Manual D-Link 2600

18 pages 1.02 mb
Download

Go to site of 18

Summary
  • D-Link 2600 - page 1

    DFE-2600 Series Web -based Management User’s Guide Rev. 02 (August, 1998) 6DFE2600..02 Printed In Taiwan RECYCLABLE ...

  • D-Link 2600 - page 2

    ii T ABLE OF C ONTENTS 0 W EB - BASED N ETWORK M ANAGEMENT .............................. 1 Introduction .................................................................................................................. 1 getting started ............................................................................................................... ...

  • D-Link 2600 - page 3

    1 1 0 W EB - BASED N ETWORK M ANAGEMENT Introduction The content of this user’s guide pertains to intelligent (management) Hub models only. An embedded web-based (hypertext) interface allows users to manage the switch from anywhere on the network through a standard browser such as Netscape Navigator/Communicator or Microsoft Internet E x plorer. ...

  • D-Link 2600 - page 4

    Dual-Speed Stackable Hub Web -based Management User’s Guide 2 The second and last step is to configure the IP interface, of the Hub, through console management. See the In -Band Setup Instructions on page 39 to do this. Management Your Hub has a hypertext interface, allowing you to do management through your browser. Your web -browser screen may ...

  • D-Link 2600 - page 5

    3 The Hub information is described as follows: ♦ System Description A description of the hub type. ♦ System OID The SNMP Object Identifier for this hub type. ♦ System Uptime The amount of time that the hub stack has been powered on. ♦ System Contact User-defined information for the physical location of the hub. ♦ System Name A user -assig ...

  • D-Link 2600 - page 6

    Dual-Speed Stackable Hub Web -based Management User’s Guide 4 The information is described as follows: ♦ IP Address The Internet address for the device. ♦ Subnet Mask The subnet mask determines the level of the subnet that the hub is on. ♦ Default Gateway The default router for the device. ♦ MAC Address The physical address for the device ...

  • D-Link 2600 - page 7

    5 ♦ Community This is the SNMP community name to authenticate the receiving of traps. ♦ Delete This will remove a trap receiver from the trap receiving table. Software Download The Software Download screen allows you to cause an immediate update of the hub’s parameters and/ or firmware. The fields are described as follows: ♦ Software Update ...

  • D-Link 2600 - page 8

    Dual-Speed Stackable Hub Web -based Management User’s Guide 6 ♦ Boot Server Address The IP address of the TFTP server where the configuration file is located. ♦ Boot Protocol Set to either bootp -tftp or tftp only . Applies only if the Software Update Control is enabled. ♦ Get IP From Bootp Server If enabled, the address will be obtained fr ...

  • D-Link 2600 - page 9

    7 Control The operations described in this section allow you to manage the Hub while it is operating. Group/ Port and Console Control Click Fault → Group/Port Control to show the Group/Port Configuration Control screen. Hub (group), port, and console configurations can be easily selected from this screen. Simply, click the particular component yo ...

  • D-Link 2600 - page 10

    Dual-Speed Stackable Hub Web -based Management User’s Guide 8 The information is described as follows: ♦ Current Serial Port Setting Displays the current session, either Console or Out-of -band . ♦ System Restart Serial Port Setting You can choose to select Console or Out-of -band management upon reboot. ♦ Baud Rate This is cps (characters ...

  • D-Link 2600 - page 11

    9 Group (Hub) Configuration Clicking Fault → Group/Port Control → [Hub ID] will show the current configuration information of the Hub. The information is described as follows: ♦ Serial Number This is a unique hardware serial number of the Hub. ♦ Description This is the product ID. ♦ Slot 1/ Slot 2 Type These indicate the type of module, i ...

  • D-Link 2600 - page 12

    Dual-Speed Stackable Hub Web -based Management User’s Guide 10 ♦ Isolated/ Reconnected Group This is an option to isolate or reconnect the Hub in the hub stack. Port Configuration Clicking Fault → Group/Port Control → [Port ID] will show the current configuration information of the port. The information is described as follows: ♦ Port Typ ...

  • D-Link 2600 - page 13

    11 ♦ Link Test Function State Indicates the whether the port link -test is enabled or disabled . If enabled, the port will check for link pulses, and will only transmit if there is a good link to another station. ♦ Administration State Indicates the port’s partition status, either enabled or disabled . ♦ Port Speed State Indicates how the p ...

  • D-Link 2600 - page 14

    Dual-Speed Stackable Hub Web -based Management User’s Guide 12 Performance Hub performance is measured with packet statistics and it’s utilization in the network. Statistics The Hub allows you to collect network statistics of individual ports, 10Mbps segments or 100Mbps segments, and any Hub in the stack. Statistics collected by the Hub are des ...

  • D-Link 2600 - page 15

    13 ♦ CRC AlignErrors ( Pkts) Counts otherwise valid frames that did not end on a byte (octet) boundary. ♦ UndersizePkts ( Pkts) Counts packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed. ♦ OversizePkts ( Pkts) Counts packets received that were longer than 1518 ...

  • D-Link 2600 - page 16

    Dual-Speed Stackable Hub Web -based Management User’s Guide 14 Utilization is calculated and plotted every 10 seconds. At any time, at most, a one hour utilization history can be shown by the graph. User List The User List display, displays the Ethernet (MAC) addresses of packets recently received by the hub stack. This information is displayed p ...

  • D-Link 2600 - page 17

    15 ♦ Time Shows the amount of time since the last packet was transmitted on the port. Intrusion The Hub’s intrusion security feature can be used to dedicate a port to a given piece of hardware. If a different device transmits to the port, the hub can be set to either partition the port, send a trap notification to the network manager, or both. ...

  • D-Link 2600 - page 18

    Dual-Speed Stackable Hub Web -based Management User’s Guide 16 ♦ Action The action to be taken in event of intrusion on the port: send trap , partition , send trap & partition , or no action . ♦ Auto Learn Can set auto -learning to enable or disable . ♦ Delete Click this to delete and disable a port/ intrusion entry. Back -Up Port A Bac ...

Manufacturer D-Link Category Webcam

Documents that we receive from a manufacturer of a D-Link 2600 can be divided into several groups. They are, among others:
- D-Link technical drawings
- 2600 manuals
- D-Link product data sheets
- information booklets
- or energy labels D-Link 2600
All of them are important, but the most important information from the point of view of use of the device are in the user manual D-Link 2600.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals D-Link 2600, service manual, brief instructions and user manuals D-Link 2600. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product D-Link 2600.

Similar manuals

A complete manual for the device D-Link 2600, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use D-Link 2600 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of D-Link 2600.

A complete D-Link manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual D-Link 2600 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the D-Link 2600, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the D-Link 2600, that we can find in the current document
3. Tips how to use the basic functions of the device D-Link 2600 - which should help us in our first steps of using D-Link 2600
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with D-Link 2600
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of D-Link 2600 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning D-Link 2600?

Use the form below

If you did not solve your problem by using a manual D-Link 2600, ask a question using the form below. If a user had a similar problem with D-Link 2600 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)