Manual Q-Logic APS-610

10 pages 0.3 mb
Download

Go to site of 10

Summary
  • Q-Logic APS-610 - page 1

    Model APS-610 Installation Manual SELECT ABLE FEA TURES Note: The method of manual override can either be selected to operate from the valet switch or operate as custom code. Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual. Note: When both Passive Arming and V oltage Sensing ...

  • Q-Logic APS-610 - page 2

    Page 2 Fourth Press and release the valet switch 3 chirps = headlight output when arming and disarming Press transmitter Lock button to change 4 chirps = headlight output off Press transmitter Lock button to change 1 chirp = headlight output when arming Press transmitter Lock button to change 2 chirps = headlight output when disarming or Fifth Pres ...

  • Q-Logic APS-610 - page 3

    Page 3 If during the program sequence receiver channel 1 is programmed, and received channel 2 is skipped over , as indicated in the transmitted program guide, then the unit will operate as a single button lock/unlock unit from that transmitter . It is possible to have one transmitter programmed for single button lock/unlock, and one transmitter pr ...

  • Q-Logic APS-610 - page 4

    Page 4 Whichever mounting method is selected, make certain that the sensitivity adjustment is accessible for use later in the installation. WIRING THE SYSTEM Large 10 Pin Edge Connector: Red/White (5Amp) & Red (15Amp) Fused Wires: +12 VDC Constant Battery Source This wire controls the sensitivity of the voltage sensing circuit, which detects th ...

  • Q-Logic APS-610 - page 5

    Page 5 Orange Wire: 300 mA Ground Output When Armed - N. C. Starter Disable This wire is provided to control the starter cut relay . Connect the orange wire to terminal 86 of the relay . Connect relay terminal 85 to an ignition wire in the vehicle that is live when the key is in the on and crank positions, and off when the key is in the off positio ...

  • Q-Logic APS-610 - page 6

    Page 6 Note: This is a normally opened starter cut arrangement, and when power is removed from the security system, the starter disable feature will remain operational, and the vehicle will not start. Audiovox does not recommend using the Orange w/ White trace wire to interrupt anything but the starting circuit of the vehicle. Dark Green Wire: ( - ...

  • Q-Logic APS-610 - page 7

    Page 7 2 Pin White Connector: Dash Mounted L.E.D. Route the red and blue wires in the 2 pin white connector from the L.E.D. to the control module, and plug it into the mating white connector on the side of the module. 4 Pin White Connector: Shock Sensor Route the red, black, green and blue wires in the 4 pin white connector from the shock sensor to ...

  • Q-Logic APS-610 - page 8

    Page 8 Next, locate the drivers door unlock motor wire and cut it at a convenient location to allow wiring of the White and Dark Blue wires. Dark Blue will connect to the vehicle side of the cut wire and White will connect to the "Unlock Drivers Door Motor" side of the cut wire. Most vehicles door lock/unlock motor legs rest at ground, an ...

  • Q-Logic APS-610 - page 9

    Page 9 COMPLETING THE INST ALLA TION Antenna Wire: Be sure to extend the thin black antenna wire to it’s full length, and cable tie into place where it cannot be damaged. Avoid wrapping this wire around major , high current wire looms. Adjusting the Shock Sensor: If used, the sensitivity of the pre-detect circuit is automatically set 30% less sen ...

  • Q-Logic APS-610 - page 10

    © 2000 Audiovox Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-5758A ...

Manufacturer Q-Logic Category Automobile Accessories

Documents that we receive from a manufacturer of a Q-Logic APS-610 can be divided into several groups. They are, among others:
- Q-Logic technical drawings
- APS-610 manuals
- Q-Logic product data sheets
- information booklets
- or energy labels Q-Logic APS-610
All of them are important, but the most important information from the point of view of use of the device are in the user manual Q-Logic APS-610.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Q-Logic APS-610, service manual, brief instructions and user manuals Q-Logic APS-610. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Q-Logic APS-610.

Similar manuals

A complete manual for the device Q-Logic APS-610, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Q-Logic APS-610 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Q-Logic APS-610.

A complete Q-Logic manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Q-Logic APS-610 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Q-Logic APS-610, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Q-Logic APS-610, that we can find in the current document
3. Tips how to use the basic functions of the device Q-Logic APS-610 - which should help us in our first steps of using Q-Logic APS-610
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Q-Logic APS-610
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Q-Logic APS-610 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Q-Logic APS-610?

Use the form below

If you did not solve your problem by using a manual Q-Logic APS-610, ask a question using the form below. If a user had a similar problem with Q-Logic APS-610 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (1)

monluja

Ich suche eine Benutzeranleitung für Dymo 3500 in deutsch.