English dropdown-ico

Manual Porter-Cable 750

19 pages 0.23 mb
Download

Go to site of 19

Summary
  • Porter-Cable 750 - page 1

    Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...

  • Porter-Cable 750 - page 2

    2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are ...

  • Porter-Cable 750 - page 3

    3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica from bricks and cement and other masonry pro ...

  • Porter-Cable 750 - page 4

    4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS 1) Work area safety a) Keep work a ...

  • Porter-Cable 750 - page 5

    5 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose ...

  • Porter-Cable 750 - page 6

    6 ADDITIONAL SPECIFIC SAFETY RULES 1. Hold power tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2. Use clamps or other practical way to secure and ...

  • Porter-Cable 750 - page 7

    7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litres g ........................ grams kg ........... ...

  • Porter-Cable 750 - page 8

    8 Length of Cord in Feet 115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft. 230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft. 0 - 2 1 8 1 8 1 8 1 6 1 61 4 1 41 2 1 2 2 - 3 1 8 1 8 1 6 1 4 1 41 2 1 21 0 1 0 3 - 4 1 8 1 8 1 6 1 4 1 21 2 1 01 0 8 4-5 18 18 14 12 12 10 10 8 8 5-6 18 16 14 12 10 10 8 8 ...

  • Porter-Cable 750 - page 9

    9 SELECTING THE BLADE For best performance, longer blade life, and smoother cut, select the proper blade for the job. When cutting metal always select a blade which will allow at least three teeth to be engaged in the thickness of material. INST ALLING THE BLADE with Keyless Quik-Change ™ Blade Clamp 1. The reciprocating shaft must be fully exten ...

  • Porter-Cable 750 - page 10

    10 If the blade breaks leaving nothing to grasp (to pull it from the clamp), it may be necessary to use another blade as a tool to aid in removing the broken piece (see Fig. 5). While holding the release collar in the open position, use the tip of another blade to “hook” the broken piece and pull it from the clamp. (A thin, fine-toothed, metal- ...

  • Porter-Cable 750 - page 11

    11 ROT A TABLE GEAR HOUSING ADJUSTMENT DISCONNECT TOOL FROM POWER SOURCE. 1. The variable angle reciprocating saw is designed with a rotatable gear housing for easy adjustment of cutting angle. This feature permits access to places where conventional tools cannot be used. 2. The gear housing can rotate 90° up or 90° down. The angle can be adjuste ...

  • Porter-Cable 750 - page 12

    12 PIVOTING GUIDE SHOE ADJUSTMENT with keyless Quik-Change ™ DISCONNECT TOOL FROM POWER SOURCE. DO NOT OPERATE THE TIGER SAW ® WITH THE GUIDE SHOE REMOVED. The Model 750 is supplied with a keyless Quik-Change ™ guide shoe. The pivoting guide shoe (A) Fig. 10, serves as a rest while making a cut and it can be adjusted to accommodate many types ...

  • Porter-Cable 750 - page 13

    13 HOW TO HOLD SAW The metal parts of the saw, blade and pivoting guide shoe may be made live if the blade cuts into live wiring within a wall. To prevent accidental electrical shock the tool must be held as shown in Fig. 13 or Fig.14, and have the rubber front housing cover properly installed and NOT DAMAGED . The rubber front housing cover also s ...

  • Porter-Cable 750 - page 14

    14 TO ST ART AND STOP SAW 1. Make sure swicth is off and power circuit voltage is the same as shown on the specification plate on the saw. Connect saw to power circuit. 2. Hold saw firmly (see Fig. 13 or Fig.14). Squeeze trigger switch (A) Fig. 15, to start motor. Release trigger to stop motor. V ARIABLE SPEED The saw is equipped with a variable sp ...

  • Porter-Cable 750 - page 15

    15 PLUNGE CUTS The variable angle reciprocating saw can be used for plunge cutting wood, plywood, wallboard, and plastic materials. DO NOT ATTEMPT TO PLUNGE CUT METAL. Clearly mark line of cut on the work. Grasp front housing with one hand and rear handle with the other hand. Choose a convenient starting point inside the line of cut in waste materi ...

  • Porter-Cable 750 - page 16

    16 For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers or call the Porter-Cable help line at 1-800-487-8665. TROUBLESHOOTING KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plasti ...

  • Porter-Cable 750 - page 17

    17 A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. Since accessories other than those offered by Porter-Cable • ...

  • Porter-Cable 750 - page 18

    18 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material du ...

  • Porter-Cable 750 - page 19

    The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...

Manufacturer Porter-Cable Category Cordless Saw

Documents that we receive from a manufacturer of a Porter-Cable 750 can be divided into several groups. They are, among others:
- Porter-Cable technical drawings
- 750 manuals
- Porter-Cable product data sheets
- information booklets
- or energy labels Porter-Cable 750
All of them are important, but the most important information from the point of view of use of the device are in the user manual Porter-Cable 750.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Porter-Cable 750, service manual, brief instructions and user manuals Porter-Cable 750. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Porter-Cable 750.

Similar manuals

A complete manual for the device Porter-Cable 750, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Porter-Cable 750 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Porter-Cable 750.

A complete Porter-Cable manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Porter-Cable 750 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Porter-Cable 750, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Porter-Cable 750, that we can find in the current document
3. Tips how to use the basic functions of the device Porter-Cable 750 - which should help us in our first steps of using Porter-Cable 750
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Porter-Cable 750
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Porter-Cable 750 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Porter-Cable 750?

Use the form below

If you did not solve your problem by using a manual Porter-Cable 750, ask a question using the form below. If a user had a similar problem with Porter-Cable 750 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)