English dropdown-ico

Manual Jet JBG-6A

20 pages 1.48 mb
Download

Go to site of 20

Summary
  • Jet JBG-6A - page 1

    Operating Instructions and Parts Manual JBG Series Bench Grinders Models: JBG-6A, JBG-8A, JBG-10A Model JBG-8A shown WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-577101 Ph.: 800-274-6848 Revision G 04/06 www.wmhtoolgroup.com Copyright © WMH Tool Group This Manual is Bookmarked ...

  • Jet JBG-6A - page 2

    2 WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it se lls. If one of our tools nee ds service or repair, one of our Authorized Service Centers lo cated throughout the United States can giv e you qu ick service. In most cases, any of these WMH Tool Group Authorized Servic e Centers can authorize warranty repair, assist you in obt ...

  • Jet JBG-6A - page 3

    3 Table of Contents WARRANTY A ND SERVICE ........................................................................................................... ............. 2 Table of Contents .............................................................................................................. ............................ 3 Warnings ............... ...

  • Jet JBG-6A - page 4

    4 Warnings 1. For your own safety read instruct ion ma nual before operating grinder. 2. Read and understand the entire o wner’s manual bef ore attempting assembly or operation. 3. Read and understand the warnings posted on the m a chine and in this manual. Failure to comply with all of these warnings may cause seri ous injury. 4. Replace the war ...

  • Jet JBG-6A - page 5

    5 21. Make your workshop child proof with padlocks , mas ter switches or by removing starter keys. 22. KEEP WORK AREA CLEAN. Clutte red areas and benches invite accidents. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use po wer tools in damp or wet locations, or expo se them to rain. Keep work area well li ghted. Keep the floor arou nd the machine ...

  • Jet JBG-6A - page 6

    6 Introduction This manual is provided by WMH Tool Grou p covering the safe operation and maintenance procedures for the JET JBG Series Ben ch Grinders. This manual contains instructions on in stallation, safety precautions, general o perating procedures, mainten ance instructio ns and parts brea kdown. This machine has been designed and constru ct ...

  • Jet JBG-6A - page 7

    7 Unpacking Separate all parts from the packin g material. Check each part against the Contents of the Shipping Container and make ce rtain that all items are accoun ted for before discarding a ny packing material. Contents of the Shipping Container 1 Bench Grinder (not shown) 1 Hardware (contents listed below) Hardware 1 ea Bracket - Left ( A ) 2 ...

  • Jet JBG-6A - page 8

    8 Assembly Your bench grinder requires only the assembly of the eye shields and tool rests. F or your safety, do not plug the grinder into a power sou rce until all adjustments are complete. An adjusta ble wrench and a Phillips screwdriver are the only tools you will need to make all normal adjustments and wheel changes on this gri nder. Be sure th ...

  • Jet JBG-6A - page 9

    9 Installing the Spark Guard and Eye Shield Mounting Brackets Refer to Figure 2: Parts needed: 2 Spark Guard and Eye Shield Brackets assembled from previous page 4 1/4” x 3/8” Hex Cap Screws (E) 4 1/4" Flat Washers (F) 1. Install the left spark guard and mounting bracket (A) to the l eft wheel housin g (M) with two 1/4” x 3/8” hex cap ...

  • Jet JBG-6A - page 10

    10 Electrical Electrical Requirements When connecting the bench grinde r to the power source outlet, the outlet must be properly grounded to protect the operator from electrical shock. In the event of a malfunction or br eakdown, grounding provides a path of least resistance fo r electrical current to reduce the risk of electrical shock. This machi ...

  • Jet JBG-6A - page 11

    11 Operation A bench grinder is designed for ha nd-grinding operations such as sharpening chisels, screwdrivers, drill bits, removing excess metal, and smoothing metal surface s. A Medium Grain Abrasive G rinding Wheel is suitable for rough grinding where a co nsiderable amount of metal must be removed or whe n obtaining a smooth finish is not impo ...

  • Jet JBG-6A - page 12

    12 Maintenance For safety, turn the switch to OFF and remove plug from the power source outlet before adjusting and maintaining the bench grinder. If the power cord is worn, cut or damage d in any way, have it replaced immediately. Ring Test Before replacing a grindi ng wheel, perform thi s simple test on the replacement wheel: 1. Loop a piece of s ...

  • Jet JBG-6A - page 13

    13 Grinding Wheels The JET Series bench grinders co me equipped with general purpose gri nding wheels. Wheels vary according to types of abrasive, hardness, grit size, and structure. JET carries a full line of abrasive grinding, carbide grindi ng, tool sharpening, and wire whee ls. Contact your local distributor for the proper grinding wh eel or wi ...

  • Jet JBG-6A - page 14

    14 Troubleshooting Problem Probable Cause Remedy Not plugged into receptacle Plug it into the power source receptacle Switch not in the ON position Turn the switch to the ON positio n Motor cord cut or abraded Replace with a new cord Plug on cord is faulty Replace with a new plug Fuse or circuit breaker ope n Re-set, may be too many machines on lin ...

  • Jet JBG-6A - page 15

    15 Parts and Assembly Parts List Index No Part No Description Size Qty 1 ............... JBG6A-02P .............. Sha ft and Rot or Assy ........................................... ......................... ........... 1 ................. JBG8A-02P .............. Shaft and Rotor Assy ........................................... ..................... ...

  • Jet JBG-6A - page 16

    16 Parts List Index No Part No Description Size Qty 27 ............. JBG6A-27 ................ Tool Rest - left ...................................................... .................. .................. 1 ................. JBG8A-27 ................ Tool Res t - left ...................................................... ................ ......... ...

  • Jet JBG-6A - page 17

    17 Parts List Index No Part No Description Size Qty 54A ........... JBG6A-54 ................ Cross Screw ......................................................... 1/4x3/8 .............. .......... 4 55 ............. JBG6A-55 ................ Eye Shie ld Plate - left........................................... ...................... .............. 1 ...

  • Jet JBG-6A - page 18

    18 Assembly Drawing ...

  • Jet JBG-6A - page 19

    19 Wiring Diagram ...

  • Jet JBG-6A - page 20

    20 Replacement Parts Replacement parts are listed on the following page s. To order parts or reach our se rvice department, call 800-274-6848 between 7 :30 a.m. and 5:30 p.m. (CST), Monday through Friday. Having the Model Number and Serial Number of your machine availabl e when you cal l will allow us to serve you quickly and accurately. WMH Tool G ...

Manufacturer Jet Category Grinder

Documents that we receive from a manufacturer of a Jet JBG-6A can be divided into several groups. They are, among others:
- Jet technical drawings
- JBG-6A manuals
- Jet product data sheets
- information booklets
- or energy labels Jet JBG-6A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Jet JBG-6A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Jet JBG-6A, service manual, brief instructions and user manuals Jet JBG-6A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Jet JBG-6A.

Similar manuals

A complete manual for the device Jet JBG-6A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Jet JBG-6A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Jet JBG-6A.

A complete Jet manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Jet JBG-6A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Jet JBG-6A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Jet JBG-6A, that we can find in the current document
3. Tips how to use the basic functions of the device Jet JBG-6A - which should help us in our first steps of using Jet JBG-6A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Jet JBG-6A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Jet JBG-6A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Jet JBG-6A?

Use the form below

If you did not solve your problem by using a manual Jet JBG-6A, ask a question using the form below. If a user had a similar problem with Jet JBG-6A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)