Manual Porter-Cable MS200

13 pages 4.93 mb
Download

Go to site of 13

Summary
  • Porter-Cable MS200 - page 1

    MEDIUM CROWN ST APLER Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT P ...

  • Porter-Cable MS200 - page 2

    2 Matthew G. Popik Vice President of Engineering PORTER ✦ ✦ CABLE Porter-Cable Corporation 4825 Highway 45 North Jackson, TN 38305 Date of Manufacture: ___________________________ Fecha de fabricación:, Date de fabrication: Serial No: ______________________________________ Número de serie:, Nombre d'ordre GB ENGLISH EC-DECLARA TION OF CO ...

  • Porter-Cable MS200 - page 3

    3 indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. used without the safety al ...

  • Porter-Cable MS200 - page 4

    4 Fig. 6 Fig. 5 Fig. 2 Fig. 3 Fig. 4 1. Read and understand tool labels and manual. Failure to follow warnings could result in DEATH or SERIOUS INJURY . Fig. 1. 2 . Operator and others in work area MUST wear safety glasses with side shields. These safety glasses must conform to ANSI Z87.1 requirements (approved glasses have “Z87” printed or sta ...

  • Porter-Cable MS200 - page 5

    5 9. Do not connect tool to pressure which potentially exceeds 200 PSI (13.7 BAR). 10. Only use air hose that is rated for a maximum working pressure of at least 150 PSI (10.3 BAR) or 150% of the maximum system pressure, which ever is greater. 11. Connect tool to air supply hose with a coupling that automatically removes all pressure from the tool ...

  • Porter-Cable MS200 - page 6

    6 21. Remove finger from trigger when not driving fasteners. Never carry tool with finger on trigger. In “Contact Actuation Mode” tool will fire a fastener if safety is bumped while trigger is depressed. Fig. 14. 22. Do not overreach. Keep proper footing and balance at all times when using or handling the tool. 23. Fire fasteners into work surf ...

  • Porter-Cable MS200 - page 7

    7 Employer must enforce compliance with the safety warnings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and understand tool labels and manual. Failure to follow warnings could result in DEATH or SERIOUS IN ...

  • Porter-Cable MS200 - page 8

    8 Only use approved Porter-Cable fasteners. Operator and others in work area MUST wear safety glasses with side shields. Always wear ANSI Z87.1 approved safety glasses, and ANSI S3.19 approved hearing protection when preparing or operating the tool. Never use a tool that is leaking air, has missing or damaged parts, or requires repair. 2. Pull stap ...

  • Porter-Cable MS200 - page 9

    9 USING THE TOOL WITH SELECT ABLE TRIGGERING OPTIONS Complete all steps of PREPARING THE TOOL before using the tool. This tool is shipped from the factory with a selectable trigger set in the “SINGLE SEQUENTIAL ACTUATION” firing mode as described in number 1 below. The selectable trigger can be set for the “CONTACT ACTUATION” firing mode as ...

  • Porter-Cable MS200 - page 10

    10 Keep fingers AWAY from trigger when not driving fasteners to avoid accidental firing. Never carry tool with finger on trigger. In “Contact Actuation Mode” t ool will fire a fastener if safety is bumped while trigger is depressed. Never point tool at yourself or others. Never attempt to drive a fastener into material that is too hard, or at t ...

  • Porter-Cable MS200 - page 11

    11 CLEAN AND INSPECT DAIL Y Disconnect tool from air supply before cleaning and inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammable cleaning solutions to wipe exterior of tool only if necessary. DO NOT SOAK tool with cleaning solutions. Such solutions can damage int ...

  • Porter-Cable MS200 - page 12

    12 2. Tool does nothing or Inadequate air supply. Verify adequate air supply. operates sluggishly. Inadequate lubrication. Put 5 or 6 drops of oil into air inlet. Worn or damaged Install Overhaul Kit. o-rings or seals. 3. Air leak near bottom Loose screws. Tighten screws. of tool. Worn or damaged Install Overhaul Kit. o-rings or bumper. 4. Tool jam ...

  • Porter-Cable MS200 - page 13

    The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...

Manufacturer Porter-Cable Category Staple Gun

Documents that we receive from a manufacturer of a Porter-Cable MS200 can be divided into several groups. They are, among others:
- Porter-Cable technical drawings
- MS200 manuals
- Porter-Cable product data sheets
- information booklets
- or energy labels Porter-Cable MS200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Porter-Cable MS200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Porter-Cable MS200, service manual, brief instructions and user manuals Porter-Cable MS200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Porter-Cable MS200.

A complete manual for the device Porter-Cable MS200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Porter-Cable MS200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Porter-Cable MS200.

A complete Porter-Cable manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Porter-Cable MS200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Porter-Cable MS200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Porter-Cable MS200, that we can find in the current document
3. Tips how to use the basic functions of the device Porter-Cable MS200 - which should help us in our first steps of using Porter-Cable MS200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Porter-Cable MS200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Porter-Cable MS200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Porter-Cable MS200?

Use the form below

If you did not solve your problem by using a manual Porter-Cable MS200, ask a question using the form below. If a user had a similar problem with Porter-Cable MS200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)