English dropdown-ico

Manual Agilent Technologies 66000A

26 pages 0.23 mb
Download

Go to site of 26

Summary
  • Agilent Technologies 66000A - page 1

    INSTALLATION GUIDE Agilent Technologies MPS Mainframe Model 66000A SERIAL NUMBERS For mainframe with serial numbers: Agilent Model 66000A: 3138A-00101 and above * For instruments with higher Serial Numbers, a change page may be included. Agilent Part No. 66000-90001 Printed in USA: June , 1997 Microfiche Part No. 66000-90002 Update April 2000 ...

  • Agilent Technologies 66000A - page 2

    2 CERTIFICATION Agilent Technologies certifies that this product met its published specifications at time of shipment from the factory. Agilent Technologies further certifies that its calibration measurements are traceable to the United States National Bureau of Standards, to the extent allowed by the Bureau’s calibration facility, and to the cal ...

  • Agilent Technologies 66000A - page 3

    3 SAFETY SUMMARY The following general safety precautions must be observed during all phases of operation, service, and repair of this mainframe. Failure to com ply with these precautions or with specific warnings elsewhere in this guide violates safety standards of design, manufacture, and intended use of the mainfram e. Agilent Technologies assum ...

  • Agilent Technologies 66000A - page 4

    4 S AFETY S UMMARY (continued) GENERAL: Any LEDs used in this product are Class 1 LEDs as per IEC 825-1. ENVIRONMENTAL CONDITIONS: This instrument is intended for indoor use in an installation category II, pollution degree 2 environment. It is designed to operate at a maximum relative humidity of 95% and at altitudes of up to 2000 meters. Refer to ...

  • Agilent Technologies 66000A - page 5

    5 Printing History The current edition of this guide is indicated below. Reprints of this guide containing minor corrections and updates may have the same printing date. New editions are identified by a new printing date and, in some cases, by a new part number. A new edition incorporates all new or corrected material since the previous edition. Ch ...

  • Agilent Technologies 66000A - page 6

    6 Table Of Contents 1. General Information Introduction ................................................................................................................ .................................. 9 Safety Considerations ....................................................................................................... .................. ...

  • Agilent Technologies 66000A - page 7

    7 Figures 2-1. Power Cord Plug Configurations ............................................................................................ 1 4 2-2. Power Cord Installation .................................................................................................... ...... 15 2-3. Rear Panel Switches .......................................... ...

  • Agilent Technologies 66000A - page 8

    General Information 9 1 General Information Introduction This guide describes how to install the Agilent 66000A Modular Power System (MPS) Mainframe. It includes the following information: ■ specifications and operating characteristics ■ connecting the power cord to the mainframe ■ setting the address and frame switches ■ installing modules ...

  • Agilent Technologies 66000A - page 9

    General Information 10 Options and Parts The following options are available with the mainframe: Option Description 908 Rack Mounting Kit 909 Rack Mounting Kit with handles 910 Extra Manual Set Power Cords 831 12 AWG unterminated power cord 833 1.5 mm 2 unterminated power cord 834 10 AWG unterminated power cord 841 20 A/250 V NEMA 6-20P plug with 1 ...

  • Agilent Technologies 66000A - page 10

    General Information 11 Specifications and Supplemental Characteristics Table 1-1 lists the specifications an d supplemental characteristics of the MPS main fram e. Module specifications are included in the appr o priate module User’ s Guide. Specif ications are warran ted in the temperatu re range of 0 to 55 degrees C. Supplem ental characteristi ...

  • Agilent Technologies 66000A - page 11

    General Information 12 Table 1-1. Specifications and Supplemental Characteristics (continued) INH/FLT Characteristics Maximum Ratings: ± 16.5 V between pins 3 and 4 + 16.5 V between pins 1 and 2 - 5.3 V between pins 1 and 2 INH (10k pull-up): I I L @ 4 V = 700 µ A I IH @ 5.25 V = 200 µ A V I L = 0.8 V maximum V IH = 2.0 V minimum DFI (open colle ...

  • Agilent Technologies 66000A - page 12

    Installation 13 2 Installation Installation When you receive your mainframe, first look for any obvious damage that could have occurred during shipment. If there is damage, notify the carrier and the nearest Agilent Sales Office immediately. Warranty information is printed behind the cover page of this manual. Save the shipping carton and packing m ...

  • Agilent Technologies 66000A - page 13

    Installation 14 Fuses The mainframe fuse is located inside the mainframe. Refer to the mainframe Service Manual for information about replacing the fuse. Power Cord Installation The power cord supplied with your mainframe may or may not include a power plug. Figure 2-1 shows the various power plugs. Ring terminals are attached to one end of the pow ...

  • Agilent Technologies 66000A - page 14

    Installation 15 Figure 2-2. Power Cord Installation Location and Cooling Bench Operation Chapter 1 gives the dimensions of your mainframe. The mainframe has plastic feet that are shaped to ensure self-alignment when stacked with other Agilent System II cabinets. The feet may be removed for rack mounting. Your mainframe must be installed in a locati ...

  • Agilent Technologies 66000A - page 15

    Installation 16 Rear Panel Switches The six-position rear panel switch is shown in the following figure. Figure 2-3. Rear Panel Switches Address Switches Address switches A0 through A4 set the primary GPIB address. The address is set in binary, A0 being the least significant bit and A4 being the most significant bit. Figure 2-3 shows the factory-se ...

  • Agilent Technologies 66000A - page 16

    Installation 17 Mainframe Slot Locations/Addresses Mainframe Mode Switch = MAIN Mainframe Mode Switch = AUX Slot Location 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 Secondary Address 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Note Secondary addresses are reserved for the mainframe whether modules occupy the associated slot locations or not. You may want to apply s ...

  • Agilent Technologies 66000A - page 17

    Installation 18 Module Installation Note A f ully loaded m ainfram e can weigh over 36 kg (80 lbs). Install the m ainframe into th e rack before installing the modules into the mainf rame. All modules install through the front of the mainframe. Installation (and removal) can be accomplished even when the mainframe is rack-mounted. To install the mo ...

  • Agilent Technologies 66000A - page 18

    Installation 19 ■ There must be no or minimal current flowing through the connector pins at the back of the module that is being removed. This can be accomplished by disabling the module. If this precaution is repeatedly violated at high current, the connector pins at the back of the module will be damaged. ■ There must be no activity on the GP ...

  • Agilent Technologies 66000A - page 19

    Connections 21 3 Connections Rear Panel Figure 3-1 shows where all of the rear panel connections to the mainframe are made. Figure 3-1. Rear Panel Connections Module Connections Wire connections to the modules are made using a separate module connector that is supplied with each module. After the module connector has been wired, it simply attaches ...

  • Agilent Technologies 66000A - page 20

    Connections 22 Controller Connections If you have only one MPS mainframe in your system, simply connect it to the controller using the GPIB cable. If you have more than one mainframe, or if you also have an Agilent 667xA, 665xA, 664xA, or 603xA power supply in your system, you can use the serial-link cable supplied with your mainframe to facilitate ...

  • Agilent Technologies 66000A - page 21

    Connections 23 Figure 3-2. Controller Connections ...

  • Agilent Technologies 66000A - page 22

    Connections 24 Figure 3-3. Digital Connector FLT Output Used to indicate that a fault has occurred on one of the modules in the mainframe. Pins 1 and 2 (pins 1 and 2) are the open-collector output of an optocoupler, with pin 1 the collector and pin 2 the emitter. When a fault has occurred, pin 1 is driven low with respect to pin 2 (negative-true). ...

  • Agilent Technologies 66000A - page 23

    Connections 25 Figure 3-4. Examples of the Remote Inhibit Function ...

  • Agilent Technologies 66000A - page 24

    Index 27 Index AM addresses, 16 MAIN, 16, 22 address switch, 16 manuals, 9, 13 Agilent 603xA, 10, 11, 16, 22 module, 11, 21, 22 Agilent 664xA, 10, 11, 16, 22 module - addresses, 22 Agilent 665xA, 10, 11, 16, 22 module - connector, 21 Agilent 667xA, 10, 11, 16, 22 module - installation, 18 AUX, 16, 17, 22 module - removal, 18-19 modules, 11, 18 B BN ...

  • Agilent Technologies 66000A - page 25

    Agilent Sales and Support Offices For more information about Agilent Technologies test and measurement products, applications, services, and for a current sales office listing, visit our web site: http://www.agilent.com/find/tmdir You can also contact one of the following centers and ask for a test and measurement sales representative. United State ...

  • Agilent Technologies 66000A - page 26

    Manual Updates The following updates have been made to this manual since the print revision indicated on the title page. 4/15/00 All references to HP have been changed to Agilent. All references to HP-IB have been changed to GPIB. ...

Manufacturer Agilent Technologies Category Computer Hardware

Documents that we receive from a manufacturer of a Agilent Technologies 66000A can be divided into several groups. They are, among others:
- Agilent Technologies technical drawings
- 66000A manuals
- Agilent Technologies product data sheets
- information booklets
- or energy labels Agilent Technologies 66000A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Agilent Technologies 66000A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Agilent Technologies 66000A, service manual, brief instructions and user manuals Agilent Technologies 66000A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Agilent Technologies 66000A.

Similar manuals

A complete manual for the device Agilent Technologies 66000A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Agilent Technologies 66000A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Agilent Technologies 66000A.

A complete Agilent Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Agilent Technologies 66000A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Agilent Technologies 66000A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Agilent Technologies 66000A, that we can find in the current document
3. Tips how to use the basic functions of the device Agilent Technologies 66000A - which should help us in our first steps of using Agilent Technologies 66000A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Agilent Technologies 66000A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Agilent Technologies 66000A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Agilent Technologies 66000A?

Use the form below

If you did not solve your problem by using a manual Agilent Technologies 66000A, ask a question using the form below. If a user had a similar problem with Agilent Technologies 66000A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)