3. Click the Modify link next to the rule you want to modify. 4. To delete an existing rule, click the Delete link. NOTE! If you delete any of the predefined entries, the service type of the deleted entry will be blocked. This means that the LAN PCs will not be able to access its corres ...

  • Garmin HN294DP/DI - page 74

    Advanced Configurati on 68 EN/LZT 108 637 7 R4 - September 2003 6. Enter parameters according to the descriptions below and click the Apply button. 7. Select System > Save Configuration and click the Save button to save your new settings. Description of parameters when creating a new filtering rule: Parameter Description Protocol Type It governs ...

  • Garmin HN294DP/DI - page 75

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 69 Parameter Description Port Range Enter the starting and ending port nu mbers that identify the service that you want to filter, e.g. web service is on port 80 and FTP on port 21 . Direction Choose whether to filter the packets that are incoming (In Bound) or out going (Out Bound) with r ...

  • Garmin HN294DP/DI - page 76

    Advanced Configurati on 70 EN/LZT 108 637 7 R4 - September 2003 To modify the existing rules, click the Modify Rules button and the following page appears: Make your changes and click the Apply button. Select System > Save Configuration and click the Save button to save your new settings. 9.6.8 V irtual Server The Configuration > Virtual Serv ...

  • Garmin HN294DP/DI - page 77

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 71 want to make them publicly accessible. With NAT applied, the internal IP addresses of these servers will be translated to a single IP a ddress that is unique on the Internet. The NAT function not only eliminates the need for multiple public IP addresses, but also provides a measure of s ...

  • Garmin HN294DP/DI - page 78

    Advanced Configurati on 72 EN/LZT 108 637 7 R4 - September 2003 3. Select System > Save Configuration and click the Save button to save your new settings. Description of parameters when creating a new virtual server: Parameter Description ATM PVC Name Select the ATM PVC interface from the drop-down list. External Packet Protocol Select the proto ...

  • Garmin HN294DP/DI - page 79

    Advanced Configuration EN/LZT 108 6377 R4 - Septembe r 2003 73 1. Click the Setup DMZ host button and the following page appears: 2. Enter parameters according to the description in the table below and click the Apply button. 3. Select System > Save Configuration and click the Save button to save your new settings. Description of parameters when ...

  • Garmin HN294DP/DI - page 80

    Advanced Configurati on 74 EN/LZT 108 637 7 R4 - September 2003 Select System > Save Configuration and click the Save button to save your new settings. 9.6.10 UPnP On the Configuration > UPnP page you can enable the UPnP function. Universal plug and play (UPnP) is a networking architecture that provides compatibility among networking equipmen ...

  • Garmin HN294DP/DI - page 81

    Troubleshooting EN/LZT 108 6377 R4 - Septembe r 2003 75 10 Troubleshooting This chapter provides tips and solutions for resolving some of the proble ms you might encounter when using your HN294d. If the suggested solutions do not resolve your issue, contact your system administrator or Internet Service Provider. 10.1 Basic Functions Indication/Symp ...

  • Garmin HN294DP/DI - page 82

    Troubleshooting 76 EN/LZT 108 637 7 R4 - September 2003 10.2.1 How to use WINIPCFG Use WINIPCFG if your PC is running Windows 95, 98 or Me: 1. From the Start menu select Run… . 2. Type wini pc fg and click OK . The “IP Configuration” dialog b ox appears. 3. From the scroll down menu at the top, select the network card that you are using. This ...

  • Garmin HN294DP/DI - page 83

    Troubleshooting EN/LZT 108 6377 R4 - Septembe r 2003 77 10.3 W AN Connection Indication/Symptom What to do I can access the HN294d but cannot connect to my ISP. Make sure that the HN294 d is connected prop erly according to the installation instructions. If the DSL LED on the front panel is Off or keeps flashing, there may be a problem with the cab ...

  • Garmin HN294DP/DI - page 84

    Troubleshooting 78 EN/LZT 108 637 7 R4 - September 2003 Bluetooth devices, microwave ovens and 2.4 GHz cordless phones might interfere with yo ur wireless LAN. Furthermore, you may want to consid er repositioning the HN294d (e.g. wall mou nt it). 10.5 Reset the HN294d Failure to access your HN294d may occur if the router is configured incorrectly o ...

  • Garmin HN294DP/DI - page 85

    Troubleshooting EN/LZT 108 6377 R4 - Septembe r 2003 79 3. In the File Name of Firmware field, click the Browse button to locate the upgrade file. 4. Click the Upgrade button. DO NOT turn off your HN294d during the firmware upgrade. The process may take a while due to extensive testing of the software. After upgrading, the original configuration se ...

  • Garmin HN294DP/DI - page 86

    Important Infor mation 80 EN/LZT 108 637 7 R4 - September 2003 11 Important Information 11.1 Product Care and Maintenance NOTE! These are important guidelines for safe and efficient use of your device. Read this informati on before using your Ericsson ADSL Wireless Router HN294d. Your ADSL Wireless Router HN294d is a highly sophisticated electronic ...

  • Garmin HN294DP/DI - page 87

    Important Infor mation EN/LZT 108 6377 R4 - Septembe r 2003 81 11.2 License Agreement This is a legal agreement, Agreement, between you, Licensee, the recipient of the enclosed Software on compact disc, diskette or any other media and any upgrades thereof, and Ericsson AB, the Vendor. By opening the sealed software package and/or using the software ...

  • Garmin HN294DP/DI - page 88

    Important Infor mation 82 EN/LZT 108 637 7 R4 - September 2003 and your exclusive remedy under this warranty (which is subject to you returning the Software to an certified reseller with a copy of your receipt) will be, at Vendor's option, to replace the disc(s) / diskette(s) or refund the purchase price for the Software and terminate this Agr ...

  • Garmin HN294DP/DI - page 89

    Important Infor mation EN/LZT 108 6377 R4 - Septembe r 2003 83 11.3 Regulatory Information 11.3.1 EU Directives The HN294d meet the following EU directives for the CE-mark:  73/23/EEC, Low Voltage Directive (LVD)  89/336/EEC, Electromagnetic Compatibility Directive (EMC)  1999/5/EC, Radio Equipment and Telecommunication Terminal Directive ...

  • Garmin HN294DP/DI - page 90

    Important Infor mation 84 EN/LZT 108 637 7 R4 - September 2003  CAN/CSA C22.2 No. 950-95  IEC 60950 2 nd Ed, 1991 + A1-A4 11.3.2.1 UL 1950 Statement When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use th ...

  • Garmin HN294DP/DI - page 91

    Important Infor mation EN/LZT 108 6377 R4 - Septembe r 2003 85  EN 300328-2 V1.2.1:2001 11.3.3.1 FCC Part 15 Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including i ...

  • Garmin HN294DP/DI - page 92

    Important Infor mation 86 EN/LZT 108 637 7 R4 - September 2003  FCC Part 68 11.3.4.1 FCC Part 68 Statement The Federal Communications Commission (FCC) has established Rules which permit this device to be directly connected to the telephone network. Standardized jacks are used for these connect ions. This equipment should not be used on party lin ...

  • Garmin HN294DP/DI - page 93

    Important Infor mation EN/LZT 108 6377 R4 - Septembe r 2003 87 Company: ASKEY International Corp. Address: 1751 Yeager Ave, La Verne, CA 91750, USA Tel: 909-596-5180. 11.3.5 Access Point Frequency Band 2412 MHz to 2472 MHz (subject to local regulations). 11.3.6 Caution Changes or modifications to this product not authorized by the manufacturer coul ...

  • Garmin HN294DP/DI - page 94

    Important Infor mation 88 EN/LZT 108 637 7 R4 - September 2003 Glossary - A - Access Point An Access Point (AP) is a hardware device or a computer's software that acts as a communication hub for users of a wireless device to connect to a wireless LAN (WLAN). The HN294dp has an integrated WLAN access point which complies to the 802.11b standard ...

  • Garmin HN294DP/DI - page 95

    Important Infor mation EN/LZT 108 6377 R4 - Septembe r 2003 89 - B - Bandwidth A measure of capacity of communications media. Greater bandwidth allows communication of more information in a given period of time. Bandwidth is generally described either in terms of analog signals in units of Hertz (Hz), which describes the maximum number of cycles pe ...

  • Garmin HN294DP/DI - page 96

    Important Infor mation 90 EN/LZT 108 637 7 R4 - September 2003 DNS Short for Domain Name System (or Service) , an Internet service that translates domain names into IP addresses. Because domain names are alphabetic, they're easier to remember. The Internet however, is really based on IP addresses. Every time you use a domain name, therefore, a ...

  • Garmin HN294DP/DI - page 97

    Important Infor mation EN/LZT 108 6377 R4 - Septembe r 2003 91 - E - Encapsulation A technology that enables one network to send its data via another network's connections. Encapsulation works by encapsulat ing a network protocol within packets carried by the second network. Encapsulation is also called tunneling. Ethernet A local-area network ...

  • Garmin HN294DP/DI - page 98

    Important Infor mation 92 EN/LZT 108 637 7 R4 - September 2003 G.lite A kind of asymmetric DSL technology, based on DMT modulation, that offers up to 1.5 megabits per second downstream bandwidth, 384 Kilobits per second upstream, does not usually require a splitter and is easier to install than other types of DSL. "G .lite" is a nickname ...

  • Garmin HN294DP/DI - page 99

    Important Infor mation EN/LZT 108 6377 R4 - Septembe r 2003 93 router, using Host Membership Reports, that it wants to receive messages addressed to a specific multicast gr oup. Intranet A network based on TCP/IP protocols (an internet) belonging to an organization, usually a corporation, accessible only by the organization's members, employee ...

  • Garmin HN294DP/DI - page 100

    Important Infor mation 94 EN/LZT 108 637 7 R4 - September 2003 - N - NAT Short for Network Address Translation , which is an Internet standard that translates a private IP address within one network to a public IP address, either a static or dynamic. NAT provides a type of firewall by hiding internal IP addresses and it also enables a company to us ...

  • Garmin HN294DP/DI - page 101

    Important Infor mation EN/LZT 108 6377 R4 - Septembe r 2003 95 broadband medium, such as a single DS L line, wireless device or cable modem. All the users over the Ethernet share a common connection, so the Ethernet principles supporting multiple users in a LAN combine with the principles of PPP, which apply to serial connections. PVC Short for Per ...

  • Garmin HN294DP/DI - page 102

    Important Infor mation 96 EN/LZT 108 637 7 R4 - September 2003 device will not be permitted to join the BSS unless it can provide the unique SSID. Because an SSID can be sniffed in plain text from a packet it does not supply any security to the network. An SSID is also referred to as a Network Name because essentially it is a name that identifies a ...

  • Garmin HN294DP/DI - page 103

    Important Infor mation EN/LZT 108 6377 R4 - Septembe r 2003 97 - U - UBR Sort for Unspecified Bit Rate . A type of ATM service that does not guarantee any throughput levels. This is used for applications, such a s file transfers, that can tolerate delays. UDP Short for User Datagram Protocol , which is a connectionless transport service that dispen ...

  • Garmin HN294DP/DI - page 104

    Important Infor mation 98 EN/LZT 108 637 7 R4 - September 2003 many virtual servers reside on the same computer, or if one virtual server starts hogging resources, Web pages will be delivered more slowly. VPI and VCI A VPI ( Virtual Path Identifier ) is an 8-bit field while VCI ( Virtual Channel Identifier ) is a 16-bit field in the ATM cell header ...

Manufacturer Garmin Category Network Router

Documents that we receive from a manufacturer of a Garmin HN294DP/DI can be divided into several groups. They are, among others:
- Garmin technical drawings
- HN294DP/DI manuals
- Garmin product data sheets
- information booklets
- or energy labels Garmin HN294DP/DI
All of them are important, but the most important information from the point of view of use of the device are in the user manual Garmin HN294DP/DI.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Garmin HN294DP/DI, service manual, brief instructions and user manuals Garmin HN294DP/DI. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Garmin HN294DP/DI.

Similar manuals

A complete manual for the device Garmin HN294DP/DI, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Garmin HN294DP/DI by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Garmin HN294DP/DI.

A complete Garmin manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Garmin HN294DP/DI - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Garmin HN294DP/DI, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Garmin HN294DP/DI, that we can find in the current document
3. Tips how to use the basic functions of the device Garmin HN294DP/DI - which should help us in our first steps of using Garmin HN294DP/DI
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Garmin HN294DP/DI
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Garmin HN294DP/DI in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Garmin HN294DP/DI?

Use the form below

If you did not solve your problem by using a manual Garmin HN294DP/DI, ask a question using the form below. If a user had a similar problem with Garmin HN294DP/DI it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)