Manual Jet Tools JJ-8CS

28 pages 0.95 mb
Download

Go to site of 28

Summary
  • Jet Tools JJ-8CS - page 1

    OWNER’S MANUAL JJ-8CS W oodworking Jointer JET EQUIPMENT & TOOLS, INC. P .O. BOX 1349 Phone:253-351-6000 A WMH Company Auburn, W A 98071-1349 Fax: 1-800-274-6840 www .jettools.com e-mail jet@jettools.com M-708458 06/01 ...

  • Jet Tools JJ-8CS - page 2

    2 W arranty & Service The JET Group warrant s every product it sells. If one of our tools needs service or repair , one of our Authorized Repair S tations located throughout the United S tates can give you quick service. In most cases, any one of these JET Group Rep air S tations can authorize warranty repair , assist you in obtaining p arts, o ...

  • Jet Tools JJ-8CS - page 3

    3   W ARNING Wear eye protection. Always keep cutterhead and drive guards in place and in proper operating condition. Do not remove guard for rabbeting operations. Never make a jointing, planing, or rabbeting cut deeper than 1/8” . Always use hold-down/push blocks for jointing material narrower than 3”, or planing material thinner than 3? ...

  • Jet Tools JJ-8CS - page 4

    4 • Don’t overreach. Keep proper footing and balance at all times. • Maintain tools with care. Keep tools sharp and clean for best and safest performance. Follow instruc- tions for lubricating and changing accessories. • Always disconnect the machine from the power source before servicing. • Reduce the risk of unintentional starting. Make ...

  • Jet Tools JJ-8CS - page 5

    5 T able of Contents W arranty ......................................................................................................................................................... 2 W arnings ....................................................................................................................... ............................. 3-4 ...

  • Jet Tools JJ-8CS - page 6

    6 Levers and Controls 1. Handwheel for Outfeed T able 8. On/Off Switch 2. Outfeed T able 9. Rabbeting Ledge 3. Fence 10. T able Lock Knob 4. Fence Adjustment Handle 1 1. Fence T ilt Lock Handle 5. Cutter Guard 12. Fence Control Handle 6. Infeed T able 13. Belt Guard 7. Handwheel for Infeed T able 14. Dust Chute Specifications: JJ-8CS S tock Number ...

  • Jet Tools JJ-8CS - page 7

    7 Contents of Shipping Cartons Note: unit shipped in two cartons. Stand Carton 1. S tand with Motor 1. S tand Door 1. Dust Chute w/ Mounting Hardware Main Unit Carton 1. Bed Assembly w/ Fence 1. Cutter Guard 3. Mounting Bolts 3. 3/8" Lock Washers 1. Belt Guard 3. Hex Wrenches (3, 4 & 5mm) 2. Handwheels 2. Handles 2. V -Belts 1. Can of T ou ...

  • Jet Tools JJ-8CS - page 8

    8 Installing Bed to Stand 1. Use an assistant or hoist mechanism to place bed assembly on top of stand. Be sure identi- fication label on the bed faces the same direc- tion as the label on the stand (Fig. 1). 2. Line up two holes in top of stand with holes in bed assembly by viewing through access door in stand. 3. Attach bed assembly to stand with ...

  • Jet Tools JJ-8CS - page 9

    9 Assembling Knife-Setting Gauge 1. Place the two bases (A, Fig. 4) onto each end of the bar (B, Fig. 4). Snap the four E-rings (C, Fig. 4) into the grooves on the bar as shown. 90 ° Fence Adjustment Note : whenever making an adjustment to the fence, lift the fence up slightly after releasing the lock handle to avoid scratching the table. 1. Set i ...

  • Jet Tools JJ-8CS - page 10

    10 45 ° Fence Adjustment Note : Whenever making an adjustment to the fence, lift the fence up slightly after releasing the lock handle to avoid scratching the table. 1. Loosen lock handle (A, Fig. 7). Move the stop plate (B, Fig. 7) out of the way and position the fence at the 45 ° angle. Make sure the fence sits against the stop bolt (C, Fig. 7) ...

  • Jet Tools JJ-8CS - page 11

    11 5. When the outfeed table and blade number one are the same height, tighten table lock screw . 6. The knives must be parallel with the outfeed table. Bring the straight edge forward to the front of the outfeed table and confirm that blade number one is at the same height at the front of the table as it is at the back of the table. 7. If blade is ...

  • Jet Tools JJ-8CS - page 12

    12 Installing V -Belts 1. Disconnect the machine from the power source, unplug. 2. Remove the lock knob (A, Fig. 14) and belt guard (B, Fig. 14). 3. Place v-belts onto cutterhead pulley grooves and through opening in stand. 4. Pull v-belts down and place onto motor pulley (Fig. 15). If necessary , loosen the mounting screws (A, Fig. 15) and slightl ...

  • Jet Tools JJ-8CS - page 13

    13 Installing Access Cover 1. Install access cover by placing bottom of panel into access in stand and fastening by turning latch (Fig. 17). If the access door latch needs adjustment: 1. Remove the access door from the stand. 2. Loosen the hex lock nut (A, Fig. 17). Rotate the latch a quarter turn clockwise to tighten and counterclockwise to loosen ...

  • Jet Tools JJ-8CS - page 14

    14 Operation  W ARNING Keep all guards in place and in adjustment at all times during the cutting procedure! Keep hands away from the cutterhead! Do not pass hands directly over the cutterhead! The use of push sticks and/or handle pads are highly recommended when using the jointer! Failure to comply may cause serious injury! Jointing cuts or edg ...

  • Jet Tools JJ-8CS - page 15

    15 Jointing W arped Material If the work to be jointed is cupped or warped, take light, repetitive cuts until the surface is flat. Forc- ing the material flat against the table will still leave a warped piece after the cuts have been made.  W ARNING Never joint any material shorter than eight inches! The material may tip into the jointer’s thr ...

  • Jet Tools JJ-8CS - page 16

    16 Rabbet Cut  W ARNING Rabbeting requires the removal of the cutterhead guard. Use extreme caution when making rabbeting cuts and replace the guard immediately after completion! Failure to comply may cause serious injury! 1. Adjust the fence so that the distance between the end of the knives and fence is equal to the width of the rabbet (Fig. 2 ...

  • Jet Tools JJ-8CS - page 17

    17 6. Insert lock bar and screws and tighten to hold in place. Blades are set at the proper height when the top of the blade is 1/16" above the cutterhead. 7. Repeat for other two blades. 8. T o set the knives to the outfeed t able and to the same height in the cutterhead, see section titled “Leveling Outfeed T able to Cutterhead Knives” f ...

  • Jet Tools JJ-8CS - page 18

    18 Sharpening the Knives  W ARNING Blades are extremely sharp! Use caution when handling. Failure to comply may cause serious injury! 1. Disconnect the machine from the power source. 2. Remove the fence, blade guard and belt cover . 3. T o protect the infeed t able from scratches, par- tially cover the sharpening stone with paper . (Fig. 30) 4. ...

  • Jet Tools JJ-8CS - page 19

    19 T rouble-shooting e l b u o r Te s u a C e l b i s s o Pn o i t u l o S e h t n o d e v a c n o c s i k c o t s d e h s i n i F . d n e d e e f t u o e h t n a h t r e h g i h s i p i t e f i n K . e l b a t l e v e l s i t i o s e l b a t d e e f t u o e s i a R . p i t e f i n k h t i w s i k c o t s d e h s i n i f f o e d i s k c a B . e d i ...

  • Jet Tools JJ-8CS - page 20

    20 Fence Assembly ...

  • Jet Tools JJ-8CS - page 21

    21 Parts List for the JJ-8CS W oodworking Jointer Fence Assembly Index Part No. No. Description Size Qty . 1 ......... JC-F01 .............................. Fence Body ....................................................................... .................. 1 2 ......... JC-F02 .............................. Fence Link ............................ ...

  • Jet Tools JJ-8CS - page 22

    22 Bed Assembly ...

  • Jet Tools JJ-8CS - page 23

    23 Bed Assembly Index Part No. No. Description Size Qty . 1 ......... JC-T01 .............................. Base ............................................................................. .......................... 1 2 ......... JC-T02 .............................. Front T able ................................................................... ...

  • Jet Tools JJ-8CS - page 24

    24 Stand and Motor Assembly ...

  • Jet Tools JJ-8CS - page 25

    25 Stand and Motor Assembly Index Part No. No. Description Size Qty . 1 ......... JC-M01W .......................... S t and ....................................................................................................... 1 2 ......... JC-M02W .......................... Motor Mount ............................................................ ...

  • Jet Tools JJ-8CS - page 26

    26 Cutterhead Assembly ...

  • Jet Tools JJ-8CS - page 27

    27 Cutterhead Assembly Index Part No. No. Description Size Qty . 1 ......... JC-C01 ............................. Cutterhead ........................................................................ ...................... 1 2 ......... JC-C02 ............................. Bearing Housing .............................................................. ...

  • Jet Tools JJ-8CS - page 28

    28 Wiring Diagram ...

Manufacturer Jet Tools Category Biscuit Joiner

Documents that we receive from a manufacturer of a Jet Tools JJ-8CS can be divided into several groups. They are, among others:
- Jet Tools technical drawings
- JJ-8CS manuals
- Jet Tools product data sheets
- information booklets
- or energy labels Jet Tools JJ-8CS
All of them are important, but the most important information from the point of view of use of the device are in the user manual Jet Tools JJ-8CS.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Jet Tools JJ-8CS, service manual, brief instructions and user manuals Jet Tools JJ-8CS. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Jet Tools JJ-8CS.

Similar manuals

A complete manual for the device Jet Tools JJ-8CS, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Jet Tools JJ-8CS by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Jet Tools JJ-8CS.

A complete Jet Tools manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Jet Tools JJ-8CS - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Jet Tools JJ-8CS, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Jet Tools JJ-8CS, that we can find in the current document
3. Tips how to use the basic functions of the device Jet Tools JJ-8CS - which should help us in our first steps of using Jet Tools JJ-8CS
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Jet Tools JJ-8CS
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Jet Tools JJ-8CS in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Jet Tools JJ-8CS?

Use the form below

If you did not solve your problem by using a manual Jet Tools JJ-8CS, ask a question using the form below. If a user had a similar problem with Jet Tools JJ-8CS it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)