Manual Konica Minolta 181

362 pages 9.23 mb
Download

Go to site of 362

Summary
  • Konica Minolta 181 - page 1

    User’ s Guide [IC-206 Image Contr oller] ...

  • Konica Minolta 181 - page 2

    IC-206 x-1 Introduction Thank you for purchasing this machin e. This manual provides descriptions on the functions of the PCL printer driver and the use of network scanning and network pri nting functions used with the Internet or on an intranet. Be sure to read this manual be fore performing any operations. For precautions concerning the use and s ...

  • Konica Minolta 181 - page 3

    x-2 IC-206 person or organization contemplating ex port to obtain such a lice nse before exporting. WITHIN THAT CONSTRAINT, permission to use, copy, modify, and distrib- ute this software and its documentatio n for any purpose and without fee is hereby granted, provided that the above copyright notice appear in all copies and that both that copyrig ...

  • Konica Minolta 181 - page 4

    IC-206 x-3 the suitability of this software for an y purpose. It is provided “as is” without express or implied warranty. THIS SOFTWARE IS PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE OpenLDAP Public License The O ...

  • Konica Minolta 181 - page 5

    x-4 IC-206 Copyright 1999-2003 The OpenLDAP Foundation, Redwood City, C alifornia, USA. All Rights Reserved. Permission to copy and di stribute verbatim copies of this document is granted. Cyrus S ASL Copyright © 2001 Carnegie Mellon University. All righ ts reserved. Redistribution and use in source and bi nary forms, with or without modifica- tio ...

  • Konica Minolta 181 - page 6

    IC-206 x-5 this list of conditions and the f ollowi ng disclaimer in the documentation and/ or other materials provided with the distribution. Neither the name of Cal dera Systems nor the names of its contribu tors may be used to endorse or promote product s d erived from this software without specific prior written permission. THIS SOFTWARE IS PRO ...

  • Konica Minolta 181 - page 7

    x-6 IC-206 THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED WARRAN TIES, INCLUDING, BUT NOT LIM- ITED TO, THE IMPLIED W ARRANTIES OF MERCHANTABILITY AND FIT- NESS FOR A PARTICULAR PURPOSE AR E DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LI ABLE FOR ANY DIRECT, INDIRECT, INCIDENTA ...

  • Konica Minolta 181 - page 8

    IC-206 x-7 3. All advertising materials men tioning features or use of th is software must display the following acknowledgement: “This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)” The word ‘cryptographic ’ can be left out if the rouines from the library be - ing used are not cryptogra phic related :-). ...

  • Konica Minolta 181 - page 9

    x-8 IC-206 About PageScope We b Connection Network utility PageScope Web Connecti on can be used when a network in- terface card or image con troller is installed. PageScope Web Con nection is an extremely useful net work utility for specifying n etwork and other settings over the network. PageScope Web Connection can be used simply with the Web br ...

  • Konica Minolta 181 - page 10

    IC-206 x-9 Software End User License Agreement PLEASE READ CAREFULLY THE LI CENSE AG REEMENT BELOW BEFORE OPENING THE PACKAGE OF THIS SOFTWARE (“SOFTWARE”), DOWN- LOADING, INSTALLING OR USING THE SOFTWARE. OPENING THE PACK- AGE, OR DOWNLOADING, INSTAL LING OR USING THE SOFTWARE SHALL BE DEEMED YOUR LAWFUL ACCEPTANCE OF THE TERMS AND CONDITIONS ...

  • Konica Minolta 181 - page 11

    x-10 IC-206 (i) use, copy, modify, merge or tran sfer copies of the Software except as p ro- vided herein; (ii) reverse engine er, reverse assemble, reverse compile or any other way an- alyze the Software; or (iii) sublicense, rent, le ase or distribute the Software or any copy thereof. (iv) remove, use, or alter any trademar k, logo, copyright or ...

  • Konica Minolta 181 - page 12

    IC-206 x-11 6. GOVERNING LAW This Agreement shall be governed by the laws of Ja pan. 7. SEVERABILITY In the event th at any part or parts of this agreement shall be he ld illegal or null and void by any court or administra tive body of competent jurisdiction, such determination shall n ot effect the remaining parts of this agreement and they shall ...

  • Konica Minolta 181 - page 13

    x-12 IC-206 Contents Introduction About PageScope Web Connec tion ............... .............. ................ .. x-8 Copyright .............. .............. ................ .............. .............. ................ x-8 Software End User License A greement ............ ................. .............x-9 Contents ....... .............. .... ...

  • Konica Minolta 181 - page 14

    IC-206 x-13 2.5 Installing the printer driver by using the Add Pri nter Wizard ..... 2-15 Connecting to a computer thr ough a network .................. ........... 2-15 Installing using the Add Printer Wizard on Windows XP/ Server 2003 .................... .............. ................. .............. .............. ... 2-16 Installing using the ...

  • Konica Minolta 181 - page 15

    x-14 IC-206 4 Specifying printer driver settings 4.1 Printer drive r settings dialog box ............... .............. .............. ..........4-1 Displaying the settings dialog box ....................... .............. .............4-1 Printing Preferences dialog box ........ ..... .............. .............. .............4-3 Properties dialo ...

  • Konica Minolta 181 - page 16

    IC-206 x-15 5 Control panel operations for printing functions 5.1 Printing operations ......................... .............. .............. .............. ........ 5-1 Printer indicator ................. ................. .............. .............. ................ 5-1 Starting the print operat ion ..... .............. .............. ......... ...

  • Konica Minolta 181 - page 17

    x-16 IC-206 7.6 LDAP SETT ING .. .............. ................. .............. .............. .............. .....7-35 Specifying the LDAP server address ................... ................. ........7-35 Specifying the LDAP port number .................. ................ ..............7-37 Selecting the SSL setting .................... ......... ...

  • Konica Minolta 181 - page 18

    IC-206 x-17 9.4 Changin g the document scanni ng density ............... .............. ...... 9-23 When “TEXT/PHOTO” or “TEXT” was selected ................ ........... 9-23 When “PHOTO” was selected ................... .............. ................. ... 9-26 9.5 Specifyi ng the default scannin g settings ............... ............ ...

  • Konica Minolta 181 - page 19

    x-18 IC-206 11.7 User mode ..................... .............. .............. .............. .............. .........11-10 User mode tabs ....................... .............. .............. ................. ......11-10 System tab — Summary ..................... .............. ................. .........11-11 System tab — Details — Input T ...

  • Konica Minolta 181 - page 20

    IC-206 x-19 When “E-Mail” or “LDAP Sea rch” is selected: .......................... . 11-56 When “FTP Server Address” is select ed: ......... ........... ........... .... 11-57 Scan tab — Group Dial Se tting ........................ .............. ............ 11-58 Scan tab — Fax Configuration ............................ ......... ...

  • Konica Minolta 181 - page 21

    x-20 IC-206 Explanation of manual conventions ...

  • Konica Minolta 181 - page 22

    Getting ready 1 IC-206 1-1 1 Getting ready This chapter provides information that is im portant to know before this de- vice is used. 1.1 Overview By installing image controller IC-206, this machine ca n be used as a net- work-compatible PCL printer. In order to use the PCL printing functions, in- stall onto the computer the PCL printer drive r inc ...

  • Konica Minolta 181 - page 23

    1 Getting ready 1-2 IC-206 1.2 Names of control panel parts and their functio ns 1 2 3 4 6 7 8 9 21 20 19 5 10 18 11 12 13 14 15 16 17 No. Part name Descri ption 1 [Power Save] key Press to enter Power Save mode. 2 [Mixed Original] key/indicator Press to select the “Mixed Original” setting. 3 [Simplex/Duplex] key/indicator Press to selec t doub ...

  • Konica Minolta 181 - page 24

    Getting ready 1 IC-206 1-3 13 [Quality] key Press to select “TEXT”, “PHOTO” or “TEXT/ PHOTO” as th e document quality. 14 [Zoom] key P ress to specify wh eth er to enlarge or reduce the image when copying. 15 [Paper] ke y Press to select the pape r drawer that is to be used. 16 [Function] key/indicator Press to sp ecify settings for adv ...

  • Konica Minolta 181 - page 25

    1 Getting ready 1-4 IC-206 22 23 24 26 25 27 28 29 30 No. Part name Descri ption 22 [Fax] key/indicator Press to enter F ax mode. The in dicator on the key lights up in green to indicate th at the ma- chine is in Fax mode. 23 [Scan] key/indicator Press to e nter Scan m ode. The indic ator on the key lights up in green to indicate that the machine i ...

  • Konica Minolta 181 - page 26

    Getting ready 1 IC-206 1-5 28 [Clear/Stop] k ey • Press to clear the entere d number. • Press to stop a c ontinuous copy operation. • Press to st op the transmiss ion/reception of the fax. • Press to stop the print job from the compu- ter. 29 [Start] k ey/indicator • Press to s tart a copy operation. • Press to st art sending a fax . ? ...

  • Konica Minolta 181 - page 27

    1 Getting ready 1-6 IC-206 31 32 33 34 36 35 No. Part name Descri ption 31 Auto RX indicator This indicator lights up when the automatic re- ception function is selected. 32 [Memory TX] key/indicator Press this key to select the memory transmis- sion function. This indicator lights up in green when the memory transmission functio n is se- lected. 3 ...

  • Konica Minolta 181 - page 28

    Getting ready 1 IC-206 1-7 1.3 Entering text Follow the procedure described below to enter text when specifying the user name or programming one-touch di al keys with the recipient name. Changing the inpu t mode Each press of the [123/ABC] key swit ches between number input mode and letter input mode. [1…]: Numbers can be entered. [A…]: Letters ...

  • Konica Minolta 181 - page 29

    1 Getting ready 1-8 IC-206 Text input example To enter the name “Office 0 1”: Press the [123/ABC] key until in put mode [A…] is selected. * The cursor (_) flashes al ternately in the display with the character at its cur- rent location. 0 0 (space) 0 * + & / * = ! ? ( ) % [ ] ^ ‘ ’ { } | ~ $ , : ; < > “ ### Keypad key Availabl ...

  • Konica Minolta 181 - page 30

    Getting ready 1 IC-206 1-9 Press the [3] key 7 times . Press the [ ) ] key. Press the [3] key 7 times . Press the [4] key 7 times . Press the [2] key 7 times . ...

  • Konica Minolta 181 - page 31

    1 Getting ready 1-10 IC-206 Press the [3] key 6 time s. Press the [0] key. Press the [123/A BC] key. Press the [0] key. ...

  • Konica Minolta 181 - page 32

    Getting ready 1 IC-206 1-11 Correcting text and input precautions To delete a part of the entered text: Press the [ * ] or [ ) ] key to move the curs or (_) below the character to be de- leted, and then press the [Clear/Stop] key. To change entered characters: Press the [ * ] or [ ) ] key to move the cursor (_) bel ow the character that you wish to ...

  • Konica Minolta 181 - page 33

    1 Getting ready 1-12 IC-206 1.4 Connecting to a lo cal area network (LAN) This machine can transmit with the TCP/ IP protocol on a LAN. Therefore, this machine must be connected to the LAN with a network cable. Connecting the network cable Insert one plug on the network cable in to the network port (LAN) on the left side of the machine, and then in ...

  • Konica Minolta 181 - page 34

    Installing the printer driver 2 IC-206 2-1 2 Installing the printer driver Descriptions on connecting the mach ine to a computer and installing the printer driver are provided below. 2.1 System requirements The following environment is required so that the printer driver can be used. 2 Reminder The printer driver i s not compatible with Windows 95/ ...

  • Konica Minolta 181 - page 35

    2 Installing the printer driv er 2-2 IC-206 2.2 Making connections an d installing the driver Connecting to a computer This machine can be connecte d to a computer using any of the following connection methods. Connecting to a USB port In the following procedu re, the machine is connected dire ctly to the compu- ter by using a USB cable. When the m ...

  • Konica Minolta 181 - page 36

    Installing the printer driver 2 IC-206 2-3 Connecting to the netwo rk In the following procedu re, the machine is connected dire ctly to the compu- ter by using a network cable. When the machine is connec ted to a network, use the Add Printer Wiza rd to install the printer driver. For the procedu re on installing the printer driver when this machin ...

  • Konica Minolta 181 - page 37

    2 Installing the printer driv er 2-4 IC-206 2 Note When installing using Plu g and Play, the TWAIN driver for sc anning is also installed with the printer driver. For details on th e TWAIN driver, refer to the User’s Gu ide for the TWAIN driver. This machine cannot be connec ted to a computer running Windows 98 SE using a USB interface. Connectio ...

  • Konica Minolta 181 - page 38

    Installing the printer driver 2 IC-206 2-5 2.3 General operation fo r driver installation The driver is installed according to the following general operation. Installation using Plug and Play When installing the driver by using Plug and Play, the installation procedure differs depending on the operating system. With Windows Me With Windows XP, Win ...

  • Konica Minolta 181 - page 39

    2 Installing the printer driv er 2-6 IC-206 Installation using the Add Printer Wi zard When installing the printer driver by us ing the Add Printer Wizard, the instal- lation procedure is the sa me for all operating systems. With Windows 98 SE With Windows Me With Windows XP, Windows Server 2003, Win- dows Vista and Windows 2000 Install the printer ...

  • Konica Minolta 181 - page 40

    Installing the printer driver 2 IC-206 2-7 2.4 Installing the printer driv er by using Plug and Play Connecting to the co mputer’s US B port When this machine i s connected to a c omputer with a USB cable, Plug and Play detects the de vice, and then in stallation of the ne cessary drivers begi ns. 1 Start Windows, and then insert th e CD-ROM/DVD ...

  • Konica Minolta 181 - page 41

    2 Installing the printer driv er 2-8 IC-206 Installing using Plug and Play on Windows XP/Server 2003 2 Note If the driver is installed using Plug and Play, first the TWAIN driver for scanning is installed, and then instal lation of the printer driver begins. The procedure described in this manual is for the inst allation of the TWAIN driver, then t ...

  • Konica Minolta 181 - page 42

    Installing the printer driver 2 IC-206 2-9 2 Select “Include this location in the search:” and then specify the follow- ing folder on the CD-R OM as the location where the driver is saved. – Folder to be specified: DriverWIN2K_XPEnglish – With 64-bit operating syste ms, select “DriverWinXP 64English”. – The folder can be selected ...

  • Konica Minolta 181 - page 43

    2 Installing the printer driv er 2-10 IC-206 Installing using Pl ug and Play on Windows Vista 2 Note If the driver is installed using Plug and Play, first the TWAIN driver for scanning is installed, and then instal lation of the printer driver begins. The procedure described in this manual is for the inst allation of the TWAIN driver, then the prin ...

  • Konica Minolta 181 - page 44

    Installing the printer driver 2 IC-206 2-11 5 Select “Include subfolde rs”, and then specify the following folder on the CD-ROM as the location wher e the driver is saved. – Folder to be specified: DriverWinVistaEnglish – With 64-bit operating systems, sele ct “DriverWinVista64English”. – The folder can be selected after cli cki ...

  • Konica Minolta 181 - page 45

    2 Installing the printer driv er 2-12 IC-206 Installing using Plug an d Play on Windows 2000 2 Note If the driver is installed using Plug and Play, first the TWAIN driver for scanning is installed, and then instal lation of the printer driver begins. The procedure described in this manual is for the inst allation of the TWAIN driver, then the print ...

  • Konica Minolta 181 - page 46

    Installing the printer driver 2 IC-206 2-13 Installing using Pl ug and Play on Wi ndows Me 2 Note If the driver is installed using Plug and Play, firs t the TWAIN driver for scanning is installed, ne xt the USB printing support driver is installed, and then installation of the printer drive r begins. The procedure described in this manual is for th ...

  • Konica Minolta 181 - page 47

    2 Installing the printer driv er 2-14 IC-206 8 Click the [Finish] button. – To change the p rinter name, type in the new nam e. – To set this machine as the default, se lect “Yes”. A dialog box appears, in dicating that the ins tallation is finished. 9 Click the [Finish] button. This completes the installation of the printer driver. Reinsta ...

  • Konica Minolta 181 - page 48

    Installing the printer driver 2 IC-206 2-15 2.5 Installing the printer driv er by using the Add Printer Wizard Connecting to a comput er through a network If this machine is connec ted to a computer through a network, the printer driver can be installed either before or after the connection is establi shed. % Use the network cable to connect this m ...

  • Konica Minolta 181 - page 49

    2 Installing the printer driv er 2-16 IC-206 Installing using t he Add Printer Wizard on Windows XP/Serv er 2003 2 Note When using a USB cable to connect this machine to the computer, turn off this machine, and then install the printer dri ver. When the machi ne is turned on, Plug a nd Play causes the Add New Hardware Wizard to ap- pear. 1 After Wi ...

  • Konica Minolta 181 - page 50

    Installing the printer driver 2 IC-206 2-17 – If “Printer Tasks” does not appea r, double-click the “Add Printer” icon. The Add Printer Wizard starts up. 4 Click the [Next] button. 5 Select “Local printe r attached to thi s computer”, and t hen click th e [Next] button. – The “Automatic ally detect and i n stall my Plug and Play p ...

  • Konica Minolta 181 - page 51

    2 Installing the printer driv er 2-18 IC-206 8 Click the [Browse] button, select “DriverWIN2K_XPEnglish” on the CD-ROM, and then click the [Open] button. – With 64-bit operating systems, select “DriverWinXP64English”. 9 Click the [Open] button again. 10 Check the path in t he “Copy manufacturer’s file s from” box, and then click ...

  • Konica Minolta 181 - page 52

    Installing the printer driver 2 IC-206 2-19 11 Select the printer to be installed, and then click the [Next] button. 12 Continue selecting the appropriate se ttings according to your environ- ment and clicking the [Next] butto n un til the [Finish] button appears. – For a network connection, perform a test print afte r specifying the network sett ...

  • Konica Minolta 181 - page 53

    2 Installing the printer driv er 2-20 IC-206 Installing using t he Add Printer Wizard on Windows Vista 2 Note When using a USB cable to connect this machine to the computer, turn off this machine, and then install the printer dri ver. When the machi ne is turned on, Plug and Pla y causes the Found New Hardwar e wizard to ap- pear. 1 After Windows h ...

  • Konica Minolta 181 - page 54

    Installing the printer driver 2 IC-206 2-21 – In order to print on a network, th e connection port must be set up as a network port. Since the port settings can be specified after in- stallation, this procedure describe s how to install the printer driver for a local connection. For det ails on specifying the port settings, refer to “Connecting ...

  • Konica Minolta 181 - page 55

    2 Installing the printer driv er 2-22 IC-206 11 Select the printer to be installed, and then click the [Next] button. 12 Continue selecting the appropriate settings according to your environ- ment and clicking the [Next] button un til the [Finish] button appears. – If the User Accoun t Control dialog box appears, c lick the [Continue] button. – ...

  • Konica Minolta 181 - page 56

    Installing the printer driver 2 IC-206 2-23 Installing using the Add Prin ter Wizard on Windows 2000 2 Note When using a USB cable to connect this machine to the computer, turn off this machine, and then install the printer driver. When the machine is turned on, Plu g and Play causes the Add New Hardware Wizard to ap- pear. 1 After Windows has star ...

  • Konica Minolta 181 - page 57

    2 Installing the printer driv er 2-24 IC-206 6 Select “LPT1:” beside “Use the following port ”, and then click the [Next] but ton. 7 Click the [Have Disk] button. 8 Click the [Browse] button, select “DriverWIN2K_XPEnglish” on the CD-ROM, and then click the [Open] button. 9 Click the [Open] button again. 10 Check the path in t he “Co ...

  • Konica Minolta 181 - page 58

    Installing the printer driver 2 IC-206 2-25 11 Select the printer to be installed, and then click the [Next] button. 12 Continue selecting the appropriate se ttings according to your environ- ment and clicking the [Next] butto n un til the [Finish] button appears. – For a network connection, perform a test print afte r specifying the network sett ...

  • Konica Minolta 181 - page 59

    2 Installing the printer driv er 2-26 IC-206 Installing using t he Add Printer Wizard on Windows Me/98 SE 2 Note When using a USB cable to connect this machine to the computer, turn off this machine, and then install the printer dri ver. When the machi ne is turned on, Plug a nd Play causes the Add New Hardware Wizard to ap- pear. This machine cann ...

  • Konica Minolta 181 - page 60

    Installing the printer driver 2 IC-206 2-27 6 Click the [Have Disk] button. 7 Click the [Browse] button, select “DriverWin98_MEEnglish” on the CD-ROM, and then click the [OK] button. 8 Click the [OK] button again. 9 Check the path in t he “Copy manufacturer’s fi les from” box, and then click the [OK] button. 10 Select the printer to be ...

  • Konica Minolta 181 - page 61

    2 Installing the printer driv er 2-28 IC-206 13 After installation is comple te, check that the icon for the installed print- er appears in the Printers window, and then remove the CD-ROM from the CD-ROM drive. This completes the installation of the printer driver. Reinstalling the p rinter driver by using the A dd Printer Wizard 1 Uninstall the pr ...

  • Konica Minolta 181 - page 62

    Installing the printer driver 2 IC-206 2-29 2.6 Uninstalling the printer driver 2 Note With Windows XP, Server 2003, Vista and 2000, log on as a user with Ad- ministrator privileges to delete the printer driver . For details on deleting the TWAIN drive r, refer to the User’s Guide for the TWAIN driver. Delete the printer 1 Open the Printers and F ...

  • Konica Minolta 181 - page 63

    2 Installing the printer driv er 2-30 IC-206 – If Windows 2000, XP or Server 2003 is being used, continu e with step 7. – If Windows Vista is be ing used, continue with step 6. 6 When a message appears, requesting confirmati on to contin ue delet- ing, select “Remove driver and drive r package.”, an d then click the [OK] button. 7 When a me ...

  • Konica Minolta 181 - page 64

    Installing the printer driver 2 IC-206 2-31 Deleting related files Even after the printer driver is delete d from the Printers and Faxes window, device information files remain on the computer. When using Windows XP/Server 2003, it may not be possible to overwrite the driver, even if the same version of th e printer driv er is reinstalled. If the p ...

  • Konica Minolta 181 - page 65

    2 Installing the printer driv er 2-32 IC-206 ...

  • Konica Minolta 181 - page 66

    Network printing 3 IC-206 3-1 3 Network printing This chapter provides desc riptions of the procedures for installing the image controller and usin g this mach ine as a network printer. 3.1 Selecting the netw ork printing method When the image controller is installed, various network printing methods are possible. The following procedure desc ri be ...

  • Konica Minolta 181 - page 67

    3 Network pri nting 3-2 IC-206 LPR printing / PORT9100 printing Compatible operating systems: Wind ows 2000 / Windows XP / Windows Sever 2003/Windows Vista LPR printing - Using the LPR (line printer remote) pr int service, the computer and this machine are connected over a network. - The LPR print service is supported by the operating system as the ...

  • Konica Minolta 181 - page 68

    Network printing 3 IC-206 3-3 IPP printing Compatible operating systems: Wind ows 2000 / Windows XP / Windows Sever 2003/Windows Vista IPP printing - Using the IPP (Internet printing proto col) print service, the computer and this machine are connecte d over a network. - The IPP print service is supported by the operating system as the stand- ard. ...

  • Konica Minolta 181 - page 69

    3 Network pri nting 3-4 IC-206 When using a NetWare environment (NetWare server and Windows cli- ent) In a NetWare environment, the Windows computer is used as a NetWar e cli- ent, and print ing with this machin e is possible through th e NetWare server. Connecting the NetWare server and this machine When connecting the NetWare server an d this mac ...

  • Konica Minolta 181 - page 70

    Network printing 3 IC-206 3-5 3.2 Checking the setup This section provides an overview of th e setup procedure that is required for each network printing method. Peer-to-peer printing 1 Connect the network ca ble. (Refer to “Connecting to a local area net- work (LAN)” on page 1-12.) 2 From the machine’s control panel, sp ecify the IP addre ss ...

  • Konica Minolta 181 - page 71

    3 Network pri nting 3-6 IC-206 LPR/PORT9100 printing 1 Connect the network cable. (Refer to “Connect ing to a local area net- work (LAN)” on page 1-12.) 2 From the machine’s control panel, s p ecify the IP addre ss, subnet mask and default gateway. (Ref er to “Specifying an IP address” on page 3-9.) 3 Print the settings information, and t ...

  • Konica Minolta 181 - page 72

    Network printing 3 IC-206 3-7 IPP printing 1 Connect the network ca ble. (Refer to “Connecting to a local area net- work (LAN)” on page 1-12.) 2 From the machine’s control panel, sp ecify the IP addre ss, subnet mask and default gateway. (Refer to “Spe cifying an IP address” on page 3-9.) 3 Print the settings information, and t hen check ...

  • Konica Minolta 181 - page 73

    3 Network pri nting 3-8 IC-206 NetWare server/client (except NDPS) 1 Connect the network cable. (Refer to “Connect ing to a local area net- work (LAN)” on page 1-12.) 2 Specify the necessary settin gs for connecting this machine to a Ne t- Ware server. (Refer to “Connecting the computer and this mach ine over a network” on page 3-15.) 3 Spe ...

  • Konica Minolta 181 - page 74

    Network printing 3 IC-206 3-9 3.3 Specifying an IP address The following procedure de scribes how to assign the IP address to the m a- chine from the control panel. 2 Note The IP address setting should be specif ied according to instructions from the network administrator. The IP address setting is specified in Utility mode by the administrator. 1 ...

  • Konica Minolta 181 - page 75

    3 Network pri nting 3-10 IC-206 3 Type in the administrator acc ess code, and then press the [OK] key. – The manufactur er’s default se tting is “000000 ”. – If the code was incorrectly entere d, press the [Clear/Stop] key to erase the number, and then type it in corr ectly. 4 Press the [ , ] or [ + ] key until “NETWORK SE TTING” is s ...

  • Konica Minolta 181 - page 76

    Network printing 3 IC-206 3-11 6 Press the [ , ] or [ + ] key until “AUTO” or “SPECIFY” is selected, and then press the [OK] key. – If “AUTO” was selected , the IP address will automatically be ob- tained from the DHCP server. A fter the message “ACCEPTED” ap- pears, the “NETWORK SETTING” menu appears again. – If “SPECIFY? ...

  • Konica Minolta 181 - page 77

    3 Network pri nting 3-12 IC-206 9 Using the keypad, type in the gateway. – For the gateway, consult with the network administrator. – If the number was incorrectly entere d, press the [Clear/Stop] key to erase it, and then type it in correctly. 10 Press the [OK] key. The message “ACCEPTED” appears, and then the “NETWORK SET- TING” menu ...

  • Konica Minolta 181 - page 78

    Network printing 3 IC-206 3-13 3.4 Printing the sett ings information Print the settings information to be able to check the settings. 1 From the control panel, press the [Confir m] key. The “CONFIRM MODE” menu appears. 2 Press the [ , ] or [ + ] key until “PRINT REPO RT” is selected, an d then press the [OK] key. The “PRINT REPORT” men ...

  • Konica Minolta 181 - page 79

    3 Network pri nting 3-14 IC-206 4 Press the [OK] key. After the message “PRINTING” appe ars, the settings informati on is printed. 2 Note If “PCL FONT LI ST” is selected, the list of printer fonts can be viewed. ...

  • Konica Minolta 181 - page 80

    Network printing 3 IC-206 3-15 3.5 Connecting the computer and this machine over a network Specify the settings necessary for con necting the computer and this ma- chine over the n etwork and sending a print job t hrough the network from the computer. The following conne ction procedures a re described in this section. - Peer-to-peer printing – W ...

  • Konica Minolta 181 - page 81

    3 Network pri nting 3-16 IC-206 4 Click the Details tab, and then click the [Add Port] button. 5 Select “Other”, and then select “Pee r2Peer” from the “list of port types”. 6 Click the [OK] button. 7 Type in the IP addre ss of this mach ine, and then click the [OK] button. 8 Click the [Apply] or the [OK] button. LPR pr intin g Compatibl ...

  • Konica Minolta 181 - page 82

    Network printing 3 IC-206 3-17 8 Select “Custom”, and then c lick the [Settings] button. 9 Select “LPR” in the protocol group box, type the queue na me in the “Queue Name” box of the “LPR Setti ng s” group box, and then click the [OK] button. – Type in a queue name that be gins with a letter (for e xample, “print”). 10 Click t ...

  • Konica Minolta 181 - page 83

    3 Network pri nting 3-18 IC-206 3 Click “Properties” to open the Properties dialog box. 4 Click the Ports tab, and then click the [Add Port] button. 5 In the Printer Ports dialog box, select “Standard TCP/IP Port”, and then click the [New Port] button. 6 After the Add Standard TCP/IP Printe r Port Wizard starts up, click the [Next] but ton. ...

  • Konica Minolta 181 - page 84

    Network printing 3 IC-206 3-19 2 Reminder Before specifying settings, ch eck that the following preparations have been completed. The computer can communica te using the TCP/IP protocol. This machine can commun icate using the TCP/IP protocol. The printer driver is installed on the compute r. (For details on installing t he PCL drive r, refer to ? ...

  • Konica Minolta 181 - page 85

    3 Network pri nting 3-20 IC-206 IPP printing connections Establish the IPP printing connection. The IPP printing con nection must be set up starting from the installation of the printer driver. (For detai ls on install- ing the PCL driver, refer to “Installing th e printer driver by us ing the Add Pr int- er Wizard” on page 2-15. If the GDI dri ...

  • Konica Minolta 181 - page 86

    Network printing 3 IC-206 3-21 Connecting the IPP printing NetW are server and this machine Connecting the NetWare server and this machine Specifying the NetWar e 4.x/5.x/ 6 print server mod e settings 1 Log on with Administrator privileges. 2 Start up NWadmin. 3 Select the print server system or ca tegory container, and then select “Print servic ...

  • Konica Minolta 181 - page 87

    3 Network pri nting 3-22 IC-206 After changing the settings for parameters marked with an asterisk (*), turn the machine off , then on again. Specifying the NetWare 4.x/5. x/6 remote printer mode setting s 1 Log on with Administrator privileges. 2 Start up NWadmin. 3 Select the organization performing the print service or the category container, an ...

  • Konica Minolta 181 - page 88

    Network printing 3 IC-206 3-23 After changing the settings for parameters marked with an asterisk (*), turn this machine off, then on agai n. Specifying the NetWare 5.x/6 Novell Distributed Print Service (NDPS) settings 2 Reminder Before specifying NDS settings, make sure that NDPS Broker and NDPS Manager have been created and loaded. Check that th ...

  • Konica Minolta 181 - page 89

    3 Network pri nting 3-24 IC-206 Creating an NDPS printer agent 1 Log on with Administrator privileges. 2 Start up NWadmin. 3 Right-click the name of the organization or department container where you want to create the pri nter agent, and then select “NDPS printer”. 4 In the “NDPS Printer Name” bo x, type the printer name. 5 In the “Print ...

  • Konica Minolta 181 - page 90

    Specifying printer driver settings 4 IC-206 4-1 4 Specifying printer driver settings Descriptions on the prin ter driver settings availabl e when printing from a computer are provided below. 4.1 Printer driver settings dialog box Displaying the setting s dialog box Select the printer in the Printers and Faxes window (the Printers window in Windows ...

  • Konica Minolta 181 - page 91

    4 Specifying printer driver settings 4-2 IC-206 The following printer driver settings dialog box appears. 2 Note To change the settings for each job to be printed, click the [Properties] button (or the [Preferences] button) in the Print dialog box, which appears when “Print” is clicked in the application. Th e settings specified in the di- alog ...

  • Konica Minolta 181 - page 92

    Specifying printer driver settings 4 IC-206 4-3 Printing Preferences dialog box Printing settings can be specifie d from the printer driver setti ngs dialog box. 2 Note To display the Printing Preference s dialog box in Windows XP/Server 2003/Vista/2000, right-clic k the icon for the installe d printer in the Print- ers and Faxes window (or the Pri ...

  • Konica Minolta 181 - page 93

    4 Specifying printer driver settings 4-4 IC-206 Tab Item Description Setup Orientation Select the paper orient ation of the document. Original Size Specify the paper size for the docu ment. [Edit Custom] button Specify a user- defined paper size. Output Size Specify the size of paper to be printed on. If this size is differ ent from the original do ...

  • Konica Minolta 181 - page 94

    Specifying printer driver settings 4 IC-206 4-5 Quality Resolution Specify the print resolution. [Adjustment] button Specify th e bri ghtness and contrast. [Font Settings] button Select whether Tr ueType fonts or printer fonts are used during printing. Toner Save Select whether or not to print while controlling toner consumption. About - Shows the ...

  • Konica Minolta 181 - page 95

    4 Specifying printer driver settings 4-6 IC-206 Properties dialog box Installed options can be se lected from the Properties dialog box for the print- er driver. 2 Reminder If the options installed on the machine are not specified from the Device Options tab, the functions available wi th the option cannot be used from the printer driver. Be sure t ...

  • Konica Minolta 181 - page 96

    Specifying printer driver settings 4 IC-206 4-7 4.2 Devic e Options t ab Specify whether or not options are instal led so that the options installed on the machine can be used from the pr inter driver. 2 Reminder If the options instal led on the machin e are not specified from the Device Options tab, the functions availa ble with the option cannot ...

  • Konica Minolta 181 - page 97

    4 Specifying printer driver settings 4-8 IC-206 Device Options Specify the settings for th e installed pa per drawers. From the “Device Options” list, doub le-click the names of installed paper drawers to specify that it is installed. Double-click the name again to return the setting to “Not Installed”. Memory Specify the size of the instal ...

  • Konica Minolta 181 - page 98

    Specifying printer driver settings 4 IC-206 4-9 4.3 Common operations This section contains descriptions of button s and functions common to all tabs of the dialog box. The actual butto ns may appear differently depending on the operating system. Common items Button Descri ption [OK] button Click this button to apply the specified settings and clos ...

  • Konica Minolta 181 - page 99

    4 Specifying printer driver settings 4-10 IC-206 Easy Set The currently specified setti ngs can be registered as a program to be re- called later when you wish to use those sett ings again. 1 Change the driver settings on the Setup and Layout tabs. 2 In the “Easy Set” box, type the name of the program. 3 Click the [Save] button. The settings pr ...

  • Konica Minolta 181 - page 100

    Specifying printer driver settings 4 IC-206 4-11 2 Note To recall a registered program, select it from the list. To change the name of the registe red program, select the program from the list, and then type in the new program name. The button changes to the [Rename] button. To change the program name, click the [Rename] button. To delete a registe ...

  • Konica Minolta 181 - page 101

    4 Specifying printer driver settings 4-12 IC-206 4.4 Setup tab From the Setup tab, settings can be specified for the document and paper to be printed on. The number of copies to be printed and the orientation of the printed image can also be specified. Orientation Select whether to print the document in the portrait or landscape orientation. ABCD A ...

  • Konica Minolta 181 - page 102

    Specifying printer driver settings 4 IC-206 4-13 Original Size From the drop-down list, click the paper size for the document to select it. The following standard pa per sizes are available. 2 Note If “Hagaki” is selected, sele ct the “Hagaki” pape r setting for Tray 1 from the control panel of the machine. “Hagaki” and the envelope a n ...

  • Konica Minolta 181 - page 103

    4 Specifying printer driver settings 4-14 IC-206 Edit Custom A paper size that does not appea r in the list can be registered as a custom size. 1 Click the [Edit Custom] button on the Setup tab. The Custom Size Settings dialog box appears. 2 Click the [New] button. The Custom Size Settings dialog box enlarges to display settings for specifying the ...

  • Konica Minolta 181 - page 104

    Specifying printer driver settings 4 IC-206 4-15 4 In the “Dimensions” group box, spec ify the width and length of the pa- per. – To change the uni ts for specifying the paper size, select the desired setting in the “Unit” group box. 5 Click the [OK] button in the lower-right corner of the Custom Size Set- tings dialog box. The paper size ...

  • Konica Minolta 181 - page 105

    4 Specifying printer driver settings 4-16 IC-206 Output Size Select the size of paper that is to be used for printing. The available standard paper sizes are sa me as those availa ble in the “Orig- inal Size” list. If the paper size is differen t from the size selected in the Original Size list, the document image will be printed enlarged or re ...

  • Konica Minolta 181 - page 106

    Specifying printer driver settings 4 IC-206 4-17 Zoom Specify the enla rgement or reductio n ratio to be used for printing. Select “Manual”, and then type in a number between 25% and 400%, or click the arrows to specify a setting. 2 Note If any setting other than “Same as Origin al Size” is selected in the “Output Size” list, “Manual? ...

  • Konica Minolta 181 - page 107

    4 Specifying printer driver settings 4-18 IC-206 Collate When printing multiple copies of t he same document, select whether the en- tire document is printed one copy at a time or whether the specified number of copies are p rinted one page at a time. When the “Collate” check box is selecte d, the entire document is pri nted one copy at a time. ...

  • Konica Minolta 181 - page 108

    Specifying printer driver settings 4 IC-206 4-19 Paper Source Select the paper drawer loaded with the paper. If “Auto” is selected, the paper drawer lo aded with paper of the size specified in the “Output Size” list is used. The available settings di ffer depending on the opti ons that are installed. Settings: Tray 1, Tray 2 through Tray 5 ...

  • Konica Minolta 181 - page 109

    4 Specifying printer driver settings 4-20 IC-206 Output Method Select the printing method. Not only can data be printed directly, but “Secure Print” is also available, which requires a password for printing from this ma chine. Settings: Print, Secure Print 2 Note “Secure Print” is available only if th e optional expanded memory unit is inst ...

  • Konica Minolta 181 - page 110

    Specifying printer driver settings 4 IC-206 4-21 Specifying secure printing from the printer driver 1 Click the Setup tab. 2 From the “Output Method” drop-down list, sele ct “Secure Print”. A screen appears, allowing you to type in the password. 3 Type in the password, and then click the [OK] button. – Specify the 4-digit password between ...

  • Konica Minolta 181 - page 111

    4 Specifying printer driver settings 4-22 IC-206 2 Check that the key icon appears in th e upper-right corner of the screen. – The key icon appears if the memo ry contains a secure print docu- ment. 3 Press the [Access] key. 4 When “PASSWORD: – – – –” appe ars, type in the password. – Type in the same numbers spec ified as the passw ...

  • Konica Minolta 181 - page 112

    Specifying printer driver settings 4 IC-206 4-23 5 Check that the docume nt can be printed. If the password is correct, the followi ng screen appears, and the job is printed. 2 Note If there are multiple secu re print jobs with the same password, all of those secure print jobs are printed. ...

  • Konica Minolta 181 - page 113

    4 Specifying printer driver settings 4-24 IC-206 4.5 Layout tab From the Layout tab, select the number of document pages to be printed on a single sheet of paper. ...

  • Konica Minolta 181 - page 114

    Specifying printer driver settings 4 IC-206 4-25 Combination Multiple document pages can be printed together on a single sheet of paper. Use combined printing to economize on the number of printed pages. From the drop-down list, se lect the number of pages to be printed on a single sheet of paper. For example, if “2 in 1” is selected, tw o page ...

  • Konica Minolta 181 - page 115

    4 Specifying printer driver settings 4-26 IC-206 Combination Details Click the [Combination Details] butto n to specify the printing order and whether or not to print page outlines. Combination Select the number of pages to be printed on a single sheet of paper. This is the same setti ng selected in the “Combination” li st on the Layout tab. Or ...

  • Konica Minolta 181 - page 116

    Specifying printer driver settings 4 IC-206 4-27 Double-sided printing Document pages can be printed on both sides of the paper. Print on both sides when binding a multi-page document. 1 Click the Layout tab. 2 From the “Double Sides” drop-down list, select “Double Sided”. 2 Note From the “Binding Position” drop-down list, select th e d ...

  • Konica Minolta 181 - page 117

    4 Specifying printer driver settings 4-28 IC-206 4.6 Per Page Setting tab From the Per Page Setting tab, specify whether or not a cover page is added. Front Cover Page/Back Cover Page Select whether or not a cover page is added and whether or not a document page is printed on the cover page. Settings: Front Cover Paper Source/Back Cover Paper Sourc ...

  • Konica Minolta 181 - page 118

    Specifying printer driver settings 4 IC-206 4-29 4.7 Watermark tab From the Watermark tab, sp ecific te xt can be printed in the background as a watermark. Watermark Select From the Watermark Select list, select the text. A setting is availa ble for specifying whethe r the watermark is printed on all pages or only on th e first page. Settings: (No ...

  • Konica Minolta 181 - page 119

    4 Specifying printer driver settings 4-30 IC-206 Creating a new watermark A new watermark can be registered. 1 Click the Watermark tab. 2 Click the [New] button. The New dialog box appears. 3 In the “Watermar k Text” box, type in the text to be used as the water- mark. – A maximu m of 20 chara cters can be entered for the text. – A maximum ...

  • Konica Minolta 181 - page 120

    Specifying printer driver settings 4 IC-206 4-31 – Offset from Center: Specify the horizontal and vertical positions for the location where the text is t o be printed. Settings between -10 0 and 100 can be specified. – The position can also be ch anged by using the sliders below and to the right of the preview image. 5 Click the [Add] button. T ...

  • Konica Minolta 181 - page 121

    4 Specifying printer driver settings 4-32 IC-206 Editing a watermark A registered watermark can be edited to change the text, size and position. 1 Click the Watermark tab. 2 From the list, select the watermark to be edited. 3 Click the [Edit] button. The Edit dialog box appears. 4 Specify the desired settings. – Watermark Text: Type in the waterm ...

  • Konica Minolta 181 - page 122

    Specifying printer driver settings 4 IC-206 4-33 – The position can also be ch anged by using the sliders below and to the right of the preview image. 5 Click the [OK] button. The watermark is cha nged. 2 Note To delete a registered watermark, sele ct the watermark fr om the list, an d then click the [Delete] button. Horizontal directi on: Reduci ...

  • Konica Minolta 181 - page 123

    4 Specifying printer driver settings 4-34 IC-206 4.8 Quality tab From the Quality tab, settings for the print quality can be specified. Resolution From the drop-down list, sp ecify the print resolution. ...

  • Konica Minolta 181 - page 124

    Specifying printer driver settings 4 IC-206 4-35 Adjustme nt Click the [Adjustment ] button to sp ecify the brightness and contrast. Brightness Adjust th e brightness of the printed image. A settin g between -50 and 50 can be specified. The larger t he number, th e higher the c ontrast and t he more distinct the image. Contrast Adjust the contrast ...

  • Konica Minolta 181 - page 125

    4 Specifying printer driver settings 4-36 IC-206 Font Set tings Settings can be spec ified to replace the TrueType fonts use d in Windows with the printer fonts installed on this machi ne. Font Set tings 1 Click the Quality tab. 2 Click the [Font Settings] button. 3 Specify the desired settings. – Use Printer Fonts: Select this setting to re plac ...

  • Konica Minolta 181 - page 126

    Specifying printer driver settings 4 IC-206 4-37 Specifying the Font Substitutions table 1 Click the [New] button. – To make changes, select the row con taining the font to be changed, and then cl ick the [Edit] button. 2 Select the TrueType font to be replac ed at the top, a nd then select the printer font to be used at the bottom. – While mak ...

  • Konica Minolta 181 - page 127

    4 Specifying printer driver settings 4-38 IC-206 2 Note To delete specified replace ments, select the row for the font, and then click the [Delete] button. Toner Save Select whether or n ot to print while controlling ton er consumption. This can be used when printing test pages. ...

  • Konica Minolta 181 - page 128

    Control panel operations for printing function s 5 IC-206 5-1 5 Control panel operations for printing functions Descriptions on the printing operations that can be performed from the con- trol panel of the machine are provided below. 5.1 Printing operations The default mode of the ma chine is the Copy mode. Normally, when printing is performed from ...

  • Konica Minolta 181 - page 129

    5 Control panel operations for printing funct ions 5-2 IC-206 Starting the print operation Normally, printing begins when printin g is performed from a connected com- puter. - Normally, when printing is performe d from a connected computer, print- ing begins automatically. - If a print operation is performed fr om a connected compute r while the ma ...

  • Konica Minolta 181 - page 130

    Control panel operations for printing function s 5 IC-206 5-3 Canceling a print jo b Printing of a print job can be cancel ed from the control panel of the ma- chine’s control pan el. Howe ver, a print job can only be canc eled from the control panel while the mach ine is in Printer mode. 1 Check that the Printer indicator is flashing or is lit , ...

  • Konica Minolta 181 - page 131

    5 Control panel operations for printing funct ions 5-4 IC-206 4 Press the [ + ]or [ , ] key to select “YES”, and then press the [OK] key. – To continue printing, select “No”. – If no key is pressed within five seconds, printing continues. “ACCEPTED” appears in the display and the print job is can celed. ...

  • Konica Minolta 181 - page 132

    Control panel operations for printing function s 5 IC-206 5-5 2 Note If any of the following messages appear in the display, the print job can also be canceled by repeating st eps 2 and 3 from the procedure de- scribed above. PAPER EMPTY PAPER JAM PAPER SIZE ERROR RESET PAPER NO SUITABLE PAPER UPPER TRAY FULL REMOVE PAPER IN BYPASS TRAY LOAD PAPER ...

  • Konica Minolta 181 - page 133

    5 Control panel operations for printing funct ions 5-6 IC-206 Using the manual bypass tray Follow the procedure described below wh en using the manual bypass tray to print one page at a time. 1 From the compute r, display the Setu p tab for the printer d river, and then select “Bypa ss” in the “Paper Sourc e” list (page 4-19) . 2 Perform th ...

  • Konica Minolta 181 - page 134

    Control panel operations for printing function s 5 IC-206 5-7 – Slide the paper guides to fit the size of paper being load- ed. 4 Repeat step 3 as often as necessa ry until printing of the document is finished. 2 Note Be sure to load the paper into the manual bypass tray after the print op- eration is performed from the compu ter. Follow the proc ...

  • Konica Minolta 181 - page 135

    5 Control panel operations for printing funct ions 5-8 IC-206 Power Save mode If print data is received while the ma chine is in Power Save mode, the mode is canceled. When print data is received, the data is printed after the machine has finished warming up. ...

  • Konica Minolta 181 - page 136

    Network scanning 6 IC-206 6-1 6 Network scanning Using the network scanni ng function, scan data can be se nt to a recipient ’s computer by e-ma il or it can be upload ed to an FTP ser ver. The scan data can be sent using any of the following methods. Choose the appropriate method acco rding on the network environment and purpose. 2 Note To use t ...

  • Konica Minolta 181 - page 137

    6 Network scanning 6-2 IC-206 Scan to E-mail 2 Note A network environ ment that include s a mail server is required. Scan data is attached to an e-mail message as a TIFF or PDF file, then sent to a computer on the network or to a computer through the Internet. Mail server Client computer Intranet Internet Mail server Client computer ...

  • Konica Minolta 181 - page 138

    Network scanning 6 IC-206 6-3 Scan to Server (FTP) Scan data can be uploaded as TIFF or PDF files to a spec ified directory on an FTP server. 2 Note A network environment that includes an FTP server is required. An FTP server on the Internet can be accesse d through a proxy server. FTP server Intranet Internet FTP server ...

  • Konica Minolta 181 - page 139

    6 Network scanning 6-4 IC-206 The system can be set to send to a specified reci pient (up to 10) a notifi cation of the location on the FTP server where the data was uploaded. Environments for network scan transmissions The following environment is required in order to use the net work scanning features. FTP server FTP server Internet Client comput ...

  • Konica Minolta 181 - page 140

    Network settings 7 IC-206 7-1 7 Network settings This chapter provides descriptions on specifying network settings from the control panel of th e machine. 7.1 Network sett ings The available network operati ons are limited according to the con nected LAN environment. Specify the network settings according to the environ- ment and functi ons to be u ...

  • Konica Minolta 181 - page 141

    7 Network settings 7-2 IC-206 DNS SET- TING Select whether or not DNS (Domain Name System) is used. If a DNS server is on the network, specify the IP address of the DNS server. If a DNS server is on the network, select “ENABLE”. Consult with the net- work a dmini strator . ●● oo GATEWAY TX *4 To send faxes direct- ly, select “ENABLE”. - ...

  • Konica Minolta 181 - page 142

    Network settings 7 IC-206 7-3 SMTP POR T NO. Specify the port number (betwe en 1 and 65535) of the SMTP server. Consult with the ne t- work administrator. o ● *1 oo SMTP TIME- OUT Specify the amount of time (bet ween 30 and 300 seco nds) until the connection with the SMTP server times out. Consult with the ne t- work administrator. o ● *1 oo TE ...

  • Konica Minolta 181 - page 143

    7 Network settings 7-4 IC-206 E-MAIL SETTIN G 2 POP3 SERV - ER AD- DRESS Specify the IP ad- dress or host na me for the POP3 server . Consult with the net- work a dmini strator . ● *6 ● *7 oo POP3 PORT NO. Specify the p ort number (between 1 and 65535) of the POP3 server. Consult with the net- work a dmini strator . ● *6 ● *7 oo POP3 TIME- ...

  • Konica Minolta 181 - page 144

    Network settings 7 IC-206 7-5 *1: Necessary if notification of th e URL is to be sent by e-mail. *2: Can also be obtained automa tically from the DHCP server. *3: Set the IP address to “0.0.0.0” if th ere is no usable SMTP server on the network. *4: The setting must be specified in orde r to use direct faxing. For details on direct faxing, refe ...

  • Konica Minolta 181 - page 145

    7 Network settings 7-6 IC-206 SEARCH METHOD Specify the met hod used to search for destination names. oo LDAP TIMEOUT Specify the amount of time (between 5 and 300 seconds) until a search times out. oo MAX. SEARCH RE- SULTS Specify t he maximum numb er of items (between 5 and 100) that can be re- ceived as LDAP search res ults. oo AUTHENTICATION Se ...

  • Konica Minolta 181 - page 146

    Network settings 7 IC-206 7-7 7.2 Specifying settings from the control panel The network settings can be specified from the control panel of this mach ine. To specify the network settin gs from the control panel of t he machine, press the [Utility] key, and then specify se ttings for the variou s menu parameters available from the “ADMIN. MANAGEM ...

  • Konica Minolta 181 - page 147

    7 Network settings 7-8 IC-206 *1 : These items can be displayed only IP ADDRESS SETTING is set to “SPECIFY”. *2 : Can be specified if network interfa ce card NC-503 or image controll er IC- 206 is installed on the machine whi le fax kit FK-506 i s not installed. *3 : Can be specified if the optional fax kit FK-506 is installed. LDAP SETTING LDA ...

  • Konica Minolta 181 - page 148

    Network settings 7 IC-206 7-9 7.3 NETWORK SETTING Network settings are specified from the “ADMI N. MANA GEMENT” menu in Utility mode. This section provides deta ils on specifying settings for the following param- eters. - IP ADDRESS SETTING - SUBNET MASK - GATEWAY - DNS CONFIG - GATEWAY TX - WEB SETTING - LPD SETTING - SLP SETTING - SNMP SETTIN ...

  • Konica Minolta 181 - page 149

    7 Network settings 7-10 IC-206 2 Press the [ , ] or [ + ] key until “ADMIN. MANAGEMENT” is selected, and then press the [OK] key. 3 Type in the administrator acc ess code, and then press the [OK] key. – The manufactur er’s default se tting is “000000 ”. – If the number was incorrectly entere d, press the [Clear/Stop] key to erase the ...

  • Konica Minolta 181 - page 150

    Network settings 7 IC-206 7-11 5 In the “NETWORK SETTING” m enu, press the [ , ] or [ + ] key until “IP ADDRESS SETTING” is sel ected, and then press the [OK] key. 6 Press the [ , ] or [ + ] key until “AUTO” or “SPECIFY” is selected, and then press the [OK] key. – If “AUTO” was selected , the IP address will automatically be o ...

  • Konica Minolta 181 - page 151

    7 Network settings 7-12 IC-206 8 Use the keypad to type in the subn et mask, and then press the [OK] key. – For the subnet mask, consult with the network administrator. 9 Use the keypad to type in the gateway. 10 Press the [OK] key. After the message “ACCEPTED” a ppears, the “NETWOR K SETTING” menu appears again. 11 Press the [Reset] key ...

  • Konica Minolta 181 - page 152

    Network settings 7 IC-206 7-13 2 Reminder In order to apply the new settings, th e machine must be turned off, then on again to be re started. Specifying the DNS settings 1 In the “NETWORK SETTING” menu, press the [ , ] or [ + ] key until “DNS CONFIG.” is sele cted, and then press the [ OK] key. 2 Press the [ , ] or [ + ] key until “DISAB ...

  • Konica Minolta 181 - page 153

    7 Network settings 7-14 IC-206 4 Press the [OK] key. After the message “ACCEPTED” a ppears, the “NETWOR K SETTING” menu appears again. 5 Press the [Reset] key in the cont rol panel. – After the screen shown above appears, turn the machine off, then on again to restart it. 2 Reminder In order to apply the new settings, th e machine must be ...

  • Konica Minolta 181 - page 154

    Network settings 7 IC-206 7-15 – Whether “DISABLE” or “ENABLE” is selected, the message “AC- CEPTED” appears, and then th e “NETWORK SETTING” menu ap- pears again. 2 Note The setting for gateway transmissions appears when optional fax kit FK- 506 is instal led. Specifying the WEB setting 1 In the “NETWORK SETTING” me nu, press ...

  • Konica Minolta 181 - page 155

    7 Network settings 7-16 IC-206 Specifying the LPD setting 1 In the “NETWORK SETTING” menu, press the [ , ] or [ + ] key until “LPD SETTING” is selected, and then press the [OK] key. 2 Press the [ , ] or [ + ] key until “DISABLE” or “E NABLE” is selected, an d then press the [OK] key. – Whether “DISABLE” or “ENABLE” is sele ...

  • Konica Minolta 181 - page 156

    Network settings 7 IC-206 7-17 Specifying the SLP setting 1 In the “NETWORK SETTING” menu, press the [ , ] or [ + ] key until “SLP SETTING” is selected, and then press the [OK] key. 2 Press the [ , ] or [ + ] key until “DISABLE” or “E NABLE” is selected, and then press the [OK] key. – Whether “DISABLE” or “ENABLE” is selec ...

  • Konica Minolta 181 - page 157

    7 Network settings 7-18 IC-206 Specifying the SNMP setting 1 In the “NETWORK SETTING” menu, press the [ , ] or [ + ] key until “SNMP SETTING” is selected, an d then press the [OK] key. 2 Press the [ , ] or [ + ] key until “DISABLE” or “E NABLE” is selected, an d then press the [OK] key. – Whether “DISABLE” or “ENABLE” is s ...

  • Konica Minolta 181 - page 158

    Network settings 7 IC-206 7-19 7.4 E-MAIL SETTING 1 E-mail transmission settings are sp ecified from the “ADMIN. MANAGE- MENT” menu in Utility mode. This section provides deta ils on specifying settings for the following param- eters. - SENDER NAME - E-MAIL ADDRESS - SMTP SERVER ADDRESS - SMTP PORT NO. - SMTP TIMEOUT - TEXT INSERT - DEFAULT SUB ...

  • Konica Minolta 181 - page 159

    7 Network settings 7-20 IC-206 2 Press the [ , ] or [ + ] key until “ADMIN. MANAGEMENT” is selected, and then press the [OK] key. 3 Type in the administrator acc ess code, and then press the [OK] key. – The manufactur er’s default se tting is “000000 ”. 4 Press the [ , ] or [ + ] key until “E-MAIL SETTING 1” is selected, and th en p ...

  • Konica Minolta 181 - page 160

    Network settings 7 IC-206 7-21 5 In the “E-MAIL SETTING 1” menu, press the [ , ] or [ + ] key until “SEND- ER NAME” is selected , an d then press the [OK] key. 6 Type in the sender’s name. – The sender’s name can contain a max imum of 20 characters. 7 Press the [OK] key. After the message “ACCE PTED” appears, t he “E-MAIL SETTIN ...

  • Konica Minolta 181 - page 161

    7 Network settings 7-22 IC-206 Specifying the e-mail address of the sender 1 In the “E-MAIL SETTING 1” menu, pre ss the [ , ] or [ + ] key unti l “E-MAIL ADDRESS” is se lected, and then press the [OK] key. 2 Type in the e- mail address of the sender. – The e-mail address ca n contain a maximum of 64 charac ters. – If this machine will n ...

  • Konica Minolta 181 - page 162

    Network settings 7 IC-206 7-23 Specifying the SMTP server address 1 In the “E-MAIL SETTING 1” menu, press the [ , ] or [ + ] key until “SMTP SERVER ADDR.” is s elected, and then press the [OK] key. 2 Type in the IP address or host na me for the SMTP server. Press the [OK] key . – The host name can contain a maximum of 64 characters. – T ...

  • Konica Minolta 181 - page 163

    7 Network settings 7-24 IC-206 Specifying the SMTP port number 1 In the “E-MAIL SETTING 1” menu, press the [ , ] or [ + ] key until “SMTP PORT NO.” is selected, and then press the [OK] key. 2 Type in the port number of the SMTP s erver. – A port number between 1 and 65535 can be spec ified. Normally, port number 25 is used. 3 Press the [O ...

  • Konica Minolta 181 - page 164

    Network settings 7 IC-206 7-25 2 T y p e i n t h e l e n g t h o f t i m e ( i n s e c o nds) until the connection to the SMTP server times out. – The timeout period can be set be tween 30 and 300 seconds. 3 Press the [OK] key. After the message “ACCE PTED” appears, t he “E-MAIL SETTING 1” menu appears again. Specifying the text input set ...

  • Konica Minolta 181 - page 165

    7 Network settings 7-26 IC-206 Specifying the subject of e-mail messages 1 In the “E-MAIL SETTING 1” menu, press the [ , ] or [ + ] key until “DE- FAULT SUBJECT” is selected, and then press the [OK] key. 2 Type in the subject for e-mail messages. – The subject can contain a m aximum of 20 ch aracters. 3 Press the [OK] key. After the messa ...

  • Konica Minolta 181 - page 166

    Network settings 7 IC-206 7-27 Specifying the POP before SMTP setting 1 In the “E-MAIL SETTING 1” menu, press the [ , ] or [ + ] key until “POP BEFORE SMTP” is selected, and the n press the [OK] key. 2 Press the [ , ] or [ + ] key until “OFF” or “ON” is selected, and then press the [OK] key. – If “OFF” is selected, the message ...

  • Konica Minolta 181 - page 167

    7 Network settings 7-28 IC-206 2 Note “E-MAIL MODE” is available only wh en optional fax kit FK-506 is in- stalled. For details on specifying the settings, refer to th e User’s Guide for fax kit FK-506. ...

  • Konica Minolta 181 - page 168

    Network settings 7 IC-206 7-29 7.5 E-MAIL SETTING 2 E-mail reception settings are specif ied from the “ADMIN. MANAGEMENT” menu in Utility mode. This section provides deta ils on specifying settings for the following param- eters. - POP3 SERVER ADDRESS - POP3 PORT NO. - POP3 SERVER TIMEOUT - POP3 ACCOUNT - POP3 PASSWORD Specifying the POP3 serve ...

  • Konica Minolta 181 - page 169

    7 Network settings 7-30 IC-206 3 Type in the administrator acc ess code, and then press the [OK] key. – The manufactur er’s default se tting is “000000 ”. 4 Press the [ , ] or [ + ] key until “E-MAIL SETTING 2” is selected, and th en press the [OK] key. – If fax kit FK-506 is installed 5 In the “E-MAIL SETTING 2” menu, press the [ ...

  • Konica Minolta 181 - page 170

    Network settings 7 IC-206 7-31 6 Type in the IP address or host name for the POP3 server. – The host name can contain a maximum of 64 characters. – To specify a host name for the POP3 server, the DNS setting must be specified. – For the IP address or host name of the POP3 server, consult with the network administrator. 7 Press the [OK] key. A ...

  • Konica Minolta 181 - page 171

    7 Network settings 7-32 IC-206 2 Type in the port number of the POP3 server. – A port number between 1 and 65535 can be spec ified. Normally, port number 110 is used. 3 Press the [OK] key. After the message “ACCEPTED” app ears, the “E-MAIL SETTING 2” menu appears again. Specifying the POP3 serv er connection timeout 1 In the “E-MAIL SET ...

  • Konica Minolta 181 - page 172

    Network settings 7 IC-206 7-33 Specifying the POP3 account 1 In the “E-MAIL SETTING 2” menu, press the [ , ] or [ + ] key until “POP3 ACCOUNT” is selected, and then press the [OK] key. 2 Type in the account name . – The account name ca n contain a maximum of 64 characters. – For the account name, consult with the network administrator. ...

  • Konica Minolta 181 - page 173

    7 Network settings 7-34 IC-206 Specifying the POP3 password 1 In the “E-MAIL SETTING 2” menu, press the [ , ] or [ + ] key until “POP3 PASSWORD” is selected, and then press the [OK] key. 2 Type in the password. – The password can contain a maximu m of 32 characters. – For the password, consult wi th the network administ rator. 3 Press t ...

  • Konica Minolta 181 - page 174

    Network settings 7 IC-206 7-35 7.6 LDAP SETTING Specify the necessary settings in orde r to use the LDAP (Lightweight Direc- tory Access Protocol) server on the network. LDAP settings are specified from th e “ADMIN. MANAGEMENT” menu in Util- ity mode. This section provides deta ils on specifying settings for the following param- eters. - LDAP S ...

  • Konica Minolta 181 - page 175

    7 Network settings 7-36 IC-206 2 Press the [ , ] or [ + ] key until “ADMIN. MANAGEMENT” is selected, and then press the [OK] key. 3 Type in the administrator acc ess code, and then press the [OK] key. – The manufactur er’s default se tting is “000000 ”. – If the number was incorrectly entere d, press the [Clear/Stop] key to erase it, ...

  • Konica Minolta 181 - page 176

    Network settings 7 IC-206 7-37 5 In the “LDAP SETTING” menu, press the [ + ] or [ , ] key until “LDAP SERVER ADDR.” is s elected, and then press the [OK] key. 6 Type in the IP address or host name for the LDAP server. – The host name can contain a maximum of 64 characters. – To specify a host name for the LDAP server, the DN S setting m ...

  • Konica Minolta 181 - page 177

    7 Network settings 7-38 IC-206 2 Type in the port number. – A port number between 1 and 65535 can be spec ified. Normally, port number 389 is used. If SSL is enabled, use port number 636. 3 Press the [OK] key. After the message “ACCEPTED” ap pears, the “LDAP SETTING” menu appears again. Selecting the SSL setting 1 In the “LDAP SETTING? ...

  • Konica Minolta 181 - page 178

    Network settings 7 IC-206 7-39 Specifying the search base 1 In the “LDAP SETTING” menu, press the [ + ] or [ , ] key until “SEARCH BASE” is sele cted, and then pres s the [OK] key. 2 Specify the database where the LDAP se rver is searched. – The search base can cont ain a maximum of 64 characters. – For the search base, consult with the ...

  • Konica Minolta 181 - page 179

    7 Network settings 7-40 IC-206 2 Type in the attribute. – The attribute can contain a maximum of 32 characters. – For the attribute, consult with the network administrator. – If the setting was incorrectly entere d, press the [Clear/Stop] key to erase it, and then type it in correctly. 3 Press the [OK] key. After the message “ACCEPTED” ap ...

  • Konica Minolta 181 - page 180

    Network settings 7 IC-206 7-41 Specifying the LDAP search timeout 1 In the “LDAP SETTING” menu, press the [ + ] or [ , ] key until “LDAP TIMEOUT” is selected, and then press the [OK] key. 2 Type in the length of time (in seco nds) until the LDAP search times out. – The timeout period can be set be tween 5 and 300 seconds. 3 Press the [OK] ...

  • Konica Minolta 181 - page 181

    7 Network settings 7-42 IC-206 2 Type in the maximu m number of items. – The maximum number of items can be set between 5 and 100. 3 Press the [OK] key. After the message “ACCEPTED” ap pears, the “LDAP SETTING” menu appears again. Selecting the authentication method 1 In the “LDAP SETTING” menu, press the [ + ] or [ , ] key until “A ...

  • Konica Minolta 181 - page 182

    Network settings 7 IC-206 7-43 2 Note For the authentication method, consult with the network administrator. The manufacture r’s default setti ng is “ANONYMOUS”. Specifying the LDAP account name 1 In the “LDAP SETTING” men u, press the [ + ] or [ , ] key until “LDAP AC- COUNT” is selecte d, and then press th e [OK] key. 2 Type in the ...

  • Konica Minolta 181 - page 183

    7 Network settings 7-44 IC-206 Specifying the LDAP password 1 In the “LDAP SETTING” menu, press the [ + ] or [ , ] key until “LDAP PASSWORD” is selected, and then press the [OK] key. 2 Type in the password. – The password can contain a maximu m of 32 characters. – For the password, consult wi th the network administ rator. – If the se ...

  • Konica Minolta 181 - page 184

    Network settings 7 IC-206 7-45 2 Type in the domain name. – The domain name can contain a maximum of 64 characters. – For the domain name, consult with the network administrator. – If the setting was incorrectly entere d, press the [Clear/Stop] key to erase it, and then ty pe it in correctly. 3 Press the [OK] key. After the message “ACCEPTE ...

  • Konica Minolta 181 - page 185

    7 Network settings 7-46 IC-206 7.7 USER SETTING The settings for the NTP server and time zone are described below. The time can be set accurat ely with the NTP server. 2 Note The settings for the NTP server and ti me zone appear only when network interface ca rd NC-503 or image controller IC-206 is installed on the ma- chine while fax kit FK-506 is ...

  • Konica Minolta 181 - page 186

    Network settings 7 IC-206 7-47 3 Type in the administrator access code, and then press the [OK] key. – The manufactur er’s default setting is “000000”. – If the code was incorrectly ent ere d, press the [Clear/ Stop] key to erase the num ber, and then type it in correctly. 4 Press the [ , ] or [ + ] key until “USER SETTING” is selecte ...

  • Konica Minolta 181 - page 187

    7 Network settings 7-48 IC-206 – If an NTP server was specified: The date and time that data is sent with the Scan to E-Mail or Scan to FTP operation are a utomatically added to the data at the sa me time that the transmission date and time are re corded in the trans- mission log. – If an NTP server was not specified: Only a transmission number ...

  • Konica Minolta 181 - page 188

    Network settings 7 IC-206 7-49 3 Type in the administrator access code, and then press the [OK] key. – The manufactur er’s default setting is “000000”. – If the code was incorrectly ent ere d, press the [Clear/ Stop] key to erase the num ber, and then type it in correctly. 4 Press the [ , ] or [ + ] key until “USER SETTING” is selecte ...

  • Konica Minolta 181 - page 189

    7 Network settings 7-50 IC-206 The message “ACCEPTED” appears, and then the “USER SETTING” menu appears again. 7 Press the [ , ] or [ + ] key until “RETURN” is selected, and then press the [OK] key . ...

  • Konica Minolta 181 - page 190

    Registering destinations 8 IC-206 8-1 8 Registering destinations This chapter provides descriptions of the procedures for registering destina- tion addresses. 8.1 Registering destinations Destinations can be re gistered from the machine’s c ontrol panel or from Pa- geScope Web Connection. The followin g procedures describe how to regis- ter desti ...

  • Konica Minolta 181 - page 191

    8 Registering destinations 8-2 IC-206 Registering one-touch dial destinations 2 Note In order to use the one-touch dial destinations, optional fax kit FK-506 must be installed. 1 Press the [Utility] key in the control pane l. 2 Press the [ , ] or [ + ] key until “DIAL REGISTRAT ION” is selected, and then press the [OK] key. Scan to Server (FTP) ...

  • Konica Minolta 181 - page 192

    Registering destinations 8 IC-206 8-3 3 Press the [ , ] or [ + ] key until “ONE-TOUCH DIAL” is selected, and then press the [OK] key. 4 Press the one-touch dial key to be programmed . – One-touch dial keys 01 to 32 can be programmed. The number of the key to be progra mmed appears, and then the scre en for registering settings appears. ...

  • Konica Minolta 181 - page 193

    8 Registering destinations 8-4 IC-206 5 Select “MANUAL SETTING” or “L DAP SEARCH”, and then press the [OK] key . – If “MANUAL SETTING” was selected, conti nue with step 6 . – If “LDAP SEARCH” was selected, continue wit h step 9. 6 If “MANUAL SETTING” was selected, type in the n ame of the destina- tion, and then press the [O ...

  • Konica Minolta 181 - page 194

    Registering destinations 8 IC-206 8-5 8 Press the [OK] key. After the message “REGISTERED” appears, the “DIAL REGISTRA- TION” menu appears again. 9 To perform an LDAP search, select “LDAP SEARCH” in the “ONE- TOUCH DIAL” menu, and then press the [OK] key. 10 Select “NAME” or “E-MAIL” for th e destination information to be se ...

  • Konica Minolta 181 - page 195

    8 Registering destinations 8-6 IC-206 –E - M A I L – A maximu m of 10 charac ters can be entered to be searched for. – The registration name or e-ma il address searched for differs de- pending on the search method select ed with the “SEARCH METH- OD” parameter in th e “LDAP SETTING” menu. If “BEGIN” was selected, the regis t ratio ...

  • Konica Minolta 181 - page 196

    Registering destinations 8 IC-206 8-7 – Press the [ ) ] key to display the destination name and e-mail ad- dress. After checking th e displayed information, press the [OK] key. If the wrong destinatio n was selected, press the [Back] key to return to the previous screen. – If the e-mail address that was found contains 64 characters or more, the ...

  • Konica Minolta 181 - page 197

    8 Registering destinations 8-8 IC-206 2 Note Pressing the [ , ] key allows the transmission size and resolution for send- ing Internet faxes to be specified. These settings are applied when a transmission is specified using the procedure for Internet fax transmis- sions. The settings are not applie d when a transmission is spec ified using the proc ...

  • Konica Minolta 181 - page 198

    Registering destinations 8 IC-206 8-9 3 Press the [ , ] or [ + ] key until “SPEED DIAL” is selected, and then press the [OK] key. 4 Type in the speed dial number to be progr ammed, and then press [OK] key. – Speed dial numbers 001 through 240 can be programmed from the control panel. The speed dial number to be pr ogrammed appears, and then t ...

  • Konica Minolta 181 - page 199

    8 Registering destinations 8-10 IC-206 6 If “MANUAL SETTING” was selected, type in the n ame of the destina- tion, and then press the [OK] key. 7 Type in the e-mail address of the recipient. – “OTHER SETTING= , ” appears only if fax kit FK-506 is installed, the transmission size and resoluti on for sending Internet faxes can be specified. ...

  • Konica Minolta 181 - page 200

    Registering destinations 8 IC-206 8-11 10 Select “NAME” or “E-MAIL” for th e destination information to be searched, and then press the [OK] ke y. – The remainder of the procedure is the same, regardless of whether “NAME” or “E-MAIL” is sele cted. “LDAP SEARCH (NAME)” or “LDAP SEARCH (E-MAIL)” appears in the corresponding ...

  • Konica Minolta 181 - page 201

    8 Registering destinations 8-12 IC-206 – If the text was incorrectly entere d, press the [Clear/Stop] key to erase it, and then type it in correctly. After the message “SEARCHING” appe ars, the list of corresponding registration names or e-mail addresses appears. 12 Press the [ , ] or [ + ] key until the desired registration name or e-m ail a ...

  • Konica Minolta 181 - page 202

    Registering destinations 8 IC-206 8-13 13 After checking the displayed dest ination name, press the [OK] key. 14 After checking the displayed e-mail a ddress of the recipient, press the [OK] key . After the message “REGISTERED” appears, the “DIAL REGISTRA- TION” menu appears again. 2 Note Pressing the [ , ] key allows the transmission size ...

  • Konica Minolta 181 - page 203

    8 Registering destinations 8-14 IC-206 Registering speed dial de stinations (FTP se rvers) The FTP server address where scan data is to be sent can be registered with speed dial numbers 241 to 250. 2 Note An FTP server address can only be registered wi th a speed dial number from Administrator mode of PageSc ope Web Connection. For details on acces ...

  • Konica Minolta 181 - page 204

    Registering destinations 8 IC-206 8-15 3 Press the [ , ] or [ + ] key until “GROUP DIAL” is selected, and then press the [OK] key. 4 Press the one-touch dial key to be programmed for group dialing. The number of the one-touch dial ke y to be programmed for group di- aling appears with a screen for registering settings. ...

  • Konica Minolta 181 - page 205

    8 Registering destinations 8-16 IC-206 5 Type in the n ame of the destination, and th en press the [OK] ke y. 6 With the one-touch dial keys and speed dial numbers, specify the re- cipient. The recipient information a ppears. Press the [OK] key . 7 To add a recipient to the group, press the [ , ] or [ + ] key until “ADD” is selected, and then p ...

  • Konica Minolta 181 - page 206

    Registering destinations 8 IC-206 8-17 10 Press the [ , ] or [ + ] key until “RETURN” is sele cted, and then press the [OK] key . After the message “REGISTERED” appears, the “DIAL REGISTRA- TION” menu appears again. ...

  • Konica Minolta 181 - page 207

    8 Registering destinations 8-18 IC-206 8.2 Editing or deleting registered informat ion Editing or deleting a on e-touch dial destination 1 Press the [Utility] key in the control pane l. 2 Press the [ , ] or [ + ] key until “DIAL REGISTRAT ION” is selected, and then press the [OK] key. 3 Press the [ , ] or [ + ] key until “ONE-TOUCH DIAL ” i ...

  • Konica Minolta 181 - page 208

    Registering destinations 8 IC-206 8-19 4 Press the one-touch dial key fo r the de stination to be edited or deleted. After the registered information is displayed, the follo wing screen ap- pears. – If a group dial destination or program is registered with the selected one-touch dial key, the message “NOT ACCEPTED” appears, and then the “DI ...

  • Konica Minolta 181 - page 209

    8 Registering destinations 8-20 IC-206 – To correct destination, press the [ Clear/Stop] to erase it, and then type in the correct destination. The destin ation is dis played. 8 Press the [OK] key. After the message “REGISTERED” appears, the “DIAL REGISTRA- TION” menu appears again. 2 Note If an edited one-touc h dial destinatio n is regi ...

  • Konica Minolta 181 - page 210

    Registering destinations 8 IC-206 8-21 2 Press the [ , ] or [ + ] key until “DIAL REGISTRAT ION” is selected, and then press the [OK] key. 3 Press the [ , ] or [ + ] key until “SPEED DIAL” is selected, and then press the [OK] key. 4 Type in the speed dial number for the destination to be edited or delet- ed, and then press the [OK] key. Aft ...

  • Konica Minolta 181 - page 211

    8 Registering destinations 8-22 IC-206 6 To edit the information, select “E DIT”, and then press the [OK] key. The name of the registered destinati on is displayed. – To correct destination name, press the [Clear/Stop ] to erase it, and then type in the correct destination name. The name of the registered destinati on is displayed. 7 Press th ...

  • Konica Minolta 181 - page 212

    Registering destinations 8 IC-206 8-23 Editing or deleting a group d ial destination 1 Press the [Utility] key in the control panel. 2 Press the [ , ] or [ + ] key until “DIAL REGISTRAT ION” is selected, and then press the [OK] key. 3 Press the [ , ] or [ + ] key until “GROUP DIAL” is selected, and then press the [OK] key. ...

  • Konica Minolta 181 - page 213

    8 Registering destinations 8-24 IC-206 4 Press the one-touch dial key programmed with the group to be edited or deleted. After the registered information is displayed , the following screen ap- pears. – If a one-touch di al destination or program is registered wit h the se- lected one-touch dial key, the message “NOT ACCEPTED” ap- pears, and ...

  • Konica Minolta 181 - page 214

    Registering destinations 8 IC-206 8-25 7 Press the [OK] key. The following screen appears. – To add a recipient to the group, press the [ , ] or [ + ] key until “ADD” is selected, and the n press the [OK] key. 8 With the one-touch dial keys and sp eed dial numbers, enter the recip- ient to be registered. The new recipient registered with the ...

  • Konica Minolta 181 - page 215

    8 Registering destinations 8-26 IC-206 ...

  • Konica Minolta 181 - page 216

    Performing a Scan to E-mail operat ion 9 IC-206 9-1 9 Performing a Scan to E-mail operation This chapter provides descriptions of the procedures for se nding scan data as e-mail messages. 9.1 Basic transmission 2 Reminder With the Scan to E-mail operation, documents are sent through a mail server. In add ition, as soon as tr ansm ission with the se ...

  • Konica Minolta 181 - page 217

    9 Performing a Scan to E-mail operation 9-2 IC-206 2 Load the document to be sent in to the document feeder. – Adjust the document guides to fit the size of the document. – Load the document pages with th e side to be scanned face up. – For information on documents that can be used an d the scanning area of the image , refer to the Us er’s ...

  • Konica Minolta 181 - page 218

    Performing a Scan to E-mail operat ion 9 IC-206 9-3 4 Press the [Start] key. Scanning and transmission begins. 2 Note E-mail addresses specified after the [Scan] key is pressed are set as Scan to E-mail recipients. Up to 64 characters ca n be entered. To stop scanning, press the [Clear/Stop] key. If the transmission could not be co mpleted correctl ...

  • Konica Minolta 181 - page 219

    9 Performing a Scan to E-mail operation 9-4 IC-206 Positioning documents on the or iginal glass 2 Note E-mail addresses specified after the [Scan] key is pressed are set as Scan to E-mail recipients. 1 Press the [Scan] key. The machine enters Scan mode, an d the Scan mode screen appears. ...

  • Konica Minolta 181 - page 220

    Performing a Scan to E-mail operat ion 9 IC-206 9-5 2 Lift open the original cover, and then position the document to be sent on the original glass. – Load the document page with the side to be scanned face down. – Align the documen t on the scales ab ove and to the lef t of the orig- inal glass. – For information on documents that can be use ...

  • Konica Minolta 181 - page 221

    9 Performing a Scan to E-mail operation 9-6 IC-206 – The destination can be specified using any of the following proce- dures. Refer to “Specifying a one-touch dial de stination” on page 9 -33. (One-touch dial de stinations are ava ilable only when opti onal fax kit FK-506 is installed.) Refer to “Specifying a speed di al destination” on ...

  • Konica Minolta 181 - page 222

    Performing a Scan to E-mail operat ion 9 IC-206 9-7 When “AUTO DETECTION” is selected 1 If “AUTO DETECTION” was selected in step 5 and the [OK] k ey is pressed, the followi ng screen appears. 2 Press the [OK] key. The message “SCANNING” appears, and the following screen appears when scanning is finished. – When scanning a document tha ...

  • Konica Minolta 181 - page 223

    9 Performing a Scan to E-mail operation 9-8 IC-206 When “MANUAL” is selected 2 Note If “MANUAL” was selected, the scanning size can be changed. The settings available for the sc anning size are METRIC (“A3 w ”, “A4 w ”, “A4 v ”, “A5 w ”, “A5 v ”, “ B4 w ”, “B5 w ”, “B5 v ”, “FLS w ”, “8K w ”, “16K w ...

  • Konica Minolta 181 - page 224

    Performing a Scan to E-mail operat ion 9 IC-206 9-9 3 Press the [OK] key. The message “SCANNING” appears, and the following screen appears when scanning is finished. – When scanning a document that contains mu ltiple pages, position the next page of the d ocument on the original glass, and th en press the [OK] key. Repeat this step until all ...

  • Konica Minolta 181 - page 225

    9 Performing a Scan to E-mail operation 9-10 IC-206 9.2 Changing the transmission settings From the “SCAN OTHER SETTING” menu, settings for the subject, cc ad- dress, file format and compression encodi ng method can be specified for the scanned data. Specifying the subject 1 Press the [Scan] key. The machine enters Scan mode, an d the Scan mode ...

  • Konica Minolta 181 - page 226

    Performing a Scan to E-mail operat ion 9 IC-206 9-11 3 Press the [ , ] key. The “SCAN OTHER SETTING” menu appears. 4 Press the [ , ] or [ + ] key until “SUBJECT” is selected, and then pr ess the [OK] key. 5 Type in the subject (title) for the e-mail message to be sent, and then press the [OK] key. The “SCAN OTHER SETTING” menu appears a ...

  • Konica Minolta 181 - page 227

    9 Performing a Scan to E-mail operation 9-12 IC-206 The machine enters Scan mode, an d the Scan mode screen appears. 2 Position the document , and then specif y the reci pient. “OTHER SETTING= , ” appears. 3 Press the [ , ] key. The “SCAN OTHER SETTING” menu appears. 4 In the “SCAN OTHER SETTING” menu, press the [ , ] or [ + ] key until ...

  • Konica Minolta 181 - page 228

    Performing a Scan to E-mail operat ion 9 IC-206 9-13 5 Enter the e-mail a ddress of the recipient t hat you wish to send a copy (cc) to, and then press the [OK] key. A menu containing “ADD” and “CHECK/EDIT” appears. – To send a copy (cc) to multiple recipients, select “ADD”, and then press the [OK] key. When the screen for entering th ...

  • Konica Minolta 181 - page 229

    9 Performing a Scan to E-mail operation 9-14 IC-206 2 Press the [ , ] or [ + ] key until the address to be checked or edited is se- lected. – If the [Clear/Stop] key is presse d, the DELETE screen appears. Press the [ , ] or [ + ] key until “YES” is selected, and th en press the [OK] key. The message “DELETED ” appears, the selected addre ...

  • Konica Minolta 181 - page 230

    Performing a Scan to E-mail operat ion 9 IC-206 9-15 3 While the list of cc addr esses is displayed, press the [Back] key. The “CC ADDRESS” menu (whic h contai ns “ADD” and “CHECK/EDIT”) ap- pears. 4 Press the [ , ] or [ + ] key until “RETURN” is sele cted, and then press the [OK] key . The “SCAN OTHER SETTING” menu appears agai ...

  • Konica Minolta 181 - page 231

    9 Performing a Scan to E-mail operation 9-16 IC-206 2 Position the document , and then specif y the reci pient. “OTHER SETTING= , ” appears. 3 Press the [ , ] key. The “SCAN OTHER SETTING” menu appears. 4 Press the [ , ] or [ + ] key until “IMAGE FORMAT” is selected, and then press the [OK] key. 5 Press the [ , ] or [ + ] key until eith ...

  • Konica Minolta 181 - page 232

    Performing a Scan to E-mail operat ion 9 IC-206 9-17 Selecting the compression encoding method 1 Press the [Scan] key. The machine enters Scan mode, an d the Scan mode screen appears. 2 Position the document, and then specify the recipient . “OTHER SETTING= , ” appears. 3 Press the [ , ] key. The “SCAN OTHER SETTING” menu appears. ...

  • Konica Minolta 181 - page 233

    9 Performing a Scan to E-mail operation 9-18 IC-206 4 Press the [ , ] or [ + ] key until “CODING METHOD ” is selected, and then press the [OK] key. 5 Press the [ , ] or [ + ] key until “MH”, “MR” or “MMR” is selected as the compression encoding method. 6 Press the [OK] key. After the message “ACCEPTED” a ppears, the “SCAN OTHE ...

  • Konica Minolta 181 - page 234

    Performing a Scan to E-mail operat ion 9 IC-206 9-19 9.3 Changing the scanni ng quality settings From the “QUALITY” menu (which co ntains “RESOLUTION” and “O RIGI- NAL”), the scanning quality (resolution and document quality) settings can be changed. If the settings are not ch anged, the scan data is sent with the scan settings displaye ...

  • Konica Minolta 181 - page 235

    9 Performing a Scan to E-mail operation 9-20 IC-206 2 Press the [Quality] key. 3 Press the [ , ] or [ + ] key until “RESOLUTION” is selected, and then press the [OK] key. 4 Press the [ , ] or [ + ] key to select the appropriate resolution. – The settings available for the resolution are “150×1 50dpi”, “300×300dpi” and “600×600dpi ...

  • Konica Minolta 181 - page 236

    Performing a Scan to E-mail operat ion 9 IC-206 9-21 Selecting the document quality 1 Press the [Scan] key. The machine enters Scan mode, an d the Scan mode screen appears. 2 Press the [Quality] key. ...

  • Konica Minolta 181 - page 237

    9 Performing a Scan to E-mail operation 9-22 IC-206 3 Press the [ , ] or [ + ] key until “ORIGINAL” is selected, and then press the [OK] key. 4 Press the [ , ] or [ + ] key until the type of docu ment to be attached to e- mail messages is selected. – The settings available for the do cument quality are “TEXT/PHOTO”, “TEXT” and “PHOT ...

  • Konica Minolta 181 - page 238

    Performing a Scan to E-mail operat ion 9 IC-206 9-23 9.4 Changing the document scanning density From the DENSITY screen, the scanning density for the document can be changed. When “TEXT/PHOTO” or “TEXT” was selected When “TEXT/ PHOTO” or “TEX T” is select ed, the density can be specified as described below. 1 Press the [Scan] key. T ...

  • Konica Minolta 181 - page 239

    9 Performing a Scan to E-mail operation 9-24 IC-206 2 Press the [Density] key. Th e DENSI TY screen appea rs. 3 Press the [ , ] or [ + ] key until “AUTO” or “MANUAL” is selected, and then press the [OK] key. – If “AUTO” is selected, the me ssage “ACCEPTED” appears, and then the Scan mode screen app ears again with “AUTO” appea ...

  • Konica Minolta 181 - page 240

    Performing a Scan to E-mail operat ion 9 IC-206 9-25 – If “MANUAL” is selected, a scre en appears, allowing you to adjust the density. Press the [ * ] or [ ) ] key to adjust the density. Adjusting the setting to th e left reduces the density (lightens the image). Ad- justing the setting to the right increases the density (darken s the im- age ...

  • Konica Minolta 181 - page 241

    9 Performing a Scan to E-mail operation 9-26 IC-206 When “PHOTO” was selected When “PHOTO” is selected, the densit y can be specified as described be- low. 1 Press the [Scan] key. The machine enters Scan mode, an d the Scan mode screen appears. 2 Press the [Density] key. ...

  • Konica Minolta 181 - page 242

    Performing a Scan to E-mail operat ion 9 IC-206 9-27 3 Press the [ * ] or [ ) ] key to adjust the density. 4 When the [OK] key is pressed, th e message “ACCEPTED” appears, and then the Scan mode screen appears again with the adjust ed den- sity setting indicated. – If the density setting is adjusted to the left, the setting on the left side i ...

  • Konica Minolta 181 - page 243

    9 Performing a Scan to E-mail operation 9-28 IC-206 9.5 Specifying the defa ult scanning settings The default settings for the resoluti on , data format and compression encod- ing method during scanning and transmission wit h Scan to E-mail and Scan to Server (FTP) operations can be cha nged. Selecting the resolut ion 1 Press the [Utility] key. 2 P ...

  • Konica Minolta 181 - page 244

    Performing a Scan to E-mail operat ion 9 IC-206 9-29 5 Press the [OK] key, the message “ACCEPTED” appears, and th en the “SCAN SETTING” menu appears again. Selecting the file format 1 Press the [Utility] key. 2 Press the [ , ] or [ + ] key until “SCAN SETTING” is selected, and then press the [OK] key. 3 Press the [ , ] or [ + ] key unti ...

  • Konica Minolta 181 - page 245

    9 Performing a Scan to E-mail operation 9-30 IC-206 Selecting the compression encoding method 1 Press the [Utility] key. 2 Press the [ , ] or [ + ] key until “SCAN SETTING” is selected, and then press the [OK] key. 3 Press the [ , ] or [ + ] key until “CODING METHOD ” is selected, and then press the [OK] key. 4 Press the [ , ] or [ + ] key ...

  • Konica Minolta 181 - page 246

    Performing a Scan to E-mail operat ion 9 IC-206 9-31 9.6 If the memory becomes fu ll while scanning docu- ments If the memory becomes nearly full wh ile documents are being scanned, a warning message appe ars. Select whether to continue the transm ission or to cancel it. After a message appears wa rning that the memory is nearly full, the “MEM. F ...

  • Konica Minolta 181 - page 247

    9 Performing a Scan to E-mail operation 9-32 IC-206 – In the MEM. FULL/TX CANCEL screen, the message “MEMORY FULL” appears after the length of time for an automatic reset oper- ation has passed, and a transmission result report is printed . After any key is pressed, the message “JOB CANCELED” appears, and then the Scan mode screen appears ...

  • Konica Minolta 181 - page 248

    Performing a Scan to E-mail operat ion 9 IC-206 9-33 9.7 Specifying a one-to uch dial destination 2 Note In order to use the one-touch dial destinations, optional fax kit FK-506 must be installed. 1 Press the [Scan] key. The machine enters Scan mode, an d the Scan mode screen appears. ...

  • Konica Minolta 181 - page 249

    9 Performing a Scan to E-mail operation 9-34 IC-206 2 Press the one-touch dial key ([01] through [32]) programmed with the e-mail address of the recipient. 2 Note The recipient must have been register ed with a o ne-touch dial key in ad- vance. For details on programming the one-touc h dial keys, refer to “Registering destinations” on page 8-1. ...

  • Konica Minolta 181 - page 250

    Performing a Scan to E-mail operat ion 9 IC-206 9-35 9.8 Specifying a speed dial destination 1 Press the [Scan] key. The machine enters Scan mode, an d the Scan mode screen appears. ...

  • Konica Minolta 181 - page 251

    9 Performing a Scan to E-mail operation 9-36 IC-206 2 Press the [Speed Dial] key, and then use the keypad to type in the 3- digit speed dial number (number pr ogram med with the e-mail address). 3 Press the [OK] key. – The destination is specified. 2 Note The recipient must have been registered wit h a speed dial number in ad- vance. For details ...

  • Konica Minolta 181 - page 252

    Performing a Scan to E-mail operat ion 9 IC-206 9-37 9.9 Specifying a recipient fr om a group dial destination 2 Note In order to use the group dial destin ations, optional fax kit FK-506 must be installed. 1 Press the [Scan] key. The machine enters Scan mode, an d the Scan mode screen appears. ...

  • Konica Minolta 181 - page 253

    9 Performing a Scan to E-mail operation 9-38 IC-206 2 Press the one-touch dial key ([01] through [32]) programmed with the group containing the desired recipient. 2 Note The recipient must have be en registered wi th a group dial destination in advance. For details on registerin g group dial destinations, refer to “Registering destinations” on ...

  • Konica Minolta 181 - page 254

    Performing a Scan to E-mail operat ion 9 IC-206 9-39 9.10 Selecting a destinati on from the phone book The phone book con tains all destinations registered with one-touch d ial keys and speed dial numbers. In addition, in an en vironment where an L DAP serv- er is being used, the LDAP server can be searched for desti nations to be reg- istered. The ...

  • Konica Minolta 181 - page 255

    9 Performing a Scan to E-mail operation 9-40 IC-206 2 Press the [Phone Book] key. The “PHONE BOOK” menu appears. 3 Press the [ + ] or [ , ] key until “LIST”, “SEARCH” or “LDAP SEARCH” is selected, and then press the [OK] key. – If “LIST” was selected , the list of all destinations registered with one-touch dial keys and speed ...

  • Konica Minolta 181 - page 256

    Performing a Scan to E-mail operat ion 9 IC-206 9-41 – If “SEARCH” was selected, a screen appears, allowing you to type in the text to be searched for. Search for the desired recipient b y entering part (or all) of the regi stered name. For details on perfor m- ing the search in the phone book, re fer to “Searching the phone book” on page ...

  • Konica Minolta 181 - page 257

    9 Performing a Scan to E-mail operation 9-42 IC-206 2 Press the [Phone Book] key. The “PHONE BOOK” menu appears. 3 Press the [ , ] or [ + ] key until “SEARCH” is se lected, and then pre ss the [OK] key . 4 Type in the first few charac ters of the name registered for the desired recipient. – Enter part of the name registered with the on e- ...

  • Konica Minolta 181 - page 258

    Performing a Scan to E-mail operat ion 9 IC-206 9-43 5 Press the [OK] key. After the message “SEARCHING” appe ars, the search results screen appears. – If a destination co uld not be found with the entered name , the mes- sage “NOT FOUND” appears, and th en the screen shown in step 4 appears. 6 Select the destination , and then press the ...

  • Konica Minolta 181 - page 259

    9 Performing a Scan to E-mail operation 9-44 IC-206 Searching the LDAP server 1 Press the [Scan] key. The machine enters Scan mode, an d the Scan mode screen appears. 2 Press the [Phone Book] key. ...

  • Konica Minolta 181 - page 260

    Performing a Scan to E-mail operat ion 9 IC-206 9-45 3 Press the [ + ] or [ , ] key until “LDAP S EARCH” is selected, and then press the [OK] key. 4 Select “NAME” or “E-MAIL” for th e destination information to be searched, and then press the [OK] ke y. – The remainder of the procedure is the same, regardless of whether “NAME” or ...

  • Konica Minolta 181 - page 261

    9 Performing a Scan to E-mail operation 9-46 IC-206 –E - M A I L – A maximu m of 10 charac ters can be entered to be searched for. – The registration name or e-ma il address searched for differs de- pending on the search method select ed with the “SEARCH METH- OD” parameter in th e “LDAP SETTING” menu. If “BEGIN” was selected, the ...

  • Konica Minolta 181 - page 262

    Performing a Scan to E-mail operat ion 9 IC-206 9-47 – Press the [ ) ] key to display the destination name and e-mail ad- dress. If the wrong destination wa s selected, press the [Back] key to return to the previous screen. – If the e-mail address that was found contains 64 characters or more, the message “CAUTION” appe ars, and then the ? ...

  • Konica Minolta 181 - page 263

    9 Performing a Scan to E-mail operation 9-48 IC-206 9.11 Checking the communication results The communication results for scan data can be viewed. 1 Press the [Scan] key. The machine enters Scan mode, an d the Scan mode screen appears. 2 Press the [Confirm] key. The “CONFIRM MODE” menu appears. ...

  • Konica Minolta 181 - page 264

    Performing a Scan to E-mail operat ion 9 IC-206 9-49 3 Press the [ , ] or [ + ] key u ntil “TX/RX RESULT” is sel ected. – If fax kit FK-506 is installed. 4 Press the [OK] key. All communication results are displayed. – The communication results appear starting with the most recent jobs. Press the [ , ] key to display communica tion results ...

  • Konica Minolta 181 - page 265

    9 Performing a Scan to E-mail operation 9-50 IC-206 5 Press the [OK] key. The Scan mode s creen appears again . ...

  • Konica Minolta 181 - page 266

    Performing a Scan to Server (FTP) operat ion 10 IC-206 10-1 10 Performing a Scan to Server (FTP) oper- ation This chapter provides descriptions of the procedures for se nding scan data to servers. 10.1 Basic transmission In order to perform a Scan to Server ( FTP) operation, ce rtain settings such as the FTP server address must be specified in adva ...

  • Konica Minolta 181 - page 267

    10 Performing a Scan to Server (FTP) operation 10-2 IC-206 The machine enters Scan mode, an d the Scan mode screen appears. 2 Load the document to be sent in to the document feeder. – Adjust the document guides to fit the size of the document. – Load the document pages with th e side to be scanned face up. – For information on documents that ...

  • Konica Minolta 181 - page 268

    Performing a Scan to Server (FTP) operat ion 10 IC-206 10-3 3 Press the [Speed Dial] key, and then use the keypad to type in the 3- digit speed dial number (number programmed with the address of the FTP server where the data is to be uploa ded). – When the destination address is entered, “OTHER SETTING= , ” appears. To change tran smission se ...

  • Konica Minolta 181 - page 269

    10 Performing a Scan to Server (FTP) operation 10-4 IC-206 Scanning begins, a connection to the FTP server is established, and uploading of the scan data begins. 2 Note To stop scanning, press the [Clear/Stop] key. If the transmission could not be comp leted correctly, a transmi ssion re- sult report is printed. To cancel a queued transmission of s ...

  • Konica Minolta 181 - page 270

    Performing a Scan to Server (FTP) operat ion 10 IC-206 10-5 Positioning documents on the or iginal glass 1 Press the [Scan] key. The machine enters Scan mode, an d the Scan mode screen appears. 2 Lift open the original cover, and then position the document to be sent on the original glass. – Load the document page with the side to be scanned face ...

  • Konica Minolta 181 - page 271

    10 Performing a Scan to Server (FTP) operation 10-6 IC-206 – Align the documen t on the scales abov e and to the left of the orig- inal glass. – For information on documents that can be used an d the scanning area of the image , refer to the Us er’s Guide included with the ma- chine. 3 Press the [Speed Dial] key, and then use the keypad to ty ...

  • Konica Minolta 181 - page 272

    Performing a Scan to Server (FTP) operat ion 10 IC-206 10-7 5 Press the [Start] key. 6 The “BOOK SCAN” menu appears. Press the [ , ] or [ + ] key until “AUTO DETECTION” is selecte d, and then press the [OK] key. – The remainder of the procedure di ffers depending on whether “AU- TO DETECTION” or “MANUAL” was selected. ! Detail Onl ...

  • Konica Minolta 181 - page 273

    10 Performing a Scan to Server (FTP) operation 10-8 IC-206 When “AUTO DETECTION” is selected 1 If “AUTO DETECTION” was selected in step 6 and the [OK] key is pressed, the follow ing screen appears . 2 Press the [OK] key. The message “SCANNING” appears, and the following screen appears when scanning is finished. – When scanning a docum ...

  • Konica Minolta 181 - page 274

    Performing a Scan to Server (FTP) operat ion 10 IC-206 10-9 When “MANUAL” is selected 2 Note If “MANUAL” was selected, the scanning size can be changed. The settings available for the s cannin g size are METRIC (“A3 w ”, “A4 w ”, “A4 v ”, “A5 w ”, “A5 v ”, “ B4 w ”, “B5 w ”, “B5 v ”, “FLS w ”, “8K w ” ...

  • Konica Minolta 181 - page 275

    10 Performing a Scan to Server (FTP) operation 10-10 IC-206 3 Press the [OK] key. The message “SCANNING” appears, and the following screen appears when scanning is finished. – When scanning a document that conta ins multiple pages, position the next page of the docume nt on the original glass, and then press the [OK] key. Repeat this step unt ...

  • Konica Minolta 181 - page 276

    Performing a Scan to Server (FTP) operat ion 10 IC-206 10-11 10.2 If the memory becomes full while scanning docu- ments If the memory becomes nearly full wh ile documents are being scanned, a warning message appe ars. Select whether to continue the transm ission or to cancel it. After a message appears wa rning that the memory is nearly full, the ? ...

  • Konica Minolta 181 - page 277

    10 Performing a Scan to Server (FTP) operation 10-12 IC-206 – In the MEM. FULL/TX CANCEL screen, the message “MEMORY FULL” appears after the length of time for an automatic reset oper- ation has passed, and a transmission result report is printed . After any key is pressed, the message “JOB CANCELED” appears, and then the Scan mode screen ...

  • Konica Minolta 181 - page 278

    Using PageScope Web Connection 11 IC-206 11-1 11 Using PageScope Web Connection 11.1 When using PageScope Web Connection In order to use PageScope Web Connectio n, optional network interface card NC-503 and image controller IC-206 must be installed. 11.2 About PageScope Web Connection PageScope Web Connection is a device ma n agement utility integr ...

  • Konica Minolta 181 - page 279

    11 Using PageScope Web Connection 11-2 IC-206 Using PageScope Web Connection, the following o perations can be per- formed. - Changing the settings – Registering destination dialing – Changing printer setti ngs (when IC-206 is installe d) – Changing network sett ings - Remotely ma naging the stat us – Viewing this machine paper tray in form ...

  • Konica Minolta 181 - page 280

    Using PageScope Web Connection 11 IC-206 11-3 11.3 System requirements 2 Reminder In order to use PageScope Web Conn ection, optional network interface card NC-503 a nd image controlle r IC-206 must be installed. Network Ethernet (T CP/IP) Operating system Windows 98 SE, Windows Me, Windows 2000, Window s XP, Windows Server 2003 Compatible Web brow ...

  • Konica Minolta 181 - page 281

    11 Using PageScope Web Connection 11-4 IC-206 11.4 Accessing PageSc ope Web Connection PageScope Web Connection can be acc essed directly from a Web browser. 1 Start the Web browser. 2 In the Address bar, type the followin g IP address for the machine, and then press the [Enter] key. – http://<IP_address_for_this_machine>/ (Example) If the ...

  • Konica Minolta 181 - page 282

    Using PageScope Web Connection 11 IC-206 11-5 11.5 Structure of pages The following page appears when the mac hine is accessed with PageScope Web Connectio n. 2 Reminder The pages and dialog boxes shown in th is manual may differ from those that appear on your c o mputer. In addition, the specifications and other information concernin g this produc ...

  • Konica Minolta 181 - page 283

    11 Using PageScope Web Connection 11-6 IC-206 2 Note The Print tab appears only if the image controller IC-206 is installed. The PageScope Web Connec tion pages appear diff erently depending on the options installed on th e machine and the specified machine settin gs. Operation In PageScope Web Conn ection, click a tab, sel ect a function ca tegory ...

  • Konica Minolta 181 - page 284

    Using PageScope Web Connection 11 IC-206 11-7 2 Reminder The menus and commands may vary de pending on the Web browser ver- sion. For details, refer to the Help for the Web browser . If the utility is used with the cach e enabled and Administrator mode was timed out, the timeout page may appear even when PageScope Web Connection is accessed aga in. ...

  • Konica Minolta 181 - page 285

    11 Using PageScope Web Connection 11-8 IC-206 11.6 Logging on to Administrator mode Some parameters in PageScope Web Co nnection should only be specified by the administrator. These parameters do not appear unless you are logged on to Administrator mode. To log on to Admini strator mode 1 In the “Admin Password” box on the le ft side of the pag ...

  • Konica Minolta 181 - page 286

    Using PageScope Web Connection 11 IC-206 11-9 2 Click the [Login] button. The Administrator mode page appears. To log off, click the [Logout] button. 2 Reminder The default password for logging on to Administrator mode is “sysadm”. We recommend that the admini strator password be changed. This machine cannot be used while a user is logged on to ...

  • Konica Minolta 181 - page 287

    11 Using PageScope Web Connection 11-10 IC-206 11.7 User mode The User mode provides functions for checking and oper ating the machine on a user level. This section contains descriptions of the items in the menu that appears on the left s ide of the pa ge when each User mode tab is clicked. User mode tabs You can select from five tabs (System, Job, ...

  • Konica Minolta 181 - page 288

    Using PageScope Web Connection 11 IC-206 11-11 System tab — Summary The system configuration and status of th e machine are displayed. This is the first page that appears when PageSc ope Web Connection is accessed with the Web browser. ...

  • Konica Minolta 181 - page 289

    11 Using PageScope Web Connection 11-12 IC-206 System tab — Details — Input Tray The name of each in stalle d paper drawer, the size an d type of the loaded pa- per, the printing orientation, the pape r drawer capacities, an d the status of the paper drawers are displayed. 2 Note The information that is displayed differs depending on the instal ...

  • Konica Minolta 181 - page 290

    Using PageScope Web Connection 11 IC-206 11-13 System tab — Details — Output Tray The name of each in stalled output tray, the tray capacities, and the status of the output trays are displayed. 2 Note The information that is displayed differs depending on the installed options and the specified settings. ...

  • Konica Minolta 181 - page 291

    11 Using PageScope Web Connection 11-14 IC-206 System tab — Details — ROM Version The name of each installed controller and their ROM version are displayed. 2 Note The information that is displayed differs depending on the installed options and the specified settings. ...

  • Konica Minolta 181 - page 292

    Using PageScope Web Connection 11 IC-206 11-15 System tab — Details — Interface Information The name of each installed i nterface and their information are displayed. 2 Note The information that is displayed di ffers depending on the installed op- tions and the specified settings. ...

  • Konica Minolta 181 - page 293

    11 Using PageScope Web Connection 11-16 IC-206 System tab — Details — Consumable Information about the machine consumable s is displayed. 2 Note The information that is displayed differs depending on the installed options and the specified settings. ...

  • Konica Minolta 181 - page 294

    Using PageScope Web Connection 11 IC-206 11-17 System tab — Maintenance — Counter Counters managed by the ma chine can be displayed. 2 Note The information that is displayed differs depending on the installed options and the specified settings. ...

  • Konica Minolta 181 - page 295

    11 Using PageScope Web Connection 11-18 IC-206 System tab — Online Assistance Support information for the machine can be displayed. The information entered on the page that appeared af ter clicking “Online As- sistance” in the menu on the System ta b in Administrator mode is displayed. ...

  • Konica Minolta 181 - page 296

    Using PageScope Web Connection 11 IC-206 11-19 Job tab — Print Job Manag ement Detailed information of th e print jobs are displayed. 2 Reminder A maximum o f 20 print j obs can be di splayed, and jobs that have been printed will automati cally be deleted. Jobs specified as secure print jobs are not displayed. 2 Note The number assign ed to the j ...

  • Konica Minolta 181 - page 297

    11 Using PageScope Web Connection 11-20 IC-206 Job tab — File Do wnload A specified file can be downloaded to this machine to be printed. 1 Click the [Browse] button, and then select the file. 2 Click the [Send] button. The file is downloaded to this machine, then printed. 2 Reminder Downloading the file is possible only if image controller IC-20 ...

  • Konica Minolta 181 - page 298

    Using PageScope Web Connection 11 IC-206 11-21 Print tab — Settings — Paper Handling Printer output settings can be viewed. A print job sent with no settings specified is pri nted with these s ettings. 2 Note The Print tab appears only if the image controller IC-206 is installed. Item Descript ion Copies Displays the specified number of copies. ...

  • Konica Minolta 181 - page 299

    11 Using PageScope Web Connection 11-22 IC-206 Print tab — Settings — Page Layout The paper size specified for the printer output paper size can be viewed. A print job sent with no settings spec ifi ed is printed with these settings. 2 Note The Print tab appears only if the image controller IC-206 is installed. ...

  • Konica Minolta 181 - page 300

    Using PageScope Web Connection 11 IC-206 11-23 Print tab — Settings — Printer Setting The settings related to the printer PCL functio n can be viewed. A print job sent with no settings specified is pri nted with these s ettings. 2 Note The Print tab appears only if the image controller IC-206 is installed. Item Descript ion Orientation Displays ...

  • Konica Minolta 181 - page 301

    11 Using PageScope Web Connection 11-24 IC-206 Print tab — Test Print The following test pages can be printed. - Configuration Page - PCL Font List 1 Click “Test Print” in t he menu on the Print tab. 2 Select the test page that you wish to print. 3 Click the [Print] bu tton. The selected test page is printed. 2 Note The Print tab appears only ...

  • Konica Minolta 181 - page 302

    Using PageScope Web Connection 11 IC-206 11-25 Print tab — Font Information The PCL font list can be checked. 2 Note The Print tab appears only if the image controller IC-206 is installed. ...

  • Konica Minolta 181 - page 303

    11 Using PageScope Web Connection 11-26 IC-206 Scan tab — One-Touch Dial Setting Registered one-touch dial settings can be viewed . 2 Reminder “One-Touch Dial Settin g” appears in the me nu only if fax ki t FK-506 is in- stalled. ...

  • Konica Minolta 181 - page 304

    Using PageScope Web Connection 11 IC-206 11-27 Scan tab — Speed Dial Setting Registered speed dial settings can be viewed. ...

  • Konica Minolta 181 - page 305

    11 Using PageScope Web Connection 11-28 IC-206 Scan tab — Group Dial Setting Registered group dial settings can be viewed. 2 Reminder “Group Dial Setting” appears in the me nu only if fax kit FK-506 is in- stalled. ...

  • Konica Minolta 181 - page 306

    Using PageScope Web Connection 11 IC-206 11-29 Network tab — Summary The basic network settings can be viewed. ...

  • Konica Minolta 181 - page 307

    11 Using PageScope Web Connection 11-30 IC-206 11.8 Administrator mode The Administrator mode provides functi ons for checking a nd operating the machine and ch anging settings on an administrator level. This section con - tains descriptions of the items in the me nu that appears on the left side of the page when each Ad ministra tor mode tab is cl ...

  • Konica Minolta 181 - page 308

    Using PageScope Web Connection 11 IC-206 11-31 System tab — Summary A summary of the system configuration fo r the machine and its status is dis- played. ...

  • Konica Minolta 181 - page 309

    11 Using PageScope Web Connection 11-32 IC-206 System tab — Details Information on the paper drawers, output trays, ROM version, interface and consumables can be vi ewed. The information that is displayed is the same as that displayed in User mode. 2 Note The information that is displayed differs depending on the installed options and the specifi ...

  • Konica Minolta 181 - page 310

    Using PageScope Web Connection 11 IC-206 11-33 System tab — Preference Information for managing PageScope Web Connection can be view ed and changed. To change the settings, sp ecify the various settings, and then click the [Ap- ply] button. 2 Reminder Be sure to keep the administrator password in a safe place. If the administrator password is los ...

  • Konica Minolta 181 - page 311

    11 Using PageScope Web Connection 11-34 IC-206 System tab — Save Setti ng PageScope Web Connection setti ng s can be saved and restored. ...

  • Konica Minolta 181 - page 312

    Using PageScope Web Connection 11 IC-206 11-35 Save Setting The current PageScope Web Connec tion settings can be saved. This can be used t o back up the setti ngs. 1 Specify settings for the various param eters that appear after clicking each menu item on each ta b of Administrator mode. 2 Click “Save Setting” in the menu on the System tab. 3 ...

  • Konica Minolta 181 - page 313

    11 Using PageScope Web Connection 11-36 IC-206 System tab — Maintenance — NIC and Printer Controller Reset The network interface card and im age controller can be restarted. 1 Click the [Reset] button. 2 When the confirmation message appears, click th e [Yes] button. To stop resetting, click the [No] button. 2 Reminder Jobs being processed are ...

  • Konica Minolta 181 - page 314

    Using PageScope Web Connection 11 IC-206 11-37 System tab — Maintenance — Initialize The firmware for the network interfac e card and image controller can b e up- dated or reset to the default. Firmware Update The firmware for the network interfac e card and image controller can b e up- dated. Contact your technical representative f or update f ...

  • Konica Minolta 181 - page 315

    11 Using PageScope Web Connection 11-38 IC-206 Restore Factory Defaults The network interface card and imag e controller can be initialized. 1 Click the [Restore] button beside eith er “Printer Controller” or “NIC”. 2 When the confirmation message appears, click th e [Yes] button. To stop initializing, click the [No] button. 2 Reminder Jobs ...

  • Konica Minolta 181 - page 316

    Using PageScope Web Connection 11 IC-206 11-39 System tab — Online Assistance Specify the support information for th e machine. This information is dis- played in the page that appears after clic king “Online Assistance” on the System tab in User mode. To change the settings, sp ecify the various settings, and then click the [Ap- ply] button. ...

  • Konica Minolta 181 - page 317

    11 Using PageScope Web Connection 11-40 IC-206 Job tab — Print Job Manag ement Detailed information of the print jobs can be displayed, and jobs can be de- leted. 2 Reminder A maximum of 20 print job s can be di splayed, and jobs that have been printed will automa tically be deleted. Jobs specified as secure print jobs are not displayed. 2 Note T ...

  • Konica Minolta 181 - page 318

    Using PageScope Web Connection 11 IC-206 11-41 Print tab — Settings — Paper Handling Printer output settings can be specified. A print job sent with no settings specified is pri nted with these s ettings. To change the settings, sp ecify the various settings, and then click the [Ap- ply] button. 2 Note The Print tab appears only if the image co ...

  • Konica Minolta 181 - page 319

    11 Using PageScope Web Connection 11-42 IC-206 Print tab — Settings — Page Layout The printer output paper size can be specified. A print job sent with no settings spec ifi ed is printed with these settings. To change the settings, sp ecify the various settings, and then click the [Ap- ply] button. 2 Note The Print tab appears only if the image ...

  • Konica Minolta 181 - page 320

    Using PageScope Web Connection 11 IC-206 11-43 Print tab — Settings — Printer Setting The settings related to the print er PCL function c an be specified. A print job sent with no settings specified is pri nted with these s ettings. To change the settings, sp ecify the various settings, and then click the [Ap- ply] button. 2 Note The Print tab ...

  • Konica Minolta 181 - page 321

    11 Using PageScope Web Connection 11-44 IC-206 Print tab — Test Print A test page can be printed. The information that is displayed and the procedure for printing test pages are the same as in User mode. 2 Note The Print tab appears only if the image controller IC-206 is installed. ...

  • Konica Minolta 181 - page 322

    Using PageScope Web Connection 11 IC-206 11-45 Print tab — Font Information The PCL font list can be checked. The information that is displayed is the same as that displayed in User mode. 2 Note The Print tab appears only if the image controller IC-206 is installed. ...

  • Konica Minolta 181 - page 323

    11 Using PageScope Web Connection 11-46 IC-206 Scan tab — One-Touch Dial Setting One-touch dial settings can be view ed and registered. 2 Note “One-Touch Dial Settin g” appears in the me nu only if fax ki t FK-506 is in- stalled. Item Description No. Displays the on e-touch dial number (betwe en 01 and 3 2). Name Displays t he name of t he re ...

  • Konica Minolta 181 - page 324

    Using PageScope Web Connection 11 IC-206 11-47 Registering one-to uch dial settings Fax destinations, e-mail destinations, gr oup dialing, and e-mail destinations specified through LD AP searches can be registered with one-touch dia l numbers. 1 Click a one-touch di al number that has not yet been programmed with a recipient. The One-Touch Registra ...

  • Konica Minolta 181 - page 325

    11 Using PageScope Web Connection 11-48 IC-206 3 Select the LDAP server search conditions and type in th e characters to be searched for, and then click the [Apply] button . – From the Network tab, specify the settings for the connection to the LDAP server. – For the characters to be entered for the LDAP search, consult with the network adminis ...

  • Konica Minolta 181 - page 326

    Using PageScope Web Connection 11 IC-206 11-49 4 From the results of the LDAP server search, select the desired destina- tion, and then click the [Add] button. 5 Specify the various settings, and then click the [Apply] button. – The settings that appear differ depending on th e transmission method. ...

  • Konica Minolta 181 - page 327

    11 Using PageScope Web Connection 11-50 IC-206 Sample page: For a f ax destination 2 Note To view or change the settings regist ered with a one-tou ch dial number, click the one-touch dial number whose settings ar e to be changed. When “Fax” is selected: Item Description Destination Name Type in the name o f the recipient. The display name appe ...

  • Konica Minolta 181 - page 328

    Using PageScope Web Connection 11 IC-206 11-51 When “E-Mail” or “LDAP Search” is selected: 2 Note Settings for Internet faxing are app lied when a transmission is specified using the procedure for Internet fax transmissions. The settin gs are no t applied when a transmission is specif ied using the proced ure for Scan to E-mail transmission ...

  • Konica Minolta 181 - page 329

    11 Using PageScope Web Connection 11-52 IC-206 Scan tab — Speed Dial Setting Speed dial settings can be viewed an d registered. Item Description No. Displays the speed dial number (between 001 and 240). Name Displays th e name of the reci pient registered with the spee d dial number. The display name appears in the control panel display. Address ...

  • Konica Minolta 181 - page 330

    Using PageScope Web Connection 11 IC-206 11-53 Registering speed dial settings Fax destinations, e-mail destinations, e-mail destinations specified through LDAP searches, and FTP server addresses can be registered with speed dial numbers. Transmission addresses an d FTP addresses can be registered with speed dial numbers. Register transmission addr ...

  • Konica Minolta 181 - page 331

    11 Using PageScope Web Connection 11-54 IC-206 3 Select the LDAP server search conditions and type in th e characters to be searched for, and then click the [Apply] button . – From the Network tab, specify the settings for the connection to the LDAP server. – For the characters to be entered for the LDAP search, consult with the network adminis ...

  • Konica Minolta 181 - page 332

    Using PageScope Web Connection 11 IC-206 11-55 5 Specify the various settings, and then click the [Apply] button. – The settings that appear differ depending on th e transmission method. Sample page: For an e-mail destination 2 Reminder “Fax” can be selected only whe n fax kit FK-506 is inst alled on the ma- chine. 2 Note To view or change th ...

  • Konica Minolta 181 - page 333

    11 Using PageScope Web Connection 11-56 IC-206 When “E-Mail” or “LDAP Search” is selected: 2 Reminder “Internet Fax Setting” is available only when fax kit FK-506 is in stalled on the machine. 2 Note Settings for Internet faxin g are applied when a transmission is specified using the procedure for Internet fax transmissions. The setting ...

  • Konica Minolta 181 - page 334

    Using PageScope Web Connection 11 IC-206 11-57 When “FTP Server Address” is selected: Item Descript ion Destination Name Type in the name of the recipient. The display name appea rs in the control panel display. FTP Server Ad- dress Specify the IP addres s or the host name of the FTP site wh ere the scan data will be sen t. (maximum 64 characte ...

  • Konica Minolta 181 - page 335

    11 Using PageScope Web Connection 11-58 IC-206 Scan tab — Group Dial Setting Group dial settings can be viewed and registere d. 2 Reminder “Group Dial Setting” appears in the me nu only if fax kit FK-506 is in- stalled. Item Description No. Displays the group dial number (between 01 and 32). Name Displays the name of the recipient regis tered ...

  • Konica Minolta 181 - page 336

    Using PageScope Web Connection 11 IC-206 11-59 Registering group dial set tings With group dialing, multip le recipients from regis t ered one-touch dial desti- nations and speed dial destinations ca n be registered together as a group. The group dial destinations are regi stered as a single one-tou ch dial number. 1 Click a group dial number that ...

  • Konica Minolta 181 - page 337

    11 Using PageScope Web Connection 11-60 IC-206 2 Note FTP server addresses cannot be registered as a group. To view or change the settings register ed with a group di al number, click the group dial number whose settings are to be changed. ...

  • Konica Minolta 181 - page 338

    Using PageScope Web Connection 11 IC-206 11-61 Scan tab — Fax Confi guration User information and transmission cond itions for fa xes can be viewed and registered. ...

  • Konica Minolta 181 - page 339

    11 Using PageScope Web Connection 11-62 IC-206 Item Description User Name Type in the name of the sender. Fax Nmber Type in the fax number of the sender. Scan Contrast Select the scanning densit y. Image Quality Select the image quality. Default TX Select the transmission mode given priority. Header Selec t whether or not the he ader is added. Memo ...

  • Konica Minolta 181 - page 340

    Using PageScope Web Connection 11 IC-206 11-63 2 Reminder “Fax Configuration” appears in the menu only if fax kit FK-506 is installed. Scan tab — Downloading/Up loading Destination Li st The specified one-touch dial and spee d dial settings can be saved and re- stored. Download The specified one-touch dial and speed dial settings can be saved ...

  • Konica Minolta 181 - page 341

    11 Using PageScope Web Connection 11-64 IC-206 Upload The one-touch dial and speed dial settings can b e changed to those saved in the file using the procedu re described in “Download”. 1 Click the [Browse] button, and then select the file to be uploaded. 2 Click the [Apply] button. The one-touch dial and speed dial settings are changed to thos ...

  • Konica Minolta 181 - page 342

    Using PageScope Web Connection 11 IC-206 11-65 Network tab — TCP/IP Co nfiguration Specify the TCP/IP infor mation for the network. To change the settings, sp ecify the various settings, and then click the [Ap- ply] button. Item Descript ion IP Address Specify the IP address of the machine. Subnet Mask Specify the subne t mask of the connected ne ...

  • Konica Minolta 181 - page 343

    11 Using PageScope Web Connection 11-66 IC-206 2 Reminder To change the settings on the Network tab, click th e [Apply] button, and then, after “Upda ted Successful” a ppear s, click the [Reset ] button on the page that appears aft er clicking “NIC and P rinter Controller Reset” in the menu under “Maintenan ce” on the System tab; otherw ...

  • Konica Minolta 181 - page 344

    Using PageScope Web Connection 11 IC-206 11-67 2 Reminder To change the settings on the Network tab, click the [A pply] button, and then, after “Upda ted Successful ” appear s, click the [Reset ] button on the page that appears after clicking “NIC and Printer Controller Reset” in the menu under “Maintenan ce” on the System tab; otherwis ...

  • Konica Minolta 181 - page 345

    11 Using PageScope Web Connection 11-68 IC-206 Network tab — NetWare Conf iguratio n — Ne tWare Status The server and print queue name are displaye d to show the NetWare con- nection status. Preferred NDS T ree Name of the tree whe re Pserver logs on Not necessary to specify Name of the tree whe re Pserver logs on Not necessary to specify Print ...

  • Konica Minolta 181 - page 346

    Using PageScope Web Connection 11 IC-206 11-69 Network tab — IPP Configurati on To change the settings, sp ecify the various settings, and then click the [Ap- ply] button. Item Descript ion Enable IPP Select whether or not IPP printing is enabled. Printer Name Type in the printer name. (maximum 127 characters) Printer Loca tion Type in the print ...

  • Konica Minolta 181 - page 347

    11 Using PageScope Web Connection 11-70 IC-206 2 Reminder To change the settings on the Network tab, click th e [Apply] button, and then, after “Upda ted Successful” a ppear s, click the [Reset ] button on the page that appears aft er clicking “NIC and P rinter Controller Reset” in the menu under “Maintenan ce” on the System tab; otherw ...

  • Konica Minolta 181 - page 348

    Using PageScope Web Connection 11 IC-206 11-71 Network tab — SMTP & POP3 Configuration Specify the SMTP and POP3 information for e-mail transmission/reception. To change the settings, sp ecify the various settings, and then click the [Ap- ply] button. Item Descript ion Enable PO P before SMTP Select whether or not POP before SMTP is us e d. I ...

  • Konica Minolta 181 - page 349

    11 Using PageScope Web Connection 11-72 IC-206 Sender name Specify the sender name used when sending scan da ta attached to an e- mail message. (maxim um 20 characters) E-Mail Address Spe cify the e-mail address of the sender. (maximum 64 characters) Port Number Specify the port number ( between 1 and 65535) of the SMTP s erver. Nor- mally, port nu ...

  • Konica Minolta 181 - page 350

    Using PageScope Web Connection 11 IC-206 11-73 2 Reminder “Auto Reception”, “INTERVAL”, “Reply Address”, “Header Print” and the settings below “Internet Fax Setting” appear in the page only if fax kit FK- 506 is instal led. To change the settings on the Network tab, click the [A pply] button, and then, after “Upda ted Successf ...

  • Konica Minolta 181 - page 351

    11 Using PageScope Web Connection 11-74 IC-206 2 Reminder To change the settings on the Network tab, click th e [Apply] button, and then, after “Upda ted Successful” a ppear s, click the [Reset ] button on the page that appears aft er clicking “NIC and P rinter Controller Reset” in the menu under “Maintenan ce” on the System tab; otherw ...

  • Konica Minolta 181 - page 352

    Using PageScope Web Connection 11 IC-206 11-75 2 Reminder To change the settings on the Network tab, click the [A pply] button, and then, after “Upda ted Successful ” appear s, click the [Reset ] button on the page that appears after clicking “NIC and Printer Controller Reset” in the menu under “Maintenan ce” on the System tab; otherwis ...

  • Konica Minolta 181 - page 353

    11 Using PageScope Web Connection 11-76 IC-206 ...

  • Konica Minolta 181 - page 354

    Troubleshooting 12 IC-206 12-1 12 Troubleshooting This chapter provides details on the causes for error messages to appear and the various operations to correct the problem. 12.1 Main error messages and their remedies Message Cause Remedy COMMUNICATION ERROR XXXX server Communication with the serv- er is not possible becau se of some problem in the ...

  • Konica Minolta 181 - page 355

    12 Troubleshooting 12-2 IC-206 If a printing error occurs, the “Caution ” indicator lights up and the message “Check Printer Mode” appears in the ma chine’s display. In this case, press the [Printer] key to displa y the Printer mode screen. The main error messages th at appear in the Printer mode screen are de- scribed below. Error messag ...

  • Konica Minolta 181 - page 356

    Troubleshooting 12 IC-206 12-3 12.2 Troubleshooting Network printing If network printing cannot be perf ormed, check for the following. Scan to E-mail Problem Cause Remedy 1 Did the machine re - ceive the print job? Yes A machine error (out of pa- per, out of toner, etc. ) oc- curred. Check the machin e status and correct the error. No The data has ...

  • Konica Minolta 181 - page 357

    12 Troubleshooting 12-4 IC-206 PageScope Web Connection Transmission is pos- sible, but the imag e cannot be outputt ed at the recipie nt’s ter- minal or co mputer. The recipient’s terminal is not able to handle the sent image. Change the siz e, resolution and compre ssion encoding method so that they are supported by the recipi- ent’s ter mi ...

  • Konica Minolta 181 - page 358

    Troubleshooting 12 IC-206 12-5 Some deleted char- acters remain i n the window. The operation diffe rs de- pending on the browser used. Reload the browser win- dow or rescan. — The number of digits in an input or display area and the num ber of characters that can be register ed are different. Depending on the browser, scroll within the input are ...

  • Konica Minolta 181 - page 359

    12 Troubleshooting 12-6 IC-206 12.3 Print data wh en an error occurs The operation performed with the print da ta when an error occurs differs de- pending on the type of error that occurred. With a “MACHINE TROUBLE” error This error indicates that a severe oper ating malfunction occurred. When this error message appears in the display, the mach ...

  • Konica Minolta 181 - page 360

    Appendix 13 IC-206 13-1 13 Appendix 13.1 Main product specifications Printing *1 The print speed is measured unde r the following printing condition s. Paper is fed from Tray 1. *2 AutoIP (APIPA (automatic private IP addre ssing)) is a function for automat- ically assigning to the networ k interface card an IP address beginn ing with 169.254 and su ...

  • Konica Minolta 181 - page 361

    13 Appendix 13-2 IC-206 Scan to E-mail/Scan to Server (FTP) Communication proto- col E-mail transmission: SMTP, TCP/IP FTP transmission: FTP, TCP/IP Resolution 150 × 150 dpi, 300 × 300 dpi, 600 × 600 dpi Data format E-mail format: MIME Attached file format: TIFF, PDF Compression encoding method MH, MR, M MR Network Ethernet LAN (10BASE-T and 100 ...

  • Konica Minolta 181 - page 362

    Copyright 2007 2007.12 A08E-9582-22 P/N:34364C016H031 http://konicaminolta.com Printed in China ...

Manufacturer Konica Minolta Category Network Card

Documents that we receive from a manufacturer of a Konica Minolta 181 can be divided into several groups. They are, among others:
- Konica Minolta technical drawings
- 181 manuals
- Konica Minolta product data sheets
- information booklets
- or energy labels Konica Minolta 181
All of them are important, but the most important information from the point of view of use of the device are in the user manual Konica Minolta 181.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Konica Minolta 181, service manual, brief instructions and user manuals Konica Minolta 181. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Konica Minolta 181.

A complete manual for the device Konica Minolta 181, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Konica Minolta 181 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Konica Minolta 181.

A complete Konica Minolta manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Konica Minolta 181 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Konica Minolta 181, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Konica Minolta 181, that we can find in the current document
3. Tips how to use the basic functions of the device Konica Minolta 181 - which should help us in our first steps of using Konica Minolta 181
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Konica Minolta 181
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Konica Minolta 181 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Konica Minolta 181?

Use the form below

If you did not solve your problem by using a manual Konica Minolta 181, ask a question using the form below. If a user had a similar problem with Konica Minolta 181 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)