English dropdown-ico

Manual Delta Electronics 0.75-3.3V

17 pages 0.85 mb
Download

Go to site of 17

Summary
  • Delta Electronics 0.75-3.3V - page 1

    DATASHEET DS_DNM04SMD10_07 162008 FEATURES  High efficiency: 96%@5.0V in, 3.3V/10A out  Small size and low profile: (SMD) 33.0x 13.5x8.8mm (1.30” x 0.5 3” x 0.35”)  Surface mount packaging  S tandard footprint  V olt age and resistor-based trim  Pre-bias startup  Output voltage tracking  No minimum load required  Ou ...

  • Delta Electronics 0.75-3.3V - page 2

    DS_DNM04SMD10_07 162008 2 TECHNICAL SPECIFICA TIONS (T A = 25°C, airfl ow rate = 300 LFM, V in = 2.8Vdc and 5.5V dc, nominal V out unle ss otherwise noted.) P ARAMETER NOTES and CONDITIONS DNM04S0A0S10PFD Min. T yp. Max. Units ABSOLUTE MAXIMUM RA TINGS Input V oltage (Continuous) 0 5.8 Vdc T racking V oltage Vin,max Vdc Operating T emperature Refe ...

  • Delta Electronics 0.75-3.3V - page 3

    DS_DNM04SMD10_07 162008 3 ELECTRICAL CHARACTERISTICS CUR VES Figure 1: Converter Efficiency vs. Output C urrent (3.3V out) Figure 2: Converter Efficiency vs. Output Current (2.5V out) Figure 3: Converter Efficiency vs. Output C urrent (1.8V out) Figure 4: Converter Efficiency vs. Output Cu rrent (1.5V out) Figure 5: Converter Efficiency vs. Output ...

  • Delta Electronics 0.75-3.3V - page 4

    DS_DNM04SMD10_07 162008 4 ELECTRICAL CHARACTERISTICS CUR VES Figure 7: Output ripple & noise at 3.3V in, 2.5V/10A out Figure 8: Output ripple & noise at 3.3V in, 1.8V/10A out Figure 9: Output ripple & noise at 5V in, 3.3V/10A out Figure 10: Output ripple & noise at 5Vin, 1.8V/10A out Figure 1 1: T urn on delay time at 3.3Vin, 2.5V/1 ...

  • Delta Electronics 0.75-3.3V - page 5

    DS_DNM04SMD10_07 162008 5 ELECTRICAL CHARACTERISTICS CUR VES Figure 13: T urn on delay time at 5Vin, 3.3V/10A out Figure 14: T urn on delay time at 5Vin, 1.8V/10A out Figure 15: T urn on delay time at remote turn on 5Vin, 3.3V/16A out Figure 16: T urn on delay time at remote turn on 3.3Vin, 2. 5V/16A out Figure 17: T urn on delay time at remote tur ...

  • Delta Electronics 0.75-3.3V - page 6

    DS_DNM04SMD10_07 162008 6 ELECTRICAL CHARACTERISTICS CUR VES Figure 19: T ypical T r ansient Response to Step Load Change at 2.5A/ μ S from 100% to 50% of Io, max at 5Vin, 3.3V out (Cout = 1uF ceramic, 10 μ F T antalum) Figure 20: T ypical T r ansient Response to Step Load Change at 2.5A/ μ S from 50% to 100% of Io, max at 5Vin, 3.3V out (Cout = ...

  • Delta Electronics 0.75-3.3V - page 7

    DS_DNM04SMD10_07 162008 7 ELECTRICAL CHARACTERISTICS CUR VES Figure 25: T ypical T r ansient Response to Step Load Change at 2.5A/ μ S from 100% to 50% of Io, max at 3.3Vin,1.8V out (Cout=1uF ceramic, 10 μ F T antalum) Figure 26: T ypical T rans ient Response to Step Load Chan ge at 2.5A/ μ S from 50% to 100% of Io, max at 3.3Vin,1.8V out (Cout ...

  • Delta Electronics 0.75-3.3V - page 8

    DS_DNM04SMD10_07 162008 8 TEST CONFIGURA TIONS V I (+) V I (-) BATTERY 2 100uF Tantalum L TO OSCILLOSCOPE Note: Input reflected-ripple current is measured with a simulated sour ce inductance. Curr ent is measured at the input of the module. Figure 29: Input reflected-ripple test setup Vo GND COPPER STRIP 10uF tantalum 1uF ceramic SCOPE Resistive Lo ...

  • Delta Electronics 0.75-3.3V - page 9

    DS_DNM04SMD10_07 162008 9 DESIGN CONSIDERA TIONS (CON.) The power module sh ould be conne cted to a low ac-impedance input source. Highly in ductive source impedances can af fect the stability of the module. An input capacit ance must be placed close to the modules input pins to filter ripple current and ensure m odule stability in the presence o f ...

  • Delta Electronics 0.75-3.3V - page 10

    DS_DNM04SMD10_07 162008 10 FEA TURES DESCRIPTIONS (CON.) Over-T emperature Protection The over-temperature protection consists of circuitry that provides protection from thermal damag e. If the temperature exceeds the ove r-temperature thre shold the module will shut down. The module will try to restart after shutdown. If the over-temperature condi ...

  • Delta Electronics 0.75-3.3V - page 11

    DS_DNM04SMD10_07 162008 11 FEA TURE DESCRIPTIONS (CON.) The amount of power deliv ered by the module is the voltage at the output terminals multiplied by the output current. When using the tr im feature, the output volt age of the module can be in creased, which at the same output current would increase the power outp ut of the module. Care should ...

  • Delta Electronics 0.75-3.3V - page 12

    DS_DNM04SMD10_07 162008 12 FEA TURE DESCRIPTIONS (CON. ) Sequential St art-up Sequential st art-up (Figure 40) is imple mented by placing an On/Off co ntrol circuit between V o PS1 and the On/Off pin of PS2. Simultaneous Simultaneous tracking (Figure 4 1) is implemented by using the TRACK pin. The objective is to minimize the voltage dif ference be ...

  • Delta Electronics 0.75-3.3V - page 13

    DS_DNM04SMD10_07 162008 13 THERMAL CONSIDERA TIONS Thermal management is an importa nt part of the system design. To ensure prop er, reliable operation, suffici ent cooling of the power mod ule is needed over the entire temperature range of the modul e. Convection coolin g is usually the dominant mode of heat transfer. Hence, the choice of equipmen ...

  • Delta Electronics 0.75-3.3V - page 14

    DS_DNM04SMD10_07 162008 14 THERMAL CURVES Figure 44: T emperature measurement locati on * The allowed max imum hot spot temperature is defined at 125 ℃ DNM04S0A0S10(Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin = 5V, Vo = 3.3V (Either Orient ation) 0 2 4 6 8 10 12 60 65 70 75 80 85 Ambient Temperature ( ℃ ) Output Curr ...

  • Delta Electronics 0.75-3.3V - page 15

    DS_DNM04SMD10_07 162008 15 PICK AND PLACE LOCA TION SURF ACE-MOUNT T APE & REEL LEAD (Sn/Pb) PROCESS RE COMMEND TEMP . PROFILE Ti m e ( s e c . ) Pre-heat temp. 140~180 ° C 6 0~120 se c. Peak temp. 210~230 ° C 5sec. Ramp-up temp. 0.5~3.0 ° C /sec. T emperature ( ° C ) 50 100 150 200 250 300 60 0 120 180 240 2nd Ramp-up te mp. 1.0~3.0 ° C / ...

  • Delta Electronics 0.75-3.3V - page 16

    DS_DNM04SMD10_07 162008 16 MECHANICAL DRA WING SMD P ACKAGE SIP P ACKA GE ( OPTIONAL) ...

  • Delta Electronics 0.75-3.3V - page 17

    DS_DNM04SMD10_07 162008 17 P ART NUMBERING SYSTEM DNM 04 S 0A0 S 10 P F D Product Series Input V olt age Numb ers of Output s Output V oltage Package Ty p e Output Current On/Off logic Option Code DNL - 16A DNM - 10A DNS - 6A 04 - 2.8~5.5V 10 – 8.3~14V S - Single 0A0 - Programmable R - SIP S - SMD 16 -16A 10 -10A N- negative (Default) P- positive ...

Manufacturer Delta Electronics Category Power Supply

Documents that we receive from a manufacturer of a Delta Electronics 0.75-3.3V can be divided into several groups. They are, among others:
- Delta Electronics technical drawings
- 0.75-3.3V manuals
- Delta Electronics product data sheets
- information booklets
- or energy labels Delta Electronics 0.75-3.3V
All of them are important, but the most important information from the point of view of use of the device are in the user manual Delta Electronics 0.75-3.3V.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Delta Electronics 0.75-3.3V, service manual, brief instructions and user manuals Delta Electronics 0.75-3.3V. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Delta Electronics 0.75-3.3V.

Similar manuals

A complete manual for the device Delta Electronics 0.75-3.3V, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Delta Electronics 0.75-3.3V by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Delta Electronics 0.75-3.3V.

A complete Delta Electronics manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Delta Electronics 0.75-3.3V - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Delta Electronics 0.75-3.3V, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Delta Electronics 0.75-3.3V, that we can find in the current document
3. Tips how to use the basic functions of the device Delta Electronics 0.75-3.3V - which should help us in our first steps of using Delta Electronics 0.75-3.3V
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Delta Electronics 0.75-3.3V
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Delta Electronics 0.75-3.3V in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Delta Electronics 0.75-3.3V?

Use the form below

If you did not solve your problem by using a manual Delta Electronics 0.75-3.3V, ask a question using the form below. If a user had a similar problem with Delta Electronics 0.75-3.3V it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)