Manual TP-Link WBS510

21 pages Not applicable
Download

Go to site of 21

Summary
  • TP-Link WBS510 - page 1

    I nstallation Guide Outdoor Wireless Base Station WBS210 / WBS510 C OPY RIGHT & TRADEMARKS is a register ed trademark of TP -LINK TECHNOLOGIES C O., L TD . Other brands and product names are trademarks or register ed trademarks of their respective holders. used to make any derivative such as translation, transformation, or adaptation without pe ...

  • TP-Link WBS510 - page 2

    C ontents Overview . Package Contents . Panel Layout Hardwar e Installation Connect cables Mount Antenna Power On Lightning and ESD Pr otection Specification FA Q 1 1 2 3 4 5 7 8 15 16 9 Config uration with P harOS Log in to the PharOS Configure the Base Station . Point-to-Point (PtP) . Point-to-Multipoint (PtMP) . Hotspot 9 12 14 11 11 ...

  • TP-Link WBS510 - page 3

    Overview TP-LINK's Outdoor Wireless Base Stations of the Phar os series products are designed f or outdoor wireless network solutions, aiming at long-distance transmission and large coverage of wireless network . The WBS210 and WBS510 are ideal for deployment in Point -to-Point (PtP) bridging, P oint-to-MultiPoint (PtMP) and Hotspot environmen ...

  • TP-Link WBS510 - page 4

    The panel of Base Station: Panel Layout RESET Shielded Ethernet Port LAN1 Shielded Ethernet Port LAN0(POE IN) Grounding Terminal 2 AP/AP Router mode: All four LEDs remain solid . Client/Bridge/Repeater/AP Client Router mode: The more lit LEDs indicate the better wireless sig nal strength. On: The port is connected but not ac tive. Flashing: The por ...

  • TP-Link WBS510 - page 5

    Passive PoE Adapter Hardw are Installation 3 The Outdoor Wireless Base Stations require external antenna that corresponds to your network environment; a dish antenna for Point-to-Point (PtP) bridge environment, a sector antenna for Point-to-MultiPoint (PtMP) environment, or a columnar antenna for Hotspot environment. Power LED: The Power LED indica ...

  • TP-Link WBS510 - page 6

    4 Affix the waterproof rubber insert to the underside of the device for waterproofing and replace the cover until it firmly locks into place. Use an adequate Ethernet cable (Lenth up to 60m) to connect the LAN0 (POE IN) port. Shielded CAT5e (or above) cable with an integrated ground wire is recommended. 2 Connect the RF Cables to the Base Station. ...

  • TP-Link WBS510 - page 7

    Attach the protective cap. Push and slide the protective cap down over the Base Station until it firmly locks into place. Align the mounting tabs on the back of the Base Station with the four slots of the mounting bracket. Push and slide the Base Station downward until it locks into place. Connect the RF cables from the Base Station to the correspo ...

  • TP-Link WBS510 - page 8

    6 Loosen and completely remove the end of the metal strap by turning the captive screw counterclockwise with a flathead screwdriver. Position the Base Station and wrap the metal strap around the pole. Feed the end back through the screw-block and turn the screw clockwise to tighten the metal strap using a flathead screwdriver until the Base Station ...

  • TP-Link WBS510 - page 9

    7 Connect the Ethernet cable from the Base Station to the POE port of the PoE adapter. Connect an Ethernet cable from your LAN device (a computer, router or switch) to the LAN port on the PoE adapter. Connect the power cord to the power port on the PoE adapter and plug it into an electrical outlet. Connect the Base Station to a Power over Ethernet ...

  • TP-Link WBS510 - page 10

    Lightning and ESD P rotection Use a shielded CAT5e (or above) cable with an integrated grounding wire for connection. If you have the standard CAT5e cable for the connection, use a separate grounding cable to connect the grounding Terminal (GND) to earth ground. Proper grounding is extremely important for outdoor devices. There are two effective te ...

  • TP-Link WBS510 - page 11

    Open a web browser, type http://192.168.0.254 into the address field and press Enter (Windows) or return (Mac). It is recommended to use the latest version of Google Chrome, Firefox or Safari. C onfiguration with PharOS Log in to the PharOS Before accessing the PharOS Web Interface, you need to assign a static IP address 192.168.0.X (X ranges betwe ...

  • TP-Link WBS510 - page 12

    Enter admin for both User Name and Password , then select your Region from the drop-down list. Read and agree the terms of use, then click Login . Change the default User Name and Password to protect your Base Station. Let’s start configuring the Base Staion. 10 3 4 For subsequent logins, use the new username and password. The Reliable Choice ...

  • TP-Link WBS510 - page 13

    1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Access Point and click Next . 3. LAN Settings: Click Next . 4. Wireless AP Settings: a. Create a new SSID (Network name) for your wireless network. b. Select WPA-PSK/WPA2-PSK for the Security method and create a PSK Password to protect your AP. c. Enter the distance betwe ...

  • TP-Link WBS510 - page 14

    Point to MultiPoint (PtMP) Configure the Client 12 AP Client Router LAN:192.168.0.254 WAN:Dynamic IP AP Client Router LAN:192.168.0.254 WAN:Dynamic IP AP Client Router LAN:192.168.0.254 WAN:Dynamic IP 1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Client and click Next . 3. LAN Settings: Change the IP Address to 192.1 ...

  • TP-Link WBS510 - page 15

    13 Configure the Access Point Configure the AP Client Router (CPEs) 1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Access Point and click Next . 3. LAN Settings: Set the IP Address to the same subnet with the root AP or router that you want to connect to, and click Next. 4 . Wireless AP Settings: a. Create a new SSID ...

  • TP-Link WBS510 - page 16

    14 Hotspot Configure the Access Point Smartphone Laptop Tablet Access Point Hotspot is used to provide Internet access to wireless devices such as smartphones, tablets and laptops. Typically, columnar antennas are used in this environment. 1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Access Point and click Next . 3. ...

  • TP-Link WBS510 - page 17

    Specification H ardware features Wireless features Interface Dimensions Models Maximum Transmit Power 2 Operating Frequency 2 802.11 Standards Power Supply ESD Protection 1 Lightning Protection 1 Operating Humidity Operating Temperature Certication LAN0 (POE IN) : 10/100/1000Mbps Ethernet port LAN1: 10/100Mbps Ethernet port GND: Grounding termin ...

  • TP-Link WBS510 - page 18

    FA Q How to restore the Base Station to its factory default settings? With the Base Station powered on, press and hold the RESET button on the Base Station or the Remote Reset button on the passive PoE adapter for about 8 seconds until the Wireless Signal Strength LEDs flash. What is Pharos MAXtream? Pharos MAXtream is a proprietary protocol develo ...

  • TP-Link WBS510 - page 19

    2. Click Start , the PharOS will begin to analyze the power of frequency . Observe the curves for a period of time, and then click stop. Note that the relatively low and continuous part of the average curve indicates less radio noise. Here, we use the figure below as an example. 3. When choosing channel/frequency, you should avoid the spectrum with ...

  • TP-Link WBS510 - page 20

    FC C ST A TEMENT CE M ark W arnin g IC ST A TEMENT Safety Information This equipment has been tested and found to comply with the limits f or a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide r easonable protection against harmful interference when the equipment is operated in a commercial environm ...

  • TP-Link WBS510 - page 21

    NC C Notice & BSMI Notic e 注意! 安全諮詢及注意事項 依據 低功率電波輻射性電機管理辦法 第十二 條 經型式認證合格之低功率射頻電 機 ,非經許 可 ,公 司 、商號或使用 者 均不得擅自變更頻率、加大功率或變更原設計之特性或功能。 第十四 條 低功率射頻電機? ...

Manufacturer TP-Link Category Access Point

Documents that we receive from a manufacturer of a TP-Link WBS510 can be divided into several groups. They are, among others:
- TP-Link technical drawings
- WBS510 manuals
- TP-Link product data sheets
- information booklets
- or energy labels TP-Link WBS510
All of them are important, but the most important information from the point of view of use of the device are in the user manual TP-Link WBS510.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals TP-Link WBS510, service manual, brief instructions and user manuals TP-Link WBS510. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product TP-Link WBS510.

Similar manuals

A complete manual for the device TP-Link WBS510, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use TP-Link WBS510 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of TP-Link WBS510.

A complete TP-Link manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual TP-Link WBS510 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the TP-Link WBS510, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the TP-Link WBS510, that we can find in the current document
3. Tips how to use the basic functions of the device TP-Link WBS510 - which should help us in our first steps of using TP-Link WBS510
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with TP-Link WBS510
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of TP-Link WBS510 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning TP-Link WBS510?

Use the form below

If you did not solve your problem by using a manual TP-Link WBS510, ask a question using the form below. If a user had a similar problem with TP-Link WBS510 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (1)

андрюха

где можна найти конкретную инструкцию по подключению? Как клиент.