English dropdown-ico

Manual Broan HRV90H

26 pages 2.85 mb
Download

Go to site of 26

Summary
  • Broan HRV90H - page 1

    INST ALLA TION INSTR UCTIONS HR V90H AND ER V90HC RESIDENTIAL USE ONL Y READ AND SA VE THESE INSTR UCTIONS 06010C re v . E Model no.: HR V90HT (HR V with por ts on top) Model no.: HR V90HS (HR V with por ts on sides) Model no.: ER V90HCT (ER V with por ts on top) Model no.: ER V90HCS (ER V with por ts on sides) VB0082 VB0080 VB0079 VB0081 ...

  • Broan HRV90H - page 2

    ABOUT THIS MANU AL Because of the large amount of models cov ered by this pub lication, the illustrations are typical ones. Some details of y our unit may be slightly diff erent than the ones shown. Please take note that this man ual uses the follo wing symbols to emphasize par ticular information: NO TE: Indicates supplementary information needed ...

  • Broan HRV90H - page 3

    1.0 T ECHNICAL D ATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6 1.1 A IR D ISTRIBUTION (N ORMAL O PERA TION ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.2 A IR D ISTRIBUTION (R ECIRCULA TION OR D EFROST M ODE ...

  • Broan HRV90H - page 4

    HR V ER V 1. TECHNICAL D A T A 1.1 A IR D ISTRIBUTION (N ORMAL O PERA TION ) VF0039 VF0038 HR V ER V 1.2 A IR D ISTRIBUTION (R ECIRCULA TION OR D EFROST M ODE ) VF0036 VF0037 Celcius (°C) -5 to -27 -27 and less F ahrenheit (°F) 23 to -17 -17 and less Defrosting (min.) 9 10 Operation time (min.) between each defrost cycle 23 22 Outside T emperatur ...

  • Broan HRV90H - page 5

    1.4.1 HR V U NITS 1. TECHNICAL D A T A (CONT’D) 1.4 P ERFORMANCE C HARTS V entilation Performance NO TE: A LL SPECIFICA TIONS ARE SUBJECT T O CHANGE WITHOUT NO TICE . SUPPL Y POWER SENSIBLE APP ARENT LA TENT RECOVER Y/ TEMPERA TURE NET AIR FLOW CONSUMED RECOVERY SENSIBLE MOISTURE WATT S EFFICIENCY EFFECTIVENESS TRANSFER 68 82 11 6 11 0 66 65 59 5 ...

  • Broan HRV90H - page 6

    1. TECHNICAL D A T A (CONT’D) 1.5 D IMENSIONS 1.5.1 D IMENSIONS FOR P ORTS ON S IDES U NITS 2½” (64 mm) 12 16 ” (310 mm) 16 ¼” (413 mm) 3 4’ ’ (102 mm) 6’ ’ (152 mm) 22 16 ” (574 mm) 23 ¾” (603 mm) 9 VK0056 19 16 ” (503 mm) 13 4’ ’ (102 mm) 6’ ’ (152 mm) 2” (51 mm) 13¾” (349 mm) 22 16 ” (574 mm) 9 27 16 ” ( ...

  • Broan HRV90H - page 7

    2.3 S IMPLIFIED I NST ALLA TION (C ONNECTION T O A FORCED AIR SYSTEM ) 2. TYPICAL INST ALLA TIONS Installations ma y vary according to the type of unit and the por ts configuration (top or sides). Use the f ollowing illustrations as guidelines to help you decide on ho w the unit will be installed. All the units should be hung from the joists. In e ...

  • Broan HRV90H - page 8

    2. TYPICAL INST ALLA TIONS (CONT’D) The ER V units are created to meet specific requirements related to geographical locations . T ake a look at the map below; the shaded area shows the limits where the ER V unit can be installed. Howe ver , there is no geographical limitation f or installing an HR V unit. NO TE: The ER V unit is designed to assi ...

  • Broan HRV90H - page 9

    - 9 - 3. INST ALLA TION 3 .1 I NSPECT THE C ONTENTS OF THE B OX • Inspect the e xter ior of the unit f or shipping damage. Ensure that there is no damage to the door , door latches, power cord, etc . • Remov e and discard the 2 transpor t brac kets ( A ) and open the door . Discard the styrofoam fillers (ER V units only) and remov e the hardwar ...

  • Broan HRV90H - page 10

    - 10 - 3. INST ALLA TION (CONT’D) 3.5 P LANNING OF THE D UCTWORK • K eep it simple. Plan f or a minimum of bends and joints. • K eep the length of insulated ducts to a minimum. • Do not ventilate cr awl spaces or cold rooms. Do not attempt to recov er the exhaust air from a dryer or a range hood. This would cause clogging of the filters and ...

  • Broan HRV90H - page 11

    3. INST ALLA TION (CONT’D) 3.6 I NST ALLING THE D UCTW ORK AND R EGISTERS ( CONT ’ D ) 3.6.2 C ENTRAL D RA W P OINT S YSTEM ( AS ILLUSTRA TED IN S ECTION 2.2) Stale air exhaust ductw ork Same as f or Fully Ducted System, descr ibed on point 3.6.1. Fresh air distribution ductw ork There are 2 methods f or connecting the unit to the fur nace/air ...

  • Broan HRV90H - page 12

    3.6 I NST ALLING THE D UCTW ORK AND R EGISTERS ( CONT ’ D ) 3.6.3 S IMPLIFIED I NST ALLA TION ( AS ILLUSTRA TED IN S ECTION 2.3) There are 2 methods f or connecting the unit to the fur nace/air handler : Method 1: Supply-return connection Method 2A: Return-return without Method 2B: Return-return with A utomatic fresh air bypass A utomatic fresh a ...

  • Broan HRV90H - page 13

    Rigid ducts Use a small length of fle xible duct to connect the rigid duct to the por ts in order to av oid vibration transmissions. Use tie-wraps to perf or m connections. 3.7 C ONNECTING THE DUCTS TO THE UNIT Insulated flexible ducts Use the f ollowing procedure f or connecting the insulated flexib le ducts to the por t of the unit ( Exhaust air ...

  • Broan HRV90H - page 14

    3.8 I NST ALLING THE T ANDEM ® T RANSITION K IT ( CONT ’ D ) 3.8.1 C ONNECTION T O T ANDEM ® TRANSITION 1. F or each duct, pull back the insulation to e xpose the interior flexible duct. 2. Connect the interior flexib le duct to the smaller par t of the T andem® transition (5’ ’ ov al) using a tie wrap . 3. Pull the insulation ov er the jo ...

  • Broan HRV90H - page 15

    3.8 I NST ALLING THE T ANDEM ® T RANSITION K IT ( CONT ’ D ) 3.8.4 C ONNECTING T ANDEM ® TRANSITION TO THE D UAL EXTERIOR H OOD ( CONT ’ D ) 2. Join the end of the T andem® transition to the rear of the exterior backplate . Secure with 2 Xmas tree pins and seal properly with duct tape. 3. Using 4 #8 x 1 1 ¼ 2 ” screws , mount the the exte ...

  • Broan HRV90H - page 16

    3. INST ALLA TION (CONT’D) 3.9 I NST ALLING 2 E XTERIOR H OODS Choose an appropriate location to install the exterior hoods: • There must be a minimum distance of 6 f eet (1.8 m) between the hoods to a void cross-contamination • There must be a minimum distance of 18 inches (457 mm) from the g round Make sure the intak e hood is at least 6 fe ...

  • Broan HRV90H - page 17

    4. CONTROLS 4.1 I NTEGRA TED C ONTROL All units are equipped with an integrated control, located under the unit, in front of the electrical compar tment. Use the push button ( 1 ) to control the unit. The LED ( 2 ) will then shows on which mode the unit is in. W ARNING Risk of electric shock. Before perf orming any maintenance or servicing, always ...

  • Broan HRV90H - page 18

    4. CONTROLS (CONT’D) 4.2.1 E LECTRICAL C ONNECTION T O VT4W M AIN W ALL C ONTROL NO C NC I OC OL Y R G B B G OC MAIN WALL CONTROL LITE-TOUCH BRONZE and SIMPLE TOUCH BRONZE REAR VIEW G B Y VE0101A M AIN W ALL CONTROL VT4W REAR VIEW 4.2 E LECTRICAL C ONNECTION T O O PTIONAL W ALL C ONTROLS ( CONT ’ D ) 4.2.2 E LECTRICAL C ONNECTION T O O PTIONAL ...

  • Broan HRV90H - page 19

    4. CONTROLS (CONT’D) 4.4 O PTIONAL A UXILIAR Y W ALL C ONTROLS O PERA TION 4.4.1 20-M INUTE L IGHTED P USH -B UTT ON T IMER Set the push-button timer to ON. The fan motors will then operate at high speed f or 20 minutes and the indicator will light up . T o stop activ ation, push one time; the unit will then get back to previous selection. 4.4.2 ...

  • Broan HRV90H - page 20

    6. WIRING DIA GRAM W ARNING Risk of electrical shocks. Before performing an y maintenance or servicing, al ways disconnect the unit fr om its power source. ! Field wiring remote control (see notes 3 & 4) 120 V, 60 Hz W1 J5 J7 J6 J4 ELECTRONIC ASSEMBLY 1 2 3 1 2 1 2 1 2 3 1 2 3 4 1 2 1 2 3 4 5 1 2 3 4 5 J8 J9 J11 J10 1 2 J12 J13 J14 10 9 8 7 6 5 ...

  • Broan HRV90H - page 21

    7.1 W HA T Y OU N EED T O B ALANCE THE U NIT • A magnehelic gauge capable of measuring 0 to 0.5 inch of water (0 to 125 P a) and 2 plastic tubes. • The balancing char t located on the unit door . 7.2 P RELIMINAR Y S T AGES T O B ALANCE THE U NIT • Seal all the unit ductwork with tape. Close all windows and doors . • T urn off all exhaust de ...

  • Broan HRV90H - page 22

    8. CONNECTING THE DRAIN (HR V UNITS ONL Y) VO0091 VO0093 VO0092 T o drain In order to keep the dr ain pan intact, hand tighten the 2 plastic drain fittings to the unit door using the gaskets and n uts as shown. Cut 2 sections of plastic tubing, about 12” (305 mm) long and attach them to each drain fitting. Join the 2 shor t sections to the «T» ...

  • Broan HRV90H - page 23

    3. Lift both f oam filters brack et ( 1 ) and remov e the f oam filters from the core. While holding the core, rotate the 2 core retainers ( 2 ) and slide out the core from the unit. 2. Unlatch the door and open it. Clean the inner side of the door with a damp cloth, then wipe with a dr y one. Disengage the door from its hinge by sliding it from le ...

  • Broan HRV90H - page 24

    9. MAINTENANCE (CONT’D) 9.1 S EMI -A NNU AL M AINTENANCE ( CONT ’ D ) 4. Clean the inside walls of the unit with a clean damp cloth, then wipe with a clean dry one. 5. W ash the 2 core filters under hot water with mild soap . Rinse thoroughly and let dr y completely bef ore reinstalling on the core. 6. Remov e the dust on the core using a vacuu ...

  • Broan HRV90H - page 25

    - 25 - VL0019 10. SER VICE P ARTS I TEM D ESCRIPTION P ART N UMBER HR V90HS HR V90HT ER V90HCS ER V90HCT ( PORTS ON SIDES )( PORTS ON TOP )( PORTS ON SIDES )( PORTS ON T OP ) 1O V AL PORT ( FITS 5” DIAMETER DUCTS ) 16040 1 1 1 1 2D OOR LA TCH WITH SCREWS 16035 2 2 2 2 3O V AL PORT WITH INTEGRA TED BALANCING DAMPER 16041 2 2 2 2 4M OTO R & WHE ...

  • Broan HRV90H - page 26

    11. TROUBLESHOO TING Prob lems P ossible causes Y ou should try this 1. Unit does not work. • The circuit board may be def ective. • Unplug the unit. Disconnect the main control and the auxiliary control(s) (if need be). Jump G and B terminals. Plug the unit b a c k and w ait about 10 seconds. If the motors r un on high speed and the damper ope ...

Manufacturer Broan Category Air Cleaner

Documents that we receive from a manufacturer of a Broan HRV90H can be divided into several groups. They are, among others:
- Broan technical drawings
- HRV90H manuals
- Broan product data sheets
- information booklets
- or energy labels Broan HRV90H
All of them are important, but the most important information from the point of view of use of the device are in the user manual Broan HRV90H.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Broan HRV90H, service manual, brief instructions and user manuals Broan HRV90H. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Broan HRV90H.

Similar manuals

A complete manual for the device Broan HRV90H, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Broan HRV90H by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Broan HRV90H.

A complete Broan manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Broan HRV90H - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Broan HRV90H, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Broan HRV90H, that we can find in the current document
3. Tips how to use the basic functions of the device Broan HRV90H - which should help us in our first steps of using Broan HRV90H
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Broan HRV90H
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Broan HRV90H in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Broan HRV90H?

Use the form below

If you did not solve your problem by using a manual Broan HRV90H, ask a question using the form below. If a user had a similar problem with Broan HRV90H it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)