Manual Grizzly 1008

17 pages 0.5 mb
Download

Go to site of 17

Summary
  • Grizzly 1008 - page 1

    VERTICAL MILLING MACHINE MODEL G1004/G1008 INSTRUCTION MANUAL COPYRIGHT © 1999 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED OCTOBER, 1999. PRINTED IN U.S.A. ...

  • Grizzly 1008 - page 2

    -2 - G1004/1008 Vertical Milling Machine Table Of Contents PAGE 1. SAFETY SAFETY RULES FOR POWER TOOLS ..................................................................................3-4 ADDITIONAL SAFETY FOR MILLING MACHINES ....................................................................5 2. CIRCUIT REQUIREMENTS 110 VOLT OPERATION ......... ...

  • Grizzly 1008 - page 3

    -3- Safety Instructions For Power Tools SECTION 1: SAFETY 5. KEEP CHILDREN AND VISITORS AWAY . All children and visitors should be kept a safe distance from work area. 6. MAKE WORK SHOP CHILD PROOF with padlocks, master switches, or by removing starter keys. 7. DON’T FORCE TOOL . It will do the job better and safer at the rate for which it was de ...

  • Grizzly 1008 - page 4

    -4 - G1004/1008 Vertical Milling Machine 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheat ...

  • Grizzly 1008 - page 5

    -5- G1004/1008 Vertical Milling Machine Additional Safety Instructions For The Vertical Milling Machine 9. ALWAYS use a brush to remove chips after the cutter has stopped. Never use a rag to remove chips. 10. NEVER operate mill if any part is damaged or broken until it is properly repaired or replaced. 11. BE SURE cutter, workpiece and machine part ...

  • Grizzly 1008 - page 6

    -6 - G1004/1008 Vertical Milling Machine 110V Operation The motor supplied with the G1004/G1008 is a dual-voltage 110/120V or 220/240V motor. (For information on operating at 220V, see the section following entitled 220V Operation.) Under normal use, the motor draws approximately 16 amps @ 110V, therefore it should be connected to a circuit that is ...

  • Grizzly 1008 - page 7

    -7- G1004/1008 Vertical Milling Machine We have covered some basic electrical requirements for the safe operation of your Milling Machine. These requirements are not necessarily comprehensive. You must be sure that your particular electrical con- figuration complies with local and state codes. Ensure compliance by checking with your local municipal ...

  • Grizzly 1008 - page 8

    -8 - G1004/1008 Vertical Milling Machine To operate this, or any power tool, safely and efficiently, it is essential to become as familiar with its characteristics as possible. The time you invest before you begin to use your Model G1004/G1008 will be time well spent. DO NOT operate this machine until you are completely familiar with the con- tents ...

  • Grizzly 1008 - page 9

    -9- G1004/1008 Vertical Milling Machine The G1004/G1008 is a heavy machine, 1,010 lbs. shipping weight. DO NOT over-exert yourself while unpacking or moving your machine – you will need assistance. Serious personal injury may occur if safe moving methods are not followed. When moving, always insure that you have enough clear- ance in the path way ...

  • Grizzly 1008 - page 10

    -10 - G1004/1008 Vertical Milling Machine Clean Up The unpainted surfaces are coated with a waxy oil to protect them from corrosion during ship- ment. Remove this protective coating with a sol- vent cleaner or citrus-based degreaser. Avoid chlorine-based solvents as they may damage painted surfaces should they come in contact. Always follow the usa ...

  • Grizzly 1008 - page 11

    -11- G1004/1008 Vertical Milling Machine Assembly of the G1004/G1008 is straightforward. We have organized the assembly process into steps. Please follow them in sequence. ORDER OF ASSEMBLY A. Leveling B. Mounting Handles C. Install Collet or Arbor D. Fly Cutter E. Knee Hand Crank Tools Required: A complete set of metric Allen ® wrenches will be n ...

  • Grizzly 1008 - page 12

    -12 - G1004/1008 Vertical Milling Machine 4. Turn the hex head at the top of the drawbar (located on the top, front of the head) clock- wise until the threads at the bottom of the drawbar mesh with the female threads in the top of the collet or arbor. 5. When using a collet: Insert the cutter in the hole at the bottom of the collet and contin- ue t ...

  • Grizzly 1008 - page 13

    -13- G1004/1008 Vertical Milling Machine This diagram shows belts positioned at A and II. As the chart shows, these positions will yield 1720 RPM. BELT POSITIONING CHART The motor is mounted on a plate hinged to the column. The motor assembly can be released by turning the handle at the side of the motor. Once the motor tension is released, the bel ...

  • Grizzly 1008 - page 14

    -14 - G1004/1008 Vertical Milling Machine Graduated Dials SECTION 6: ADJUSTMENTS The graduated dials on the handwheels for the table and fine feed can be indexed or “zeroed” to help make accurate and convenient movements. Each dial can be reset or locked with the setscrew or thumb screw provided. Example: Suppose you want to drill a series of h ...

  • Grizzly 1008 - page 15

    -15- Your Model G1004/G1008 milling machine requires very little maintenance. A thorough cleaning, now and again, will increase the machine’s durability and efficiency by removing chips and grime that can gum up moving parts. An occasional application of a protective spray coating will keep the table and other bare metal parts from rusting and pi ...

  • Grizzly 1008 - page 16

    -16 - G1004/1008 Vertical Milling Machine The following pages contain parts diagram, parts list and Warranty/Return information for your Model G1004/1008 mill. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department. Our trained service technicians will be glad to ...

  • Grizzly 1008 - page 17

    -17- G1004/1008 Vertical Milling Machine Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s s ...

Manufacturer Grizzly Category Drill

Documents that we receive from a manufacturer of a Grizzly 1008 can be divided into several groups. They are, among others:
- Grizzly technical drawings
- 1008 manuals
- Grizzly product data sheets
- information booklets
- or energy labels Grizzly 1008
All of them are important, but the most important information from the point of view of use of the device are in the user manual Grizzly 1008.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Grizzly 1008, service manual, brief instructions and user manuals Grizzly 1008. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Grizzly 1008.

Similar manuals

A complete manual for the device Grizzly 1008, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Grizzly 1008 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Grizzly 1008.

A complete Grizzly manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Grizzly 1008 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Grizzly 1008, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Grizzly 1008, that we can find in the current document
3. Tips how to use the basic functions of the device Grizzly 1008 - which should help us in our first steps of using Grizzly 1008
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Grizzly 1008
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Grizzly 1008 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Grizzly 1008?

Use the form below

If you did not solve your problem by using a manual Grizzly 1008, ask a question using the form below. If a user had a similar problem with Grizzly 1008 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)