English dropdown-ico

Manual Gefen EXT-IP-2-RS2322

84 pages 1.58 mb
Download

Go to site of 84

Summary
  • Gefen EXT-IP-2-RS2322 - page 1

    Audio Embedder 3GSDI EXT-IP-2-RS2322 User Manual IP to RS-232 Converter *Pr eferred Release A1 ...

  • Gefen EXT-IP-2-RS2322 - page 2

    ii 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this product near water . 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer ’s instructions. 8. Do not install or place this product near any heat sources su ...

  • Gefen EXT-IP-2-RS2322 - page 3

    iii Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notied within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electric ...

  • Gefen EXT-IP-2-RS2322 - page 4

    iv T echnical S upport (818) 772-9100 (800) 545-6900 8:00 AM to 5:00 PM Monday - Friday , Pacic T ime Fa x (818) 772-9120 Email support@gefen.com We b http://www .gefen.com Mailing Addr ess Gefen, LLC c/o Customer Service 20600 Nordhoff St. Chatsworth, CA 9131 1 Pr oduct R egistr ation Register your product here: http://www .gefen.com/kvm/Regist ...

  • Gefen EXT-IP-2-RS2322 - page 5

    v v Operating Notes • When using the IP to 2 x RS-232 Converter for the rst time, it is recommended that the unit be congured using the Gefen Discovery T ool. The Gefen Discovery T ool is free software that is available from the Support > Downloads section of the Gefen Web site. IP to 2 x RS-232 Converter is a trademark of Gefen, LLC. © ...

  • Gefen EXT-IP-2-RS2322 - page 6

    vi Features and Packing List Features • Allows IP control of two RS-232-enabled devices • Supports T elnet and UDP protocols • Each of the RS-232 devices can be addressed independently • Congurable via Web server interface • Independently congurable RS-232 baud rate and line delay for each RS-232 port • Gefen Discovery T ool-compa ...

  • Gefen EXT-IP-2-RS2322 - page 7

    vii ...

  • Gefen EXT-IP-2-RS2322 - page 8

    viii Table of Contents 1 Get ting St arted Introduction............................................................................................................ 2 Installation ............................................................................................................. 4 Connection Instructions ................................... ...

  • Gefen EXT-IP-2-RS2322 - page 9

    ...

  • Gefen EXT-IP-2-RS2322 - page 10

    ...

  • Gefen EXT-IP-2-RS2322 - page 11

    IP to RS-232 Converter 1 Ge t ting St ar t ed Introduction............................................................................................................ 2 Installation ............................................................................................................. 4 Connection Instructions ................................ ...

  • Gefen EXT-IP-2-RS2322 - page 12

    page | 2 Introduction RS-232 1 Power IP Reset EXT -IP-2-RS2322 Gefen 5V DC IP control RS-232 2 IP to 2xRS-232 Converter RS-232 1 Power IP Reset EXT -IP-2-RS2322 Gefen 5V DC IP control RS-232 2 IP to 2xRS-232 Converter RS-232 1 Power IP Reset EXT -IP-2-RS2322 Gefen 5V DC IP control RS-232 2 IP to 2xRS-232 Converter 6 4 5 3 2 Getting S tart ed Gettin ...

  • Gefen EXT-IP-2-RS2322 - page 13

    page | 3 Introduction ID Name Description 1 IP Reset Resets the unit to its default IP settings. 2 RS-232 1 Connect an RS-232 cable from this port to an RS-232 device. See Installation (page 4 ) for more information. 3 Power This LED will glow bright blue when the unit is powered. 4 5V DC Connect the included 5V DC power supply to this power recept ...

  • Gefen EXT-IP-2-RS2322 - page 14

    page | 4 Installation Getting S tart ed Connection Instructions 1. Connect an Ethernet cable between the IP-based control device and the IP control port on the IP to 2 x RS-232 Converter . An Ethernet switch can also exist between the IP to 2 x RS-232 Converter and the IP-based control device (see Sample Wiring Diagram below). 2. Connect an RS-232 ...

  • Gefen EXT-IP-2-RS2322 - page 15

    ...

  • Gefen EXT-IP-2-RS2322 - page 16

    ...

  • Gefen EXT-IP-2-RS2322 - page 17

    page | 7 IP to RS-232 Converter 2 A dv anced Oper ation RS-232 and IP Conguration ................................................................................ 8 Conguration using the Gefen Discovery Tool .............................................. 8 Conguration using RS-232 ........................................................... ...

  • Gefen EXT-IP-2-RS2322 - page 18

    page | 8 RS-232 and IP Conguration Adv anced Oper ation Adv anced Oper ation Configuration using the Gefen Discovery Tool When using the IP to 2 x RS-232 Converter for the rst time, it is recommended that the unit be congured using the Gefen Discovery T ool. The Gefen Discovery T ool is free software that is available from the Support > ...

  • Gefen EXT-IP-2-RS2322 - page 19

    page | 9 Adv anced Oper ation Configuration using RS-232 T o congure the IP settings of the IP to 2 x RS-232 Converter using RS-232 commands, use the following procedure: 1. Connect a null-modem (“crossover”) cable from the RS-232 port on the computer to the IP to 2 x RS-232 Converter . The null-modem cable can be connected to either RS-232 ...

  • Gefen EXT-IP-2-RS2322 - page 20

    page | 10 RS-232 and IP Conguration Adv anced Oper ation Adv anced Oper ation 5. Set the gateway (router) IP address using the #set_gateway command. 6. Set the T elnet listening port using the #set_tcp_term_port command. 7. Set the HTTP listening port using the #set_http_port command. 8. Set the UDP remote IP address using the #set_udp_rip comma ...

  • Gefen EXT-IP-2-RS2322 - page 21

    page | 1 1 Adv anced Oper ation Command Description #help Displays a list of all available commands #set_add_delim Enables or disables option to add delimiter to data #set_device_descr Sets the device description #set_end_del Sets the end frame delimiter #set_gateway Sets the gateway (router) IP address #set_http_port Sets the HTTP listening port o ...

  • Gefen EXT-IP-2-RS2322 - page 22

    page | 12 Adv anced Oper ation Adv anced Oper ation Commands Command Description #show_serial_params Displays the settings of the specied RS-232 port #show_telnet_pass Displays the current TCP terminal password #show_ver_data Displays the rmware and hardware version of the IP to RS-232 Converter #system_wide_reset Restarts the IP to 2 x RS-23 ...

  • Gefen EXT-IP-2-RS2322 - page 23

    page | 13 Adv anced Oper ation Commands #help Displays help on a specic command. If no command is specied ( param1 ), then a list of all available commands will be displayed. Set param1 to “full” to display a list of all commands. S yntax #help P ar amet ers param1 Command (optional) Example #help #set_add_delim Cmd #set_add_delim: Set Ad ...

  • Gefen EXT-IP-2-RS2322 - page 24

    page | 14 Commands Adv anced Oper ation Adv anced Oper ation #help #show_ipcong #set_ipadd #set_netmask #set_gateway #set_http_port #set_tcp_term_port #set_udp_port #show_ver_data #show_telnet_pass #set_telnet_pass #use_tcp_term_pass #set_udp_rip #set_udp_rport #use_udp_access #use_udp_echo #use_tcp_access #set_serial_params #show_serial_params ...

  • Gefen EXT-IP-2-RS2322 - page 25

    page | 15 Commands Adv anced Oper ation #set_add_delim Enables or disables the option to include a delimiter as part of the data sent to the control system. S yntax #set_add_delim param1 param2 P ar amet ers param1 V alue [1 ... 2] param2 State [0 ... 1] V alue Description 0 Off 1 On Example #set_add_delim 1 Add delimiter mode to ON R elated C omma ...

  • Gefen EXT-IP-2-RS2322 - page 26

    page | 16 Commands Adv anced Oper ation Adv anced Oper ation #set_device_descr Sets the device description. The device description cannot exceed 30 characters in length S yntax #set_device_descr param1 P ar amet ers param1 Description [30 chars max.] Example #set_device_descr LivingRoom_Bridge2 Device Description changed to: LivingRoom_Bridge2 R el ...

  • Gefen EXT-IP-2-RS2322 - page 27

    page | 17 Commands Adv anced Oper ation #set_end_del Sets the end-delimiter mode and value for the specied serial port. The End Delimiter value must be specied in hexadecimal. Before executing this command, the Start Delimiter must be set, using the #set_start_del command. S yntax #set_end_del param1 param2 param3 P ar amet ers param1 Serial ...

  • Gefen EXT-IP-2-RS2322 - page 28

    page | 18 Commands #set_gateway Sets the gateway address. The gateway must be typed using dot-decimal notation. The matrix must be rebooted after executing this command. The default gateway is 192.168.1.1 . S yntax #sgateway param1 P ar amet ers param1 Gateway Example #set_gateway 10.5.64.1 New IP Gateway set to: 10.5.64.1 R elated C ommands #set_a ...

  • Gefen EXT-IP-2-RS2322 - page 29

    page | 19 Commands #set_http_port Species the Web server listening port. The unit must be rebooted after executing this command. The default port setting is 80 . S yntax #set_http_port param1 P ar amet ers param1 Port [1 ... 1024] Example #set_http_port 82 New HTTP port set to: 82 R elated C ommands #set_gateway #set_ipadd #set_netmask #show_ipc ...

  • Gefen EXT-IP-2-RS2322 - page 30

    page | 20 Commands #set_ipadd Species the IP address of the IP to 2 x RS-232 Converter . The IP address must be specied using dot-decimal notation. The unit must be rebooted after executing this command. The default IP address is 192.168.1.72 . S yntax #set_ipadd param1 P ar amet ers param1 IP address Example #set_ipadd 10.5.64.187 New IP set ...

  • Gefen EXT-IP-2-RS2322 - page 31

    page | 21 Commands #set_netmask Sets the subnet mask. The subnet mask must be entered using dot-decimal notation. The unit must be rebooted after executing this command. The default net mask is 255.255.255.0 . S yntax #snetmask param1 P ar amet ers param1 Net mask Example #snetmask 255.255.0.0 New IP Mask set to: 255.255.0.0 R elated C ommands #set ...

  • Gefen EXT-IP-2-RS2322 - page 32

    page | 22 Commands #set_send_byte_cnt Sets the send-byte count value for bridging mode. S yntax #set_send_byte_cnt param1 P ar amet ers param1 Serial port [1 ... 2] param2 Byte count [0 ... 255] Example #set_send_byte_cnt 1 100 UART 1 bridging send byte count limit is set to 100 bytes R elated C ommands #set_add_delim #set_end_del #set_serial_mode ...

  • Gefen EXT-IP-2-RS2322 - page 33

    page | 23 Commands #set_send_time_out Sets the time-out value for sending data collected from a device to the control system in Bridging Mode when a Start Delimiter and End Delimiter have been set. If no data has been collected for the specied time, the data is sent without waiting for the End Delimiter . S yntax #set_send_time_out param1 P ar a ...

  • Gefen EXT-IP-2-RS2322 - page 34

    page | 24 Commands #set_serial_descr Assigns a descriptor to the specied serial port. The serial port description cannot exceed 20 characters in length. The default description is None . S yntax #set_serial_descr param1 param2 P ar amet ers param1 Port [1 ... 2] param2 Description [20 chars max.] Example #set_serial_descr 1 DVD_Ctrl Serial port ...

  • Gefen EXT-IP-2-RS2322 - page 35

    page | 25 Commands #set_serial_mode Sets the mode of the specied serial port. The default mode for all serial ports (1 - 2) is TCP Bridge mode. S yntax #set_serial_mode param1 param2 P ar amet ers param1 Port [1 ... 2] param2 State [1 ... 3] Mode Description 1 TCP bridge 2 UDP bridge 3 T erminal mode Example #set_serial_mode 1 2 Serial port 1 wo ...

  • Gefen EXT-IP-2-RS2322 - page 36

    page | 26 Commands Adv anced Oper ation Adv anced Oper ation #set_serial_params Assigns the settings to the specied serial port. S yntax #set_serial_params param1 param2 param3 param4 param5 param6 P ar amet ers param1 Port [1 ... 3] param2 Word length [5 ... 8] param3 Stop bits [1 ... 2] param4 Parity Parity Description n None e Even o Odd m Ma ...

  • Gefen EXT-IP-2-RS2322 - page 37

    page | 27 Commands Adv anced Oper ation Example #set_serial_params 1 8 1 N 19200 1000 Serial port 1 parameters: Word length = 8 bits Stop bits = 1 bit Parity = None Baud Rate = 19200 Bps Line Delay = 1000 ms R elated C ommands #show_serial_params ...

  • Gefen EXT-IP-2-RS2322 - page 38

    page | 28 Commands Adv anced Oper ation Adv anced Oper ation #set_start_del Sets the Start Delimiter mode and value for the specied serial port. The Start Delimiter must always be specied before the End Delimiter . S yntax #set_start_del param1 param2 param3 P ar amet ers param1 Serial port [1 ... 2] param2 State [0 ... 1] Mode Description 1 ...

  • Gefen EXT-IP-2-RS2322 - page 39

    page | 29 Commands Adv anced Oper ation #set_tcp_br_port Sets the TCP bridge listening port for the specied serial port. The default port settings for RS-232 1 and RS-232 2 ports are 49200 and 49201, respectively . S yntax #set_tcp_br_port param1 param2 P ar amet ers param1 Serial port [1 ... 2] param2 TCP port [1 ... 65535] Example #set_tcp_br_ ...

  • Gefen EXT-IP-2-RS2322 - page 40

    page | 30 Commands Adv anced Oper ation Adv anced Oper ation #set_tcp_term_port Sets the TCP terminal listening port. The default port settings is 23 . S yntax #set_tcp_term_port param1 P ar amet ers param1 TCP port [1 ... 65535] Example #set_tcp_term_port 23 New TCP Terminal port set to: 23 R elated C ommands #set_tcp_br_port #set_udp_br_port ...

  • Gefen EXT-IP-2-RS2322 - page 41

    page | 31 Commands Adv anced Oper ation #set_telnet_pass Sets the TCP T erminal password. The password cannot exceed 20 characters in length. param3 is used to verify the new password. The default password is Admin . S yntax #set_telnet_pass param1 param2 param3 P ar amet ers param1 Old password [20 chars max.] param2 New password [20 chars max.] p ...

  • Gefen EXT-IP-2-RS2322 - page 42

    page | 32 Commands Adv anced Oper ation Adv anced Oper ation #set_udp_br_port Sets the UDP bridge listening port. The default UDP bridge port settings for RS-232 1 and RS-232 2 ports are 50200 and 50201, respectively . S yntax #set_udp_br_port param1 param2 P ar amet ers param1 Serial port [1 ... 2] param2 Port [1 ... 65535] Example #set_udp_br_por ...

  • Gefen EXT-IP-2-RS2322 - page 43

    page | 33 Commands Adv anced Oper ation #set_udp_echo_br Enables or disables UDP bridge echo. S yntax #set_udp_echo_br param1 param2 P ar amet ers param1 Serial port [1 ... 2] param2 State [0 ... 1] State Description 0 Disabled 1 Enabled Example #set_udp_echo_br 1 1 The echo of UDP Bridge port 1 is enabled R elated C ommands #set_udp_br_port #set_u ...

  • Gefen EXT-IP-2-RS2322 - page 44

    page | 34 Commands Adv anced Oper ation Adv anced Oper ation #set_udp_port Sets the UDP server listening port S yntax #set_udp_port param1 P ar amet ers param1 Serial port [1 ... 65535] Example #set_udp_port 50007 New UDP server port set to: 50007 R elated C ommands #set_udp_br_port #set_udp_remote_br #set_udp_echo_br #set_udp_rip #set_udp_rport ...

  • Gefen EXT-IP-2-RS2322 - page 45

    page | 35 Commands Adv anced Oper ation #set_udp_remote_br Assigns the UDP Bridge settings for the specied serial port. param2 must be entered in dot-decimal notation. S yntax #set_udp_remote_br param1 param2 param3 P ar amet ers param1 Serial port [1 ... 2] param2 Address param3 Remote port [1 ... 65535] Example #set_udp_remote_br 1 192.168.1.7 ...

  • Gefen EXT-IP-2-RS2322 - page 46

    page | 36 Commands Adv anced Oper ation Adv anced Oper ation #set_udp_rip Sets the remote UDP IP address. The IP address must be entered using dot-decimal notation. Each digit can range between 0 and 255. S yntax #set_udp_rip param1 P ar amet ers param1 IP address Example #set_udp_rip 192.168.1.205 New Remote UDP IP set to: 192.168.1.205 R elated C ...

  • Gefen EXT-IP-2-RS2322 - page 47

    page | 37 Commands Adv anced Oper ation #set_udp_rport Sets the remote UDP listening port. The default port settings is 50008 . S yntax #set_udp_rport param1 P ar amet ers param1 Port [1 ... 65535] Example #set_udp_rport 50006 New UDP Remote port set to: 50006 R elated C ommands #set_udp_br_port #set_udp_echo_br #set_udp_remote_br #set_udp_rip ...

  • Gefen EXT-IP-2-RS2322 - page 48

    page | 38 Commands Adv anced Oper ation Adv anced Oper ation #show_del_prms Displays the current delimiter parameters for the specied serial port. S yntax #show_del_prms param1 P ar amet ers param1 Port [1 ... 2] Example #show_del_prms 1 Delimiter Param’s in bridge mode, UART 1 Line Delay = 1000ms Time To Force Send = 30ms Count Byte To Force ...

  • Gefen EXT-IP-2-RS2322 - page 49

    page | 39 Commands Adv anced Oper ation #show_device_descr Displays the device description. S yntax #show_device_descr P ar amet ers None Example #show_device_descr Device Description: IP_BRIDGE R elated C ommands #set_device_descr ...

  • Gefen EXT-IP-2-RS2322 - page 50

    page | 40 Commands Adv anced Oper ation Adv anced Oper ation #show_ipcong Displays the current TCP/IP and UDP settings. S yntax #show_ipcong P ar amet ers None Example #show_ipcong --------- IP to 2 x RS-232 Converter settings --------- MAC addr = 00:1C:91:01:0F:FF IP addr = 10.5.64.254 Net Mask = 255.255.255.0 Gateway = 192.168.1.254 Web ...

  • Gefen EXT-IP-2-RS2322 - page 51

    page | 41 Commands Adv anced Oper ation #show_me Enables or disables the ashing of the LED on the device. When enabled, the LED indicator will ash red and blue. The default setting is disabled. S yntax #show_me param1 P ar amet ers param1 State State Description 0 Disabled 1 Enabled Example #show_me 1 Show me is Enabled R elated C ommands #us ...

  • Gefen EXT-IP-2-RS2322 - page 52

    page | 42 Commands Adv anced Oper ation Adv anced Oper ation #show_serial_descr Displays the description of the specied serial port. S yntax #show_serial_descr param1 P ar amet ers param1 Port [1 ... 2] Example #show_serial_descr 1 Serial port 1 Description: DVD_Ctrl R elated C ommands #set_serial_descr ...

  • Gefen EXT-IP-2-RS2322 - page 53

    page | 43 Commands Adv anced Oper ation #show_serial_mode Displays the mode of the specied serial port. S yntax #show_serial_mode param1 P ar amet ers param1 Port [1 ... 2] Example #show_serial_mode 1 Serial port 1 working mode is: TCP Bridge Mode R elated C ommands #set_serial_mode ...

  • Gefen EXT-IP-2-RS2322 - page 54

    page | 44 Commands Adv anced Oper ation Adv anced Oper ation #show_serial_params Displays the current settings of the specied serial port. S yntax #show_serial_params param1 P ar amet ers param1 Port [1 ... 2] Example #show_serial_params 1 Serial port 1 parameters: Word length = 8 bits Stop bits = 1 bit Parity = None Baud Rate = 19200 Bps Line D ...

  • Gefen EXT-IP-2-RS2322 - page 55

    page | 45 Commands Adv anced Oper ation #show_telnet_pass Displays the current TCP terminal password. S yntax #show_telnet_pass P ar amet ers None Example #show_telnet_pass TCP Terminal password: b055man R elated C ommands #set_telnet_pass ...

  • Gefen EXT-IP-2-RS2322 - page 56

    page | 46 Commands Adv anced Oper ation Adv anced Oper ation #show_ver_data Displays the current software and hardware version. S yntax #show_ver_data P ar amet ers None Example #show_ver_data Firmware version 1.48 Release date: May 12 2014 Release time: 14:09:37 ...

  • Gefen EXT-IP-2-RS2322 - page 57

    page | 47 Commands Adv anced Oper ation #system_wide_reset Restarts the IP to 2 x RS-232 Converter according to the supplied parameter . S yntax #system_wide_reset param1 P ar amet ers param1 V alue [0 ... 3] V alue Description 0 Reboot only 1 Reset IP settings 2 Reset serial port settings 3 Reset all and reboot Example #system_wide_reset 3 System ...

  • Gefen EXT-IP-2-RS2322 - page 58

    page | 48 Commands Adv anced Oper ation Adv anced Oper ation #use_discovery Enables or disables discovery access mode. If this mode is disabled, then the IP to 2 x RS-232 Converter will not be discoverable when using the Gefen Discovery T ool. The default setting is enabled . S yntax #use_discovery param1 P ar amet ers param1 State State Descriptio ...

  • Gefen EXT-IP-2-RS2322 - page 59

    page | 49 Commands Adv anced Oper ation #use_tcp_access Enables or disables TCP access mode. This mode must be enabled before using RS-232 command to congure the IP to 2 x RS-232 Converter . S yntax #use_tcp_access param1 P ar amet ers param1 V alue [0 ... 1] V alue Description 0 Disable TCP access 1 Enable TCP access Example #use_tcp_access 1 T ...

  • Gefen EXT-IP-2-RS2322 - page 60

    page | 50 Commands Adv anced Oper ation Adv anced Oper ation #use_tcp_term_pass Enables or disables the use of the password during terminal sessions. S yntax #use_tcp_term_pass param1 P ar amet ers param1 V alue [0 ... 1] V alue Description 0 Do not use password 1 Require password Example #use_tcp_term_pass 1 TCP Terminal password at login is set t ...

  • Gefen EXT-IP-2-RS2322 - page 61

    page | 51 Commands Adv anced Oper ation #use_udp_access Enables or disables UDP access. S yntax #use_udp_access param1 P ar amet ers param1 V alue [0 ... 1] V alue Description 0 Disable UDP access 1 Enable UDP access Example #use_udp_access 1 UDP Access is set to Enabled R elated C ommands #set_udp_br_port #set_udp_echo_br #set_udp_remote_br #set_u ...

  • Gefen EXT-IP-2-RS2322 - page 62

    page | 52 #use_udp_echo Enables or disables UDP echo. S yntax #use_udp_echo param1 P ar amet ers param1 V alue [0 ... 1] V alue Description 0 Disable UDP echo 1 Enable UDP echo Example #use_udp_echo 1 UDP echo is set to Enabled R elated C ommands #set_udp_echo_br Commands Adv anced Oper ation Adv anced Oper ation ...

  • Gefen EXT-IP-2-RS2322 - page 63

    page | 53 Adv anced Oper ation Web Interface Using the built-in Web Interface Access the built-in Web interface by entering the IP address of the IP to 2 x RS-232 Converter that was specied in step 3 under Conguration using RS-232 (page 9) . The built-in Web interface is divided into three pages: RS-232, Network, and System. Each main page is ...

  • Gefen EXT-IP-2-RS2322 - page 64

    page | 54 Web Interface RS-232 Select RS-232 Port Select the RS-232 port from the drop-down list. Options: 1 , 2 Description Enter a description for the device that is connected to the selected RS-232 port. RS-232 Mode Select the desired mode from the drop-down list. Options: TCP Bridge , UDP Bridge , T erminal Adv anced Oper ation Adv anced Oper a ...

  • Gefen EXT-IP-2-RS2322 - page 65

    page | 55 Web Interface Baud Rate Select the baud rate used by the RS-232 device from this drop-down list. Options : 1 10, 300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 28800 Data Bits Select the number of data bits in each character from this drop-down list. For most applications, 8 data bits should be selected. 9 data bits are rarely used. Opti ...

  • Gefen EXT-IP-2-RS2322 - page 66

    page | 56 Web Interface Line Delay (ms) Enter the line delay in this eld. Range : 0 ... 10000 Force Send (ms) If no data is received from the controlled device within the specied time interval, send the collected data to the control system. Range : 0 ... 30 Force Send (bytes) If the specied number of bytes is received from the controlled d ...

  • Gefen EXT-IP-2-RS2322 - page 67

    page | 57 Web Interface Add Delimiters to data sent Include the delimiter characters in the data sent to the control system. Check the Add box to enable this feature. Options : Enable (checked), Disable (unchecked) Use Start Delimiter Includes the Start Frame Delimiter , used at the end of the preamble of an Ethernet frame. Options : Enable (checke ...

  • Gefen EXT-IP-2-RS2322 - page 68

    page | 58 Web Interface End Delimiter V alue This value can be up to three ASCII characters (3 bytes), in length. The value must be entered in hexadecimal Range : 00 ... FF (“wildcard” characters, such as **, are acceptable) TCP Port Enter the TCP port in this eld. Range : 0 ... 65535 UDP Local Port Enter the UPD local port in this eld. R ...

  • Gefen EXT-IP-2-RS2322 - page 69

    page | 59 Web Interface Destination IP Enter the destination (where the data will be sent) IP address in this eld. Range (per byte) : 0 ... 255 Destination Port Enter the destination port in this eld. Range : 1024 ... 65535 UDP Echo Useful in troubleshooting and measuring response times and end-to-end connectivity . Options : Enable (checked) ...

  • Gefen EXT-IP-2-RS2322 - page 70

    page | 60 Web Interface Network tab MAC Address The MAC address of the IP to RS-232 Converter . The MAC address cannot be changed. Mode Select the network mode from the drop-down list. Options : Static , DHCP IP Address Enter the IP address of the IP to 2 x RS-232 Converter . Range (per byte) : 0 ... 255 Subnet Enter the subnet mask of the IP to 2 ...

  • Gefen EXT-IP-2-RS2322 - page 71

    page | 61 Web Interface Gateway The gateway (router) IP address to with the IP to 2 x RS-232 Converter is connected. Range (per byte) : 0 ... 255 HTTP Port Select the network mode from the drop-down list. Range (per byte) : 1 ... 1024 Adv anced Oper ation ...

  • Gefen EXT-IP-2-RS2322 - page 72

    page | 62 Web Interface Enable TCP Access Enables or disables TCP access. Options : Enable (checked) , Disable (unckecked) Require Password on Connect Forces password prompt for T elnet sessions. Options : Enable (checked) , Disable (unckecked) User Name Displays the user name for TCP sessions. The user name cannot be changed. Old Password T ype th ...

  • Gefen EXT-IP-2-RS2322 - page 73

    page | 63 Web Interface New Password T ype the new password in this eld. The password is automatically masked when entered. The password is case-sensitive. Maximum length: 8 characters Conrm Password Re-type the new password in this eld. The password must match the same password that was entered in the New Password eld. Maximum length: ...

  • Gefen EXT-IP-2-RS2322 - page 74

    page | 64 Web Interface Enable UDP Access Enables or disables UDP access. Options : Enable (checked) , Disable (unckecked) UDP Port Sets the UDP port. Range : 1 ... 1024 Enable UDP Echo Enables or disables UDP echo. Options : Enable (checked) , Disable (unckecked) Adv anced Oper ation Adv anced Oper ation ...

  • Gefen EXT-IP-2-RS2322 - page 75

    page | 65 Web Interface Destination UDP IP Address Enter the remote UDP IP address in this eld. Range (per byte) : 0 ... 255 Destination UDP Port T ype the remote UDP port in this eld. Range : 1 ... 1024 Enable Discovery Enables or disables discovery mode. This feature must be enabled in order for the Gefen Discovery T ool to detect the unit ...

  • Gefen EXT-IP-2-RS2322 - page 76

    page | 66 Web Interface Adv anced Oper ation Adv anced Oper ation System tab Download (Download Current Conguration) Saves the current conguration of the IP to 2 x RS-232 Converter to a le. Browse... (Restore Conguration) Selects the conguration le to load. See the Download button, above. Restore Click this button to upload the se ...

  • Gefen EXT-IP-2-RS2322 - page 77

    page | 67 Web Interface Adv anced Oper ation Browse... (Firmware Update) Click this button to select the rmware le to be uploaded. Update Click this button to upload the selected rmware le. See the Browse... button, above. Factory Reset Use these check boxes to select the type of factory-reset to perform. Placing a check mark in the des ...

  • Gefen EXT-IP-2-RS2322 - page 78

    ...

  • Gefen EXT-IP-2-RS2322 - page 79

    IP to RS-232 Converter 3 Appendix Default Settings ................................................................................................... 70 RS-232 ........................................................................................................ 70 Network ......................................................................... ...

  • Gefen EXT-IP-2-RS2322 - page 80

    page | 70 Default Settings Appendix Appendix The following table lists the default setting of the IP to 2 x RS-232 Converter , as displayed under the built-in Web interface. RS-232 RS-232 Settings Select RS-232 Port • 1 Description • None RS-232 Mode • TCP Bridge Baud Rate • 19200 Data Bits • 8 Parity • None Stop Bits • 1 Bridging Set ...

  • Gefen EXT-IP-2-RS2322 - page 81

    page | 71 Appendix Network IP Settings MAC Address • Device-dependent (cannot be changed) Mode • Static IP Address • 192.168.1.72 Subnet • 255.255.255.0 Gateway • 192.168.1.254 HTTP Port • 80 TCP / T elnet Settings Enable TCP Access • Disabled Require Password on Connect • Disabled User Name • Admin (cannot be changed) Old Passwor ...

  • Gefen EXT-IP-2-RS2322 - page 82

    page | 72 Appendix Connectors, Indicators, and Controls RS-232 • 2 x DB-9, male IP control • 1 x RJ-45 Power • 1 x 5V DC, locking Power indicator • 1 x LED, blue IP Reset button • 1 x T act-type, recessed Operational Power • 5V DC Power consumption • 1W (max.) Physical Dimensions (W x H x D) • 4.3” x 1” x 3.4” (1 10mm x 26mm x ...

  • Gefen EXT-IP-2-RS2322 - page 83

    ...

  • Gefen EXT-IP-2-RS2322 - page 84

    20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.com Stretch it. Switch it. Split it. Gefen’s got it. ® 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.com *Pr eferred ...

Manufacturer Gefen Category Marine Battery

Documents that we receive from a manufacturer of a Gefen EXT-IP-2-RS2322 can be divided into several groups. They are, among others:
- Gefen technical drawings
- EXT-IP-2-RS2322 manuals
- Gefen product data sheets
- information booklets
- or energy labels Gefen EXT-IP-2-RS2322
All of them are important, but the most important information from the point of view of use of the device are in the user manual Gefen EXT-IP-2-RS2322.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Gefen EXT-IP-2-RS2322, service manual, brief instructions and user manuals Gefen EXT-IP-2-RS2322. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Gefen EXT-IP-2-RS2322.

Similar manuals

A complete manual for the device Gefen EXT-IP-2-RS2322, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Gefen EXT-IP-2-RS2322 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Gefen EXT-IP-2-RS2322.

A complete Gefen manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Gefen EXT-IP-2-RS2322 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Gefen EXT-IP-2-RS2322, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Gefen EXT-IP-2-RS2322, that we can find in the current document
3. Tips how to use the basic functions of the device Gefen EXT-IP-2-RS2322 - which should help us in our first steps of using Gefen EXT-IP-2-RS2322
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Gefen EXT-IP-2-RS2322
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Gefen EXT-IP-2-RS2322 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Gefen EXT-IP-2-RS2322?

Use the form below

If you did not solve your problem by using a manual Gefen EXT-IP-2-RS2322, ask a question using the form below. If a user had a similar problem with Gefen EXT-IP-2-RS2322 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)