English dropdown-ico

Manual Tektronix VM700T

16 pages 0.56 mb
Download

Go to site of 16

Summary
  • Tektronix VM700T - page 1

    VM700 T (turbo) V ideo Measurement Set Option 11 P AL V ideo Measurements M any capabilities in one instrument – Digitizing waveform monitor – Digitizing vectorscope – Picture Display – Group delay and frequency response – Noise measurement set – Automatic measurement set Auto mode – Unattended monitoring of P AL video signals from st ...

  • Tektronix VM700T - page 2

    modem to report measurement r esults or control a signal router . A relative to reference mode allows normalizing to a signal source or eliminate signal path errors from the desired measurement. Up to 2 video references can be stored in NVRAM. Additionally , a f te r downloading to a PC through the V M700T FTP driver , the video reference can be up ...

  • Tektronix VM700T - page 3

    Vertical interval test signals can be seen very clearly for additional analysis of the signal. These can be printed as support documentation for automatic measurement results. E ven a single horizontal synchronization pulse can be displayed at a high intensity . 0.5 0.0 Volts Sound-In-Sync Off Sound-In-Sync Off Precision Mode On Precision Mode On L ...

  • Tektronix VM700T - page 4

    Bar Line Time measurement. Chrominance to Luminance Gain and Delay measurement. MEASURE MODE 1,2 BAR LINE TIME A bsolute Relative M easurement Range Mode Mode Accuracy Accuracy B ar Level (b1 or Back Porch) 300 mV to 1.4 V ± 0.5% ± 0.2% S ync Level 50 mV to 600 mV ± 0.5% ± 0.2% S ync to Bar T op 350 mV to 2 V ± 0.5% ± 0.2% S ync/Bar Ratio 10% ...

  • Tektronix VM700T - page 5

    Chrominance Non-Linearity measurement. Color Bar measurement. Luminance Level (mV ) Luminance Level (mV ) Chrominance Level (mV ) Chrominance Level (mV ) Chrominance Phase (deg) Chrominance Phase (deg) Gray Gray Yellow Yellow Cyan Cyan Green Green Magenta Magenta Red Red Blue Blue Black Black 0.0 500.0 1000.0 0.0 500.0 1000.0 0.0 500.0 1000.0 0.0 5 ...

  • Tektronix VM700T - page 6

    Frequency Response and Group Delay measurement using Sin X/X. Horizontal Timing measurement. M EASURE MODE (continued) FREQUENCY RESPONSE AND GROUP DELA Y A bsolute Relative M easurement Range Mode Mode A ccuracy Accuracy F requency Response to 5 MHz ± 40 dB ± 1.0 dB ± 0.3 dB to 6 MHz ± 40 dB ± 2.0 dB ± 0.6 dB Group Delay to 5 MHz ± 1.0 µs ...

  • Tektronix VM700T - page 7

    LINE FREQUENCY M easurement Range Accuracy L ine Frequency ± 3% ± 0.1% F ield Frequency ± 3% ± 0.1% LUMINANCE NON-LINEARITY Absolute Relative M easurement Range Mode Mode A ccuracy Accuracy L uminance Non-Linearity 0 to 100% ± 0.4% ± 0.2% K-factor measurement. Luminance Non-Linearity measurement. Luminance Non Linearity (%) Luminance Non Line ...

  • Tektronix VM700T - page 8

    VERTICAL BLANKING M easurement Range Absolute Mode Accuracy E qualizing Pulse Width 80 ns to 1 µs ± 10 ns B road Pulse Width 80 ns to 1 µs ± 10 ns V ertical Blanking Field 1 19 to 30 lines NA Vertical Blanking Field 2 19 to 30 lines NA Noise Spectrum measurement. V e rtical Blanking display . M EASURE MODE (continued) NOISE SPECTRUM M easuremen ...

  • Tektronix VM700T - page 9

    AMPLITUDE AND PHASE MEASUREMENTS (continued) M easurement Range Accuracy ITS Element Standard D ifferential Gain 0 to +100% ± 0.3% D2 CCIR Rec. 569 ( Peak and p-p) (0% nominal) D ifferential Phase 0 to 360 deg ± 0.3 deg D2 CCIR Rec. 569 (Peak and p-p) (0 deg nominal) FREQUENCY RESPONSE MEASUREMENTS M easurement Range Accuracy ITS Element Standard ...

  • Tektronix VM700T - page 10

    Unified Unweighted filter response curve per CCIR Recommendation 567. 0 –5 5 08 M Hz d BV –5 – 10 – 15 –2 0 –2 5 –3 0 –3 5 –4 0 – 45 –5 0 1 234 5 67 U nified Luminance weighted filter response curve per CCIR Recommendation 567. 0 – 14 05 MHz dBV .5 1 1.5 2 3 4 –12 – 10 –8 – 6 –4 – 2 2.5 3.5 4.5 Chrominance Weight ...

  • Tektronix VM700T - page 11

    Measur ement r esults are displayed in an easy-to-read format indicating the time, signal source, measurement, and whether the measured value exceeded caution (*) or alarm (**) limits. 11 VM700T Video Measurement Set C hannel A System Def ault 07-A ug-96 19:06:58 VM700T Video Measurement Set System Default Violated Limits Lower Upper Source ID ---- ...

  • Tektronix VM700T - page 12

    Measurement methods The following paragraphs specify the methods for each Option 11 measurement. Where appropriate, reference is made to the relevant CCIR recommendation. Line blanking timing measurements Color Burst Duration: Measured between the half-amplitude points of the burst chrominance envelope. Result expressed as the number of cycles betw ...

  • Tektronix VM700T - page 13

    Other timing measurements B ar Rise T ime: M easured between the 10% and 90% points on the leading edge of bar . See element B2. A mplitude and phase measurements Sync Amplitude Error: Measured as the difference b etween the sampled sync pulse amplitude and a nominal 300 mV amplitude. Result expressed as a % of the nominal 3 00 mV . Sign is positiv ...

  • Tektronix VM700T - page 14

    C/L Gain Inequality: Measured as the difference between the sampled peak-to-peak ampli- tude of the 700 mV (nominal) chrominance packet (G1 or G2) and the sampled amplitude of the luminance bar (also nomi- nally 700 mV). Result expressed as a % of sampled bar amplitude. Sign is positive if the chromi- nance amplitude is greater than the luminance a ...

  • Tektronix VM700T - page 15

    Frequency response measurements M ultiburst Flag Amplitude: Measured from the center point of the flag top to the ensuing bottom of the flag. Result e xpressed as % of sampled bar a mplitude. See element C1 and CCIR Recommendation 567. M ultiburst Amplitude (five packets): Measured as the peak-to-peak amplitude of each of the first five multiburst ...

  • Tektronix VM700T - page 16

    Contact T ektronix: A SEAN / Australasia / Pakistan ( 65) 6356 3900 A ustria + 41 52 675 3777 B alkan, Israel, South Africa and other ISE Countries + 41 52 675 3777 B elgium 0 7 81 60166 B razil & South America 5 5 (11) 3741-8360 Canada 1 (800) 661-5625 Central East Europe, Ukraine and Baltics +41 52 675 3777 Central Europe & Greece +41 52 ...

Manufacturer Tektronix Category Stereo Receiver

Documents that we receive from a manufacturer of a Tektronix VM700T can be divided into several groups. They are, among others:
- Tektronix technical drawings
- VM700T manuals
- Tektronix product data sheets
- information booklets
- or energy labels Tektronix VM700T
All of them are important, but the most important information from the point of view of use of the device are in the user manual Tektronix VM700T.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Tektronix VM700T, service manual, brief instructions and user manuals Tektronix VM700T. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Tektronix VM700T.

Similar manuals

A complete manual for the device Tektronix VM700T, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Tektronix VM700T by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Tektronix VM700T.

A complete Tektronix manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Tektronix VM700T - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Tektronix VM700T, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Tektronix VM700T, that we can find in the current document
3. Tips how to use the basic functions of the device Tektronix VM700T - which should help us in our first steps of using Tektronix VM700T
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Tektronix VM700T
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Tektronix VM700T in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Tektronix VM700T?

Use the form below

If you did not solve your problem by using a manual Tektronix VM700T, ask a question using the form below. If a user had a similar problem with Tektronix VM700T it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)