Manual DeWalt 28-682

20 pages 1.67 mb
Download

Go to site of 20

Summary
  • DeWalt 28-682 - page 1

    INSTRUCTION MANUAL 18" Band Saw (Model 28-682) P ART NO. 911988 - 07-28-04 Copyright © 2004 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...

  • DeWalt 28-682 - page 2

    2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop ...

  • DeWalt 28-682 - page 3

    3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • DeWalt 28-682 - page 4

    4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA ...

  • DeWalt 28-682 - page 5

    5 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SAFETY RULES FOR BAND SA WS SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed according to the instructions. 2. OBT AIN ADVICE fr om your supervisor, instructor , or ...

  • DeWalt 28-682 - page 6

    6 6 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before conn ...

  • DeWalt 28-682 - page 7

    7 3. Grounded, cor d-connected machines intended for use on a supply circuit having a nominal rating between 150 - 250 volts, inclusive: If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. C, the machine w ill have a g r ounding plug that looks like the plug illustrated in Fig. C. Make sure ...

  • DeWalt 28-682 - page 8

    8 FOREWORD Delta Model 28-682 is an 18" W ood Cutting Band Saw . This machine has speeds of 2300 and 3250 SFPM (surface feet per minute). Its blade to frame capacity is 17 1 / 2 " and its height under guide capacity is 12". The band saw has a quick blade tensioning mechanism for ease of changing blades. The Delta Model 28-682 has a l ...

  • DeWalt 28-682 - page 9

    Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be r emoved with a soft cloth moistened w it h k e r osene. (Do not us e acetone, gasoline or lacquer thinner for this purpose.) After cleaning, cover the unpainted surfaces with a good qualit ...

  • DeWalt 28-682 - page 10

    1. Remove the table pin (A) Fig. 5. 2. Align the blade with the table slot (B) Fig. 5. Slide the table until the blade has reached the center cutout (C) Fig. 5, then rotate the table 90 degr ees toward the fr ont of the machine. NOTE: Make sure that the table slot (B) Fig. 6 is facing towar d the right of the machine. 3. Align the two table studs ( ...

  • DeWalt 28-682 - page 11

    11 FENCE 1. Align the two holes (A) Fig. 9 in the front fence rail with the two holes (B) in the fr ont of the table. NOTE: Make sure that the scale on the fr ont fence rail is facing upward. 2. Insert a 1/4-20 x 1-1/2" socket-head cap screw thr ough one of the holes (A) Fig. 9 hole in the front fence rail. Place a spacer on the screw between ...

  • DeWalt 28-682 - page 12

    12 ST AR TING AND STOPPING SAW The power switch is located on the left side of the machine. T o tur n the machine “ON” , push the green start button (A) Fig. 14. T o tur n the machine “OFF” , push the red stop button (B). Fig. 14 LOCKING SWITCH IN THE “OFF” POSITION IMPORT ANT : When the tool is not in use, the switch should be locked i ...

  • DeWalt 28-682 - page 13

    13 4. Raise the blade tension lever to the “up” position and turn it clockwise to increase tension or counter - clockwise to relieve the tension. 5. After the first tur n, lower the blade tension lever and check the tension scale. If the tension is still not correct, r epeat the procedur e. The tension scale is correct for standar d blades used ...

  • DeWalt 28-682 - page 14

    The lower bearing adjustments are similar to the upper bearing adjustments. Adjust the blade support bearing (A) Fig 23 so that it is within 1/64” of, but not touching the back of the saw blade when the blade is at rest. T o adjust, loosen hex screw (B) and slide the bracket in or out until the adjustment is correct. Tighten the screw . Adjust th ...

  • DeWalt 28-682 - page 15

    15 Fig. 24 This machine is equipped with a positive stop that allows the table to be rapidly positioned at 90 degrees to the blade after the table has been tilted. T o check and adjust: 1. Place the table in the 90 degree position and lock it in place. 2. Place a square (A) Fig. 24 on the table with one end against the blade to check for 90 degrees ...

  • DeWalt 28-682 - page 16

    16 Fig. 28A ADJUSTING BEL T TENSION If it becomes necessary to adjust the belt tension on the machine, turn the motor release handle (A) Fig. 28A counter - clockwise. Lower or raise the motor , and when adjustment is complete, tighten the motor release handle (A). DUST CHUTE T wo dust chutes (A) Fig. 29 are supplied with your machine and can easily ...

  • DeWalt 28-682 - page 17

    17 BAND SAW BLADES A band saw blade is a delicate piece of steel that is subjected to tremendous strain. Y ou can obtain long use from a band saw blade if you use it properly . Be sure you use blades of the pr oper thickness, width and temper for the various types of material and cuts. Always use the widest blade possible. Use narrow blades only fo ...

  • DeWalt 28-682 - page 18

    18 T rouble: BAND SAW VIBRA TES EXCESSIVEL Y . Probable Cause Remedy 1. Machine not mounted securely to stand. 1. Tighten all mounting hardware. 2. Stand on uneven surface. 2. Reposition on flat level surface. 3. W orn belt. 3. Replace belt. 4. Pulley not aligned. 4. Adjust pulleys. 5. Motor not fastened securely . 5. Tighten all mounting hardware. ...

  • DeWalt 28-682 - page 19

    19 MAINTENANCE P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, se ...

  • DeWalt 28-682 - page 20

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Manufacturer DeWalt Category Saw

Documents that we receive from a manufacturer of a DeWalt 28-682 can be divided into several groups. They are, among others:
- DeWalt technical drawings
- 28-682 manuals
- DeWalt product data sheets
- information booklets
- or energy labels DeWalt 28-682
All of them are important, but the most important information from the point of view of use of the device are in the user manual DeWalt 28-682.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals DeWalt 28-682, service manual, brief instructions and user manuals DeWalt 28-682. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product DeWalt 28-682.

Similar manuals

A complete manual for the device DeWalt 28-682, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use DeWalt 28-682 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of DeWalt 28-682.

A complete DeWalt manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual DeWalt 28-682 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the DeWalt 28-682, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the DeWalt 28-682, that we can find in the current document
3. Tips how to use the basic functions of the device DeWalt 28-682 - which should help us in our first steps of using DeWalt 28-682
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with DeWalt 28-682
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of DeWalt 28-682 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning DeWalt 28-682?

Use the form below

If you did not solve your problem by using a manual DeWalt 28-682, ask a question using the form below. If a user had a similar problem with DeWalt 28-682 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)