Manual Pelco 06)

12 pages 2.82 mb
Download

Go to site of 12

Summary
  • Pelco 06) - page 1

    Hard Disk Drive Replacement Instructions C2616M (6/06) ...

  • Pelco 06) - page 2

    2 C2616M (6/06) Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Parts and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco 06) - page 3

    C2616M (6/06) 3 Introduction This manual provides instructions for replacing the primary master or secondary slave hard disk drive in a DX4000 Series DVR (digital video recorder). PARTS AND T OOLS NOTE: This replacement kit includes a Pelco-certified hard disk drive (160 GB or 250 GB). Using any other hard disk drive with the DX4000 voids the manu ...

  • Pelco 06) - page 4

    4 C2616M (6/06) Getting Started 1. Familiarize yourself with the instructions throughout this manual. 2. Check that you have all the necessary parts and tools. Refer to Parts and T ools on page 3. 3. If possible, back up all essential video before you install a new hard disk drive. If your unit contains two hard disk drives, back up all essential v ...

  • Pelco 06) - page 5

    C2616M (6/06) 5 Figure 2. ESD Protection A disposable ESD wrist strap (refer to Figure 3) is included with this kit. Attach the copper end of this wrist strap to any unpainted surface of an appliance that is grounded. An appliance is considered grounded if it can direct ESD to the earth usually through its power cable. An appliance that is plugged ...

  • Pelco 06) - page 6

    6 C2616M (6/06) Preparing the Unit to Install the Drive 1. T urn off power to the DX4000, and then remove the power cord from the unit. 2. Remove the top cover of the DVR (refer to Figure 4). a. Remove all nine screws from the DVR — three screws on each side and three on the top. Set aside the screws. Figure 4. Removing the Screws b. Slide the to ...

  • Pelco 06) - page 7

    C2616M (6/06) 7 Replacing the Hard Disk Install only blank hard disk drives received from the Pelco factory . Do not install a replacement hard disk drive that is already formatted. Hard disk drives that are already formatted can cause errors on the DX4000. 1. Locate the hard disk drive in the front of the DVR (refer to Figure 6). In a two-drive un ...

  • Pelco 06) - page 8

    8 C2616M (6/06) 3. V erify that the jumper on the replacement hard disk drive is set correctly as either Master or Slave. The Master hard disk drive requires a jumper; the Slave hard disk drive does not. Figure 7. Jumper Placement on Master Hard Disk Drive 4. Replace the hard disk drives. a. Set the jumper cable to the proper setting for the replac ...

  • Pelco 06) - page 9

    C2616M (6/06) 9 Reassembling the Unit 1. Replace the lid, and use the original screws to secure the lid in place. 2. Reconnect the power cord. 3. Restart the DX4000, and then follow the prompts to format the replacement hard disk drive. Formatting the New Hard Disk Drive The first time you start the DX4000 with a replacement hard disk drive, you w ...

  • Pelco 06) - page 10

    10 C2616M (6/06) After the hard disk drives are formatted, the Login screen appears with the Administrator user ID. Figure 10. Login Screen 3. Enter a password for the administrator , and then press the Enter button. The DX4000 is now ready again. Formatting a hard disk drive does not modify any settings for the DX4000; it merely prepares the hard ...

  • Pelco 06) - page 11

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series ...

  • Pelco 06) - page 12

    United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 ...

Manufacturer Pelco Category Computer Drive

Documents that we receive from a manufacturer of a Pelco 06) can be divided into several groups. They are, among others:
- Pelco technical drawings
- 06) manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco 06)
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco 06).

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco 06), service manual, brief instructions and user manuals Pelco 06). Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco 06).

Similar manuals

A complete manual for the device Pelco 06), how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco 06) by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco 06).

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco 06) - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco 06), FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco 06), that we can find in the current document
3. Tips how to use the basic functions of the device Pelco 06) - which should help us in our first steps of using Pelco 06)
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco 06)
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco 06) in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco 06)?

Use the form below

If you did not solve your problem by using a manual Pelco 06), ask a question using the form below. If a user had a similar problem with Pelco 06) it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)