Manual Roland VC-300HD

48 pages 4.17 mb
Download

Go to site of 48

Summary
  • Roland VC-300HD - page 1

    Copyright © 2007 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Owner’s Manual 201b This manual describes the VC-300HD and the VC-200HD. When reading this manual, please note the following. • VC-300HD-specific features are marked with in th ...

  • Roland VC-300HD - page 2

    2 IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION : RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilater ...

  • Roland VC-300HD - page 3

    3 Table of Contents USING THE UNIT SAFELY .......................................4 IMPORTANT NOTES ................................................6 Features ....................................................................7 Checking the Included Items ..................................8 Basic Operation ................................. 9 Panel ...

  • Roland VC-300HD - page 4

    4 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. .......................................................................................................... 001-50 • Connect mains plug of this model to a mains socket outlet with a protective earthing connection. ........... ...

  • Roland VC-300HD - page 5

    USING THE UNIT SAFELY 5 012a • Immediately turn the power off, remove the power cord from the outlet, and request servicing by your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page when: • The power-supply cord, or the plug has been damaged; or • If smoke or unusual odor ...

  • Roland VC-300HD - page 6

    6 IMPORTANT NOTES 291b In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 2 and 4–5, please read and observe the following: 301 • Do not connect this unit to same electrical outlet that is being used by an electrical appliance that is controlled by an inverter (such as a refrigerat ...

  • Roland VC-300HD - page 7

    7 Features HDV/DV Conversion Feature This converts analog component, DVI-I, or SDI (HD/SD) signals to HDV or DV in real time. It can also go the other way and convert HDV or DV streams to analog component, DVI, or SDI (HD/SD) signals. * Only the VC-300HD supports SDI signals. High-performance Scaler The unit has a built-in scaler that can convert i ...

  • Roland VC-300HD - page 8

    8 Checking the Included Items The VC-300HD/VC-200HD is packaged with the following items. Please check that all of the items are included. * If you find that any item is missing, contact the nearest authorized EDIROL/Roland distributor in your country. VC-300HD / VC-200HD Power Cord * Use only the attached power-supply cord. Rubber Feet (4) * The r ...

  • Roland VC-300HD - page 9

    9 Basic Operation ...

  • Roland VC-300HD - page 10

    10 Panel Descriptions 1 i.LINK Connector (Front Panel) This connector handles the input/output of HDV/DV signals and allows for connection of HDV/DV video equipment. * Please do not use this together with the i.LINK connector (p. 13) on the rear panel of the unit. If they are used together, the connected video equipment may not operate properly. 2 ...

  • Roland VC-300HD - page 11

    11 Panel Descriptions 6 Display Shows the Status screens (four types) indicating the status of the unit. Pressing the PAGE button cycles you through the Status screens. The Menu screen is displayed by pressing MENU button. While the Menu screen is displayed, the MENU button is lit. 7 PAGE Button Pressed to select what is shown in the display, such ...

  • Roland VC-300HD - page 12

    12 Panel Descriptions 1 AC Inlet Accepts connection of the supplied power cord. 2 AUDIO OUTPUT Connectors CH1 and CH2 Connectors (XLR Type/Balanced Type) CH3 and CH4 Connectors (RCA Phono Type, Unbalanced Input) These connectors provide output of analog audio. Here is where you connect equipment such as monitoring speakers or a television, or a vid ...

  • Roland VC-300HD - page 13

    13 Panel Descriptions 10 TERMINATOR Switch Switch this on when you don’t want to loop-through the synchronizing signal from the REF OUTPUT connector. 11 REF OUTPUT Connector This is the loop through output connector for external synchronizing signals input via the REF INPUT connector. It is connected to the external synchronizing signal input con ...

  • Roland VC-300HD - page 14

    14 Connecting Connect the VC-200HD or VC-300HD in the way that is appropriate for the intended purpose. This section describes how the various connections need to be made, according to purpose. Connection Overview and Support Pages * The combinations indicated with in the chart are input/output that can be converted. * The input/output combinations ...

  • Roland VC-300HD - page 15

    15 Connecting HD component video can be converted to HDV, and the HD video can be recorded onto HDV tape. When recording HD component output from an HD video switcher, inexpensive HDV tape can be used. Connection and Configuration 1 Connect the HD video device to the COMPONENT INPUT connector using a BNC cable. * Make sure to connect the BNC cable ...

  • Roland VC-300HD - page 16

    16 Connecting 6 Select the output format. 6-1. Press the OUTPUT button until "300: Video Out Format" is shown in the display. 6-2. Use the VALUE/ENTER knob to select "1080/59.94i," "1080/50i," "720/59.94p," or "720/50p." 6-3. Press the VALUE/ENTER knob to confirm the selection. The video signal is o ...

  • Roland VC-300HD - page 17

    17 Connecting Since the VC-300HD/VC-200HD offers HD-SDI input, the HD-SDI or SDI from an HD video device can be converted to HDV. The output from the HD video switcher can be recorded in HDV, or the video from an HD video deck can be converted to HDV. Connection and Configuration 1 Connect the HD video device to the HD-SDI IN connector using a BNC ...

  • Roland VC-300HD - page 18

    18 Connecting 6 Select the output format. 6-1. Press the OUTPUT button until "300: Video Out Format" is shown in the display. 6-2. Use the VALUE/ENTER knob to select "1080/59.94i," "1080/50i," "720/59.94p," or "720/50p." 6-3. Press the VALUE/ENTER knob to confirm the selection. The video signal is o ...

  • Roland VC-300HD - page 19

    19 Connecting DVI or VGA output from a computer can be converted to HDV, and the high resolution images can be recorded to a video. Because the computer screen can be recorded in HD, small text and graphics do maintain clarity. * To input VGA output to the VC-300HD/VC-200HD, please use an RGB-DVI conversion connector and cable to convert to the DVI ...

  • Roland VC-300HD - page 20

    20 Connecting 6 Select the output format. 6-1. Press the OUTPUT button until "300: Video Out Format" is shown in the display. 6-2. Use the VALUE/ENTER knob to select "1080/59.94i," "1080/50i," "720/59.94p," or "720/50p." 6-3. Press the VALUE/ENTER knob to confirm the selection. The video signal is o ...

  • Roland VC-300HD - page 21

    21 Connecting When video recorded in HDV is converted to HD component, it can be used as HD analog video on an HD video device or in an HD linear editing environment. Connection and Configuration 1 Connect the HDV device to the i.LINK connector using a i.LINK (IEEE1394) cable. 2 Connect the HD video device to the COMPONENT OUTPUT connector using a ...

  • Roland VC-300HD - page 22

    22 Connecting 6 Select the output format. 6-1. Press the OUTPUT button until "300: Video Out Format" is shown in the display. 6-2. Use the VALUE/ENTER knob to select "1080/59.94i," "1080/50i," "720/59.94p," or "720/50p." 6-3. Press the VALUE/ENTER knob to confirm the selection. The video signal is o ...

  • Roland VC-300HD - page 23

    23 Connecting Video recorded in HDV can be converted to HD-SDI and copied to an HD video device, such as HDCAM or DVCPRO HD, or transmitted over a long distance. Connection and Configuration 1 Connect the HDV device to the i.LINK connector using a i.LINK (IEEE1394) cable. 2 Connect the HD video device to the COMPONENT OUTPUT connector using a BNC c ...

  • Roland VC-300HD - page 24

    24 Connecting 5 Select the output format. 5-1. Press the OUTPUT button until "300: Video Out Format" is shown in the display. 5-2. Use the VALUE/ENTER knob to select "1080/59.94i," "1080/50i," "720/59.94p," or "720/50p." 5-3. Press the VALUE/ENTER knob to confirm the selection. The video signal is o ...

  • Roland VC-300HD - page 25

    25 Connecting Attaching the Rubber Feet (included) Please attach the feet as necessary; for example, when using the VC-300HD/VC-200HD without mounting it in a rack. Remove the double-sided tape from the rubber feet, then affix them as shown in the figure below. * The rubber feet are arranged onto one pad. Please remove from the pad to use them. * W ...

  • Roland VC-300HD - page 26

    26 Basic Operations 941 ● Once the connections have been completed (p. 14), turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. 942 ● This unit is equipped with a protection circuit. A brief interval (a few seconds) afte ...

  • Roland VC-300HD - page 27

    Basic Operations 27 This unit has several sound input connectors: AUDIO INPUT connectors, i.LINK connector, and HD-SDI connector (VC-300HD only). At the factory settings, the audio input connector appropriate for the video selected under "Selecting the video input connector" (p. 26) is selected. Use the following procedure to manually sel ...

  • Roland VC-300HD - page 28

    Basic Operations 28 The VC-300HD/VC-200HD can easily output test patterns or test tones. 1 Press the OUTPUT button until "390: Test Pattern" or "391: Test Tone" is shown in the display Press the PAGE button once to display the test pattern. Press the PAGE button twice to display the test tone. The OUTPUT button lights, and the s ...

  • Roland VC-300HD - page 29

    Basic Operations 29 The display shows the status of the device. It also shows the menu screens for the various settings. * The display may be difficult to read depending on the angle from which the unit is viewed. The character contrast on the display and brightness of the backlight are adjusted with the "900: LCD Contrast" and "901: ...

  • Roland VC-300HD - page 30

    Basic Operations 30 The Menu screen is shown on the display when the MENU button is pressed. Various settings for the VC-300HD/ VC-200HD are performed on the Menu screen. * See “Menus and settings” (p. 32) for items displayed on the Menu screen. Item Selection When the VALUE/ENTER knob is turned while an item number is blinking, the item number ...

  • Roland VC-300HD - page 31

    31 Appendices ...

  • Roland VC-300HD - page 32

    32 Menus and settings * See Menu Display and Operation (p. 30) for menu operations. 100–162 Input Parameter * The values enclosed in a [box] are the factory defaults. Item Number Item Name Description and Available Settings 100 Video Source Specifies connector from which video is to be input. [i.LINK]: Selects the i.LINK connector. COMPONENT: Sel ...

  • Roland VC-300HD - page 33

    33 Menus and settings 100–162 Input Parameter (continued) 200–275 Processing Parameter * The values enclosed in a [box] are the factory defaults. Item Number Item Name Description and Available Settings 161 In Ch1&2 NomLv Sets the input Nominal level for AUDIO INPUT connector CH1 and CH2. +4dBu, -2dBu, -4dBu, -10dBu: Larger numerical values ...

  • Roland VC-300HD - page 34

    34 Menus and settings 200–275 Processing Parameter (continued) * The values enclosed in a [box] are the factory defaults. * For items 201-212 and 220-224, please adjust while confirming on a video monitor. Item Number Item Name Description and Available Settings 210 Out Zoom Adjusts the magnification of the output video. 50–[100]–200%: Larger ...

  • Roland VC-300HD - page 35

    35 Menus and settings 200–275 Processing Parameter (continued) * The values enclosed in a [box] are the factory defaults. 300–391 Output Parameter * The values enclosed in a [box] are the factory defaults. * For items 350 and 351, please adjust while confirming on a monitor speaker. Item Number Item Name Description and Available Settings 274 U ...

  • Roland VC-300HD - page 36

    36 Menus and settings 300–391 Output Parameter (continued) Note: For item numbers 351, 353, and 354, please adjust whilee confirming with headphones. Note: The values enclosed in a [box] are the factory defaults. Item Number Item Name Description and Available Settings 390 Test Pattern Displays the test pattern. [Off]: No test pattern is displaye ...

  • Roland VC-300HD - page 37

    37 Menus and settings 400–452 SDI Parameter Note: The values enclosed in a [box] are the factory defaults. 900–999 System Parameter * The values enclosed in a [box] are the factory defaults. Item Number Item Name Description and Available Settings 400 SDI IN AudioCh Selects the channels to be used for conversion with "AUDIO PROCESSOR [CH A ...

  • Roland VC-300HD - page 38

    38 Input / Output Signal HDV (High Definition Video) is the standard term used for the format to record High-definition television (HDTV) onto DV tape used in digital video cameras. HDV uses MPEG-2 for video compression. DV uses a method that compresses each video frame individually, but HDV realizes high definition recording with the same data vol ...

  • Roland VC-300HD - page 39

    39 Installation and Maintenance The rack mounts fittings for this device can be installed or removed. Cautions regarding removing the rack mount fittings • Please use a Phillips screwdriver that fits the screw head (No. 2 screwdriver). If the screwdriver does not fit the screw head, then the screw head may become stripped. • To remove the screw ...

  • Roland VC-300HD - page 40

    40 Troubleshooting If damage is suspected, please check the following again. If the problem persists after checking the following, please consult with a service center (listed on the back of the warranty envelope) or the retailer from whom this device was purchased. No video is output ● Is the equipment properly connected? ➔ Check that all devi ...

  • Roland VC-300HD - page 41

    41 Main Specifications VC-200HD / VC-300HD: MULTI-FORMAT CONVERTER Video Input Format ❥ IEEE1394 (i.LINK) HDV: 1080/59.94i, 1080/50i, 720/59.94p, 720/50p DV: 480/59.94, 576/50 ❥ Component Y/Pb/Pr: 1080/59.94i, 1080/50i, 720/59.94p, 720/50p, 480/59.94p, 576/50p, 480/59.94i, 576/50i ❥ DVI-I Digital (RGB): 1600x1200/60Hz, 1400x1050/60/75Hz, 1280 ...

  • Roland VC-300HD - page 42

    Main Specifications 42 Video Connectors IEEE1394 Connector(i.LINK) 6-pin Type, conforms to IEEE1394, HDV standards, Same connector on front and rear ❥ COMPONENT Input Connector HD/SD Y/Pb/Pr BNC Type 75 ohms, BiLevel, TriLevel Sync ❥ DVI-I Input Connector DVI 29pin single link RGB (8 bit each) Digital RGB dot clock: 25-161MHz (VGA to UXGA) Anal ...

  • Roland VC-300HD - page 43

    Main Specifications 43 VC-200HD Block Diagram COMPONENT IN DVI - I IN SDI IN HD - SDI Y CH1 CH2 CH3 CH4 DIGITAL ANALOG Pb Pr Y CH1 CH2 CH3 CH4 DIGITAL ANALOG Pb Pr REF IN AUDIO IN ( BALANCED )( Embedded Audio ) ( Embedded Audio )( BALANCED ) SDI Rx MODULE SDI Tx MODULE TC TC FRONT REAR SDI OUT HD - SDI DVI - I OUT COMPONEN T OUT REF OUT AUDIO OUT D ...

  • Roland VC-300HD - page 44

    Main Specifications 44 VC-300HD Block Diagram VC-300HD AUDIO BLOCK DIAGRAM VC-200HD AUDIO BLOCK DIAGRAM 450 SDI OUT Audio Ch 331 AudioOutCh3&4Lv 391 T est T one 160 AUDIO In Ch 160 AUDIO In Ch 150 Audio Source 400 SDI IN Audio Ch 170 DV In Audio Ch 330 AudioOutCh1&2Lv 150 Audio Source 170 DV In Audio Ch 351 Out Ch3&4 NomLv 350 Out Ch1&a ...

  • Roland VC-300HD - page 45

    Main Specifications 45 The following lists the video formats that can be output with the output connectors mounted on this device. indicates that the combination can be output. Output Format Support Chart Format/Output Connector i.LINK Connector COMPONENT OUT Connector DVI-I OUT Connector (digital) DVI-I OUT Connector (analog) HD-SDI OUT Connector ...

  • Roland VC-300HD - page 46

    46 Index Numerics 32 kHz .......................................................................... 27, 33 48 kHz ................................................................................ 33 A AC Inlet .............................................................................. 12 Audio Delay ............................................... ...

  • Roland VC-300HD - page 47

    47 This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC. For EU Countries For Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brou ...

  • Roland VC-300HD - page 48

    04564356 07-3-1N *04564356-01* ...

Manufacturer Roland Category TV Converter Box

Documents that we receive from a manufacturer of a Roland VC-300HD can be divided into several groups. They are, among others:
- Roland technical drawings
- VC-300HD manuals
- Roland product data sheets
- information booklets
- or energy labels Roland VC-300HD
All of them are important, but the most important information from the point of view of use of the device are in the user manual Roland VC-300HD.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Roland VC-300HD, service manual, brief instructions and user manuals Roland VC-300HD. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Roland VC-300HD.

Similar manuals

A complete manual for the device Roland VC-300HD, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Roland VC-300HD by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Roland VC-300HD.

A complete Roland manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Roland VC-300HD - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Roland VC-300HD, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Roland VC-300HD, that we can find in the current document
3. Tips how to use the basic functions of the device Roland VC-300HD - which should help us in our first steps of using Roland VC-300HD
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Roland VC-300HD
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Roland VC-300HD in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Roland VC-300HD?

Use the form below

If you did not solve your problem by using a manual Roland VC-300HD, ask a question using the form below. If a user had a similar problem with Roland VC-300HD it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)