English dropdown-ico

Manual Hobart 6614 ML-134050

12 pages 0.91 mb
Download

Go to site of 12

Summary
  • Hobart 6614 ML-134050 - page 1

    N S T R U C T I O N S I FORM 34527 Rev. A (Sept. 2001) MODEL 6614 MEA T SA W MODEL 6614 ML-134096 Previous models covered by this manual: 6614 ML-134050 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com ...

  • Hobart 6614 ML-134050 - page 2

    –2– Installation, Operation, and Care of MODEL 6614 MEA T SA W SA VE THESE INSTRUCTIONS GENERAL The 6614 Meat Saw is rugged, durable, and easy to clean. The saw is equipped with a water resistant 3 HP electric motor and direct gear drive transmission that provides a blade speed of 3500 feet per minute. The carriage (Fig.1) has stainless steel b ...

  • Hobart 6614 ML-134050 - page 3

    –3– INST ALLA TION UNPACKING AND ASSEMBLY Immediately after unpacking the meat saw, check for possible shipping damage. If the meat saw is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, test the electrical service to make sure it agrees with the specifications on the m ...

  • Hobart 6614 ML-134050 - page 4

    – 4 – UPPER PULLEY COVER (Stainless Steel) The stainless steel upper pulley cover (Fig. 5) should be installed on the two hinge pins of the stainless steel upper pulley baffle and securely latched during saw use. To remove the stainless steel upper pulley cover for cleaning, unlatch and open the stainless steel upper pulley cover; then, lift st ...

  • Hobart 6614 ML-134050 - page 5

    – 5 – LOWER PULLEY The lower pulley is assembled on the lower pulley shaft. The latch on the lower pulley should be seated in the groove of the pulley shaft (Fig. 7). The lower pulley can be removed after the blade has first been loosened and removed and the lower pulley latch is moved out of the groove of the lower pulley shaft. UPPER PULLEY T ...

  • Hobart 6614 ML-134050 - page 6

    – 6 – SCRAP TRAY During use, the scrap tray should be installed between the left-hand table and the carriage support (Fig. 9). The scrap tray slides into place, resting on the frame between the carriage support and table. The angled side of the scrap tray is located nearest the blade. Fig. 9 CARRIAGE In use, the carriage can roll back and forth ...

  • Hobart 6614 ML-134050 - page 7

    – 7 – PL-40838-1 LOWER GUIDE HOLDER LOWER BLADE GUIDE ASSEMBL Y LOWER BLADE GUIDE The lower blade guide assembly fits in the lower guide holder (Fig. 12). The blade fits in the slots of both the steel saw blade guide and the plastic guide. When the right table is removed and the plastic guide is hinged up, the lower blade guide assembly can be ...

  • Hobart 6614 ML-134050 - page 8

    – 8 – ELECTRICAL CONNECTIONS WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON. A T A D L A C I R T C E L E l e ...

  • Hobart 6614 ML-134050 - page 9

    – 9 – OPERA TION SAFETY DEVICES INCORPORATED IN THIS SAW MUST BE IN THEIR CORRECT OPERATING POSITIONS ANYTIME THE SAW IS IN USE. SAFETY FEATURES Upper Guide and Guard Assembly Before turning the saw on, raise or lower the upper guide and guard assembly by grasping the hand knob and sliding up or down so the cutting zone is only as high as neces ...

  • Hobart 6614 ML-134050 - page 10

    – 10 – GAUGE PLATE When making several cuts of the same thickness (or when using the pusher plate), set the gauge plate as desired (Fig. 14) by pushing the lock lever and sliding the gauge plate to the thickness you want. A reference scale on the table indicates the thickness of cut. If the gauge plate is not needed, you may release the lock le ...

  • Hobart 6614 ML-134050 - page 11

    – 11 – CLEANING AND SANITIZING WARNING : DISCONNECT ELECTRICAL POWER AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON BEFORE CLEANING THIS MACHINE. The saw must be thoroughly cleaned and sanitized: Before first use; After each day's operation; Anytime it is not to be used for an extended period of time; or ...

  • Hobart 6614 ML-134050 - page 12

    – 12 – MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON. LUBRICATION The motor has permanently lubricated ball bearings and requires no additional lubrication. The slide bar for the upper guide and guard assembly also requires no lubrication. After cleani ...

Manufacturer Hobart Category Saw

Documents that we receive from a manufacturer of a Hobart 6614 ML-134050 can be divided into several groups. They are, among others:
- Hobart technical drawings
- 6614 ML-134050 manuals
- Hobart product data sheets
- information booklets
- or energy labels Hobart 6614 ML-134050
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hobart 6614 ML-134050.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hobart 6614 ML-134050, service manual, brief instructions and user manuals Hobart 6614 ML-134050. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hobart 6614 ML-134050.

Similar manuals

A complete manual for the device Hobart 6614 ML-134050, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hobart 6614 ML-134050 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hobart 6614 ML-134050.

A complete Hobart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hobart 6614 ML-134050 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hobart 6614 ML-134050, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hobart 6614 ML-134050, that we can find in the current document
3. Tips how to use the basic functions of the device Hobart 6614 ML-134050 - which should help us in our first steps of using Hobart 6614 ML-134050
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hobart 6614 ML-134050
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hobart 6614 ML-134050 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hobart 6614 ML-134050?

Use the form below

If you did not solve your problem by using a manual Hobart 6614 ML-134050, ask a question using the form below. If a user had a similar problem with Hobart 6614 ML-134050 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)