English dropdown-ico

Manual Liebert SL-14050

16 pages 0.17 mb
Download

Go to site of 16

Summary
  • Liebert SL-14050 - page 1

    SGH Steam Generating Humidifier Installation and Operation Guide IMPORTANT: Read and save this guide for future reference. This guide to be left with equipment owner. SL-14050 Form # 99-428 Rev. 1 / 150-1633 Rev. A ...

  • Liebert SL-14050 - page 2

    Table Of Contents INSTALLATION 1 RECEIVING & UNPACKING EQUIPMENT ................................1 PRE-INSTALLATION CHECKPOINT ...................................1 BASIC HUMIDIFIER CONFIGURATION ..................................1 LOCATION & MOUNTING .........................................1 HUMIDIFIERS .................................... ...

  • Liebert SL-14050 - page 3

    INSTALLATION RECEIVING & UNPACKING EQUIPMENT 1. Check packing slip to ensure ALL material has been delivered. 2. All material shortages are to be reported to Liebert within 48 hours from receipt of goods. Liebert assumes no responsibility for any material shortages beyond this period. 3. Inspect shipping boxes for damage and note on shipping wa ...

  • Liebert SL-14050 - page 4

    to clearances required for plumbing, electrical, and control entrances. The clearance dimensions shown in this manual are for reference only and are the minimum required for maintenance of the humidifier. Local and National Codes should be consulted prior to final location and installation of the humidifier. Liebert can not accept responsibility fo ...

  • Liebert SL-14050 - page 5

    FRONT WALL SIDE STEAM CONDENSATE A 005-030 3.2" (8.0cm) 050-100 3.2" (8.0cm) A POWER AND CONTROL WIRING FROM HUMIDIFIER 10-20 050-100 3.2” (8 cm) 3. All SGH blower packs consist of a steel cabinet containing: blower/motor powered by voltage directly from the humidifier, fuse, relay, speed select switch, stainless steel steam distributor ...

  • Liebert SL-14050 - page 6

    5. Exercise extreme caution when installing in fiber glass or internally lined ducts. 6. High positive or negative static pressure ducts or plenums have special requirements. High positive static pressure ducts may require the unit to be fitted with a fill cup extension kit. High negative static pressure ducts will likely require the drain rate of ...

  • Liebert SL-14050 - page 7

    10. Any distributor longer than 3 feet (1 meter) should be supported at its end with a threaded rod through top or bottom of duct. See Figure #10. 11. It is recommended that single distributors are mounted near the bottom of the duct to ensure the steam is dispersed into the majority of the air flow. See Figure #12. 12. Using duct mounting template ...

  • Liebert SL-14050 - page 8

    5. ALWAYS supply and install a shut off valve in the water supply line dedicated to the humidifier to facilitate servicing. Use ½ "O D copper to within 4 feet of the humidifier. Reduce copper to 3/8" OD and connect to the factory-supplied 3/8" olive compression fitting under the humidifier. DRAIN LINE 1. Humidifier is equipped with ...

  • Liebert SL-14050 - page 9

    3. Liebert steam supply hose or field-supplied piping should be sloped downwards from the steam distributors to the humidifier. Slope should be at least 2" in 12" to promote condensate runback. See Figure #18. If this slope is not possible, condensate must be removed before the distributor. See Figure #19. 4. Minimize the length of steam ...

  • Liebert SL-14050 - page 10

    ACCESSORIES - FILL CUP EXTENSION KIT(S) 1. The SGH humidifier is an electrode humidifier. It produces steam at atmospheric pressure. Pressure head must develop to push steam through supply line and into air duct. 2. Combined resistance of duct positive static pressure and steam line resistance creates a small pressure head in steam cylinder. Total ...

  • Liebert SL-14050 - page 11

    impeding condensate flow when duct pressures are below atmosphere. 6. The condensate line can go to either of two large holes in the fill cup cover on top of humidifier. 7. It is not necessary to return the condensate to the humidifier. 8. Long condensate runs (more than twenty feet) should be sloped well and be constructed out of ½ " nominal ...

  • Liebert SL-14050 - page 12

    information is relevant to all controls, factory supplied or otherwise. A, B and C (described below) are to be wired in series (only one path for current) across terminals 8 and 10 on the low voltage control terminal strip, or replaced with a jumper wire for constant operation (see Figure #27). Caution: If any control field wiring touches ground me ...

  • Liebert SL-14050 - page 13

    4. The modulation signal must increase from minimum toward maximum as sensed RH (actual RH) drops below desired RH (%RH setpoint). In response, humidifier ’ s steam output will increase from minimum toward maximum. When humidifier ’ s steam output (lbs/hr) matches humidification load (lbs/hr), modulation signal will stabilize. 5. Field-wiring c ...

  • Liebert SL-14050 - page 14

    satisfied and stops again. The resultant short-cycling is easily overcome. A manual capacity adjustment potentiometer ( “ pot ” ) is provided on the SGH main pc board for that purpose. It is marked “ CAPACITY ADJUST ” and is adjustable from 25 to 100% of rating. Modulation Control The SGH humidifier, utilizing modulation control, does not h ...

  • Liebert SL-14050 - page 15

    LIMITED WARRANTY Liebert Corporation (hereinafter collectively referred to as THE COMPANY), warrant for a period of two years from date of shipment, that THE COMPANY ’ s manufactured and assembled products, not otherwise expressly warranted (with the exception of the cylinder) are free from defects in material and workmanship. No warranty is made ...

  • Liebert SL-14050 - page 16

    Model # :_________________________ Serial # :__________________________ Cylinder # :_________________________ Cylinder Last Replaced: _________________________ MTH/DAY/YR _________________________ MTH/DAY/YR _________________________ MTH/DAY/YR PRINTED IN CANADA LIEBERT CORPORATION 1050 Dearborn Drive, P.O. Box 29186 Columbus, Ohio 43229 Tel: (614) ...

Manufacturer Liebert Category Blowtorch

Documents that we receive from a manufacturer of a Liebert SL-14050 can be divided into several groups. They are, among others:
- Liebert technical drawings
- SL-14050 manuals
- Liebert product data sheets
- information booklets
- or energy labels Liebert SL-14050
All of them are important, but the most important information from the point of view of use of the device are in the user manual Liebert SL-14050.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Liebert SL-14050, service manual, brief instructions and user manuals Liebert SL-14050. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Liebert SL-14050.

Similar manuals

A complete manual for the device Liebert SL-14050, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Liebert SL-14050 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Liebert SL-14050.

A complete Liebert manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Liebert SL-14050 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Liebert SL-14050, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Liebert SL-14050, that we can find in the current document
3. Tips how to use the basic functions of the device Liebert SL-14050 - which should help us in our first steps of using Liebert SL-14050
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Liebert SL-14050
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Liebert SL-14050 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Liebert SL-14050?

Use the form below

If you did not solve your problem by using a manual Liebert SL-14050, ask a question using the form below. If a user had a similar problem with Liebert SL-14050 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)