Manual Frigidaire 2020213A0362

10 pages 0.49 mb
Download

Go to site of 10

Summary
  • Frigidaire 2020213A0362 - page 1

    ...

  • Frigidaire 2020213A0362 - page 2

    Recommended grounding method: For your personal safety, this appliance must be grounded. This air conditioner includes a power supply cord with a 3-prong grounding plug. T o minimize possible electrical shock hazard: -cord must be plugged into a mating 3-prong grounding-type wall receptacle, -must be grounded in accordance with National Electrical Code (ANSI/NFPA 70- latest version) and -all local codes and ordinances. If a mating 3-prong grounding-type wall receptacle is not available, it is the responsibility of the consumer to have a properly grounded 3-prong wall receptacle installed by a qualified electrician. Electrical Connection Electrical ground is required on this appliance. Prepar ...

  • Frigidaire 2020213A0362 - page 3

    1. Make sure you have all the necessary parts. Installation kit contents: 1. Platform (1) 2. Support brace (1) 3. Adjustment bolt (1) 4. Hex flange nut - 1/4" (1) 5. Track seal (1) 6. Side channel seal (1) 7. Foam seal strip/Sash seal 8. Safety bracket (1) 9-11. Screw - #10 x 2-1/2" flat-head (2), OR Screw - #10 x 1-3/4" pan-head (2), OR Screw - #10 x 1" pan-head (2) 12. Screw - #8 x 3/4" pan head (6) 13. Screw - #8 x 3/4" self-threading (7) 14. Window locking bracket (1) 15. Plastic window panel (1) 16. Side channel (2) 17. Screw - #8 x 3/8" truss head (6) 18. Panel frame/seal assembly (1) NOTE: Use scale below to measure length of your screws. The scale w ...

  • Frigidaire 2020213A0362 - page 4

    Choose a window that allows the cooled air to flow freely and directly into room(s) you wish to cool. Remember, it is difficult to move air around corners. Also, choose a window that is within 6 feet of an electrical outlet. (See Meeting Electrical Requirements/Receptacle wiring needs.) Do not use an extension cord. 3. Choose the proper window location. Installing Unit in a Sliding Window 1. Attach support brace to platform as shown. Use adjustment bolt and hex flange nut to complete assembly. Choose slot and adjustment bolt hole locations that will create a 45 degree angle between platform and support brace. Try assembly in the window to determine if platform will rest properly, and allow p ...

  • Frigidaire 2020213A0362 - page 5

    4. Peel off protective backing from track seal. Apply seal to room side of window track. Center of seal strip should coincide with the line marked in Step 2. The two screw holes drilled in Step 3 should be directly above seal strip in the inner track. 5. Securely attach a siding-protection board to side of house. NOTE: Siding-protection board should be long enough to span 2 wall studs. 6. Place platform assembly, with platform tab against inside of window track, and attach it to window jamb. Use appropriate length screws (Items 9-11 in Preparing For Installation). 7. Adjust platform assembly so that outside edge is 3/16-inch lower than inside edge, as shown right. This ensures proper water d ...

  • Frigidaire 2020213A0362 - page 6

    Slide inner window sash firmly against Cabinet. 10. Clamp plastic window panel between a board and a work table, and cut along cutting line with a fine tooth saw. Remove any burrs with a file. 11. Fasten side channels to the sides of the AC using 3 screws (Item 17) per channel. Start with first screw at top of channel. Make sure hook ends of channels face toward back of unit. 12. Slide plastic window panel into panel frame, with the smooth side to the room. Slide panel frame assembly into side channels of the AC cabinet. Make sure plastic window panel is firmly enclosed on all sides by the retainer grooves. 13. Cut side channel seal into 2 equal lengths. Remove protective backing and apply i ...

  • Frigidaire 2020213A0362 - page 7

    16. Slide inner window sash firmly against side of the cabinet. Make sure not to peel the seal strips from the window track and cabinet side channels. If the panel frame does not fit snugly to the inner window sash, secure the panel frame to the sash with #8x3/4-inch screws, or #8-32x3/4-inch self- threading screws. Use the partially plugged holes in the panel frame. Drill 1/8-inch pilot holes for the screws. 17. Hook the safety bracket over the base of the unit and fasten it to the front of the platform assembly. Use a #8-32x3/4-inch self-threading screw. NOTE: The bracket prevents movement of the air conditioner (either in or out) after completing the installation. 18. Stuff the foam seal ...

  • Frigidaire 2020213A0362 - page 8

    Installing the Unit in a Casement Window NOTE: Open the window the maximum amount to allow for clearance of the cabinet. The crank handle should be removed to allow the platform to be fastened to the jamb. If the window cannot open far enough (more than 15-1/2 inches) for the cabinet to clear the window, remove the window entirely by drilling out the rivets. Bolts can serve as the pivots in the future. T o avoid crank handle and window clearance problems, the unit can be installed in a stationary sash section. However, the horizontal mullion and the 2 glass panels must be removed before installation. 1. Attach support brace to platform as shown. Use the adjustment bolt and hex flange nut to ...

  • Frigidaire 2020213A0362 - page 9

    5. Adjust the platform assembly so that the rear of the air conditioner will be 3/16-inch lower than the front. This ensures proper water drainage from the air conditioner. NOTE: A projection below the base of the air conditioner will require the rear of the platform to be 7/16-inch lower than the front to create the 3/16-inch slant from front to rear. 6. Securely attach a siding-protection board to the side of the house where the platform assembly hit the house. The siding-protection board should be long enough to span 2 wall studs. 7. Measure the height of the window opening from the top of the platform assembly. Subtract 20-5/8 inches. Mark this measurement on the plastic window panel, al ...

  • Frigidaire 2020213A0362 - page 10

    11. Cut side channel seal into 2 equal lengths. Remove the protective backing and apply it to the rear side of the cabinet side channels, starting just below the panel frame assembly. Pinch off excess length so the seal is even with the bottom of the cabinet side channel. 12. To remove front NOTE: DO NOT push or pull air direction louvers. 13. Place the air conditioner in the window opening as shown to the right. It should sit on the platform assembly so that the window panel frame, and the cabinet side channels are against the top and side window jambs. Side channels should overlap side window jambs equally. 14. Drill two 9/64-inch diameter pilot holes in the top window jamb in line with th ...

Manufacturer Frigidaire Category Air Conditioner

Documents that we receive from a manufacturer of a Frigidaire 2020213A0362 can be divided into several groups. They are, among others:
- Frigidaire technical drawings
- 2020213A0362 manuals
- Frigidaire product data sheets
- information booklets
- or energy labels Frigidaire 2020213A0362
All of them are important, but the most important information from the point of view of use of the device are in the user manual Frigidaire 2020213A0362.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Frigidaire 2020213A0362, service manual, brief instructions and user manuals Frigidaire 2020213A0362. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Frigidaire 2020213A0362.

A complete manual for the device Frigidaire 2020213A0362, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Frigidaire 2020213A0362 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Frigidaire 2020213A0362.

A complete Frigidaire manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Frigidaire 2020213A0362 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Frigidaire 2020213A0362, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Frigidaire 2020213A0362, that we can find in the current document
3. Tips how to use the basic functions of the device Frigidaire 2020213A0362 - which should help us in our first steps of using Frigidaire 2020213A0362
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Frigidaire 2020213A0362
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Frigidaire 2020213A0362 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Frigidaire 2020213A0362?

Use the form below

If you did not solve your problem by using a manual Frigidaire 2020213A0362, ask a question using the form below. If a user had a similar problem with Frigidaire 2020213A0362 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)