English dropdown-ico

Manual Fujitsu 5000

72 pages 1.04 mb
Download

Go to site of 72

Summary
  • Fujitsu 5000 - page 1

    i DESKPOWER 5000 Series User’s Manual Fujitsu endeavours to ensure that the information in this document is correct, but accepts no liability for any error or omission in the same. Any procedures described in this document for operating Fujitsu products should be read and understood by the operator before such products are used. To ensure that Fu ...

  • Fujitsu 5000 - page 2

    ii IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions carefully. Save these instructions for future reference. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this product nea ...

  • Fujitsu 5000 - page 3

    iii 13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally when the operating i ...

  • Fujitsu 5000 - page 4

    iv Before reading this manual This section describes safety precautions and convention used in this manual. Be sure to read this. For Safe Operation This manual contains important information for using the DESKPOWER personal computer. Read this manual thoroughly before using your PC. In particular, “Safety Precautions” in this manual must be re ...

  • Fujitsu 5000 - page 5

    v Using this Product for High-Safety Applications This product is for office, personal, home, ordinary industry and other general use. It is not designed and manufactured for use in high-safety applications. Do not use this product for such applications without taking measures to satisfy the high-safety requirements. High-safety applications requir ...

  • Fujitsu 5000 - page 6

    vi Microsoft Service Pack Microsoft Corp. offers Service Pack to provide the users of Microsoft ® Windows ® with more stable system operation (http://www.microsoft.com/). The latest version of the Service Pack helps you configure the most stable system using Microsoft ® Windows ® provided at that time by Microsoft Corp. We recommend you to use ...

  • Fujitsu 5000 - page 7

    vii Conventions Used in This Manual Warning messages This manual uses various signs. These signs urge the user to use the equipment safely so as to prevent personal injury and/or property damage. The following are alert signals and explanations. The signs should be understood before proceeding to subsequent portions of this manual. This indicates a ...

  • Fujitsu 5000 - page 8

    viii Command entry (keying in) In this manual, a command entry is represented as follows: diskcopy a: a: ↑↑ • Where character spacing is provided as shown by [ ↑ ], press the [Space] key once. Commands, an example of which is given above in lowercase, can also be entered in uppercase. • [CD-ROM drive] indicates the name of the CD-ROM driv ...

  • Fujitsu 5000 - page 9

    ix Reference to products In this manual, the product names are referred to as follows: This manual includes information on other operating systems. Product name Description used in the manual Microsoft ® Windows ® XP Professional Microsoft ® Windows ® XP Home Edition Microsoft ® Windows ® 2000 Professional Microsoft ® Windows NT ® Workstati ...

  • Fujitsu 5000 - page 10

    x Recycling Disposal of the PC unit Disposal of the PC unit (including accessories except the LCD unit) is controlled by the Waste Disposal and Public Cleaning Law. ● To institutional and corporate customers Personal computers must be disposed of as industrial waste. Institutional and corporate customers are obliged to entrust an authorized indus ...

  • Fujitsu 5000 - page 11

    xi Warning and caution labels Your PC bears the warning and caution labels as shown below. The warning and caution labels must not be removed or damaged. Rear of the PC main unit ATTENTION 115V of voltage switch in the power supply corresponds to 100-120V 230V of voltage switch in the power supply corresponds to 200-240V WARNING • Before mounting ...

  • Fujitsu 5000 - page 12

    xii Before Reading This Manual This section contains cautions for safe operation, representations and symbols used in this manual. Be sure to read this first! Chapter 1 Part Names This chapter provides the names and functions of individual parts. Chapter 2 Installation and Connection This section describes the location of installation and installat ...

  • Fujitsu 5000 - page 13

    xiii Contents CHAPTER 1 P ar t Names 1 P art Names and Functions .............................................................. 2 F ront of the PC Unit .......................................................................................... 2 Rear of the PC Unit ..................................................................................... ...

  • Fujitsu 5000 - page 14

    xiv CHAPTER 4 System Expansion 1 Before Installing a P eripheral De vice ............................................ 42 2 Remo ving the Cover ....................................................................... 44 Removing the Cov er ....................................................................................... 44 3 Installing Memory M ...

  • Fujitsu 5000 - page 15

    CHAPTER 1 Part Names CHAPTER 1 Bennett (01-08) 6/7/02, 3:50 PM 1 ...

  • Fujitsu 5000 - page 16

    2 1 Part Names and Functions This section explains the names and functions of the parts of the PC unit and the motherboard.      Point The remaining part of this manual assumes vertical placement.When you place the PC unit horizontally, be careful about geometrical difference. ■ Front of the PC Unit 1 Power button Press this button ...

  • Fujitsu 5000 - page 17

    3 3 Disk access lamp This lamp lights up while the hard disk is accessed. 4 USB connector Slide the cover down and connect USB peripherals. 5 Foot Used for placing the PC. This also prevents the PC in a vertical placement from tipping over. 6 CD eject button Press this button to load or eject a CD-ROM disk or a music CD.This button can be used when ...

  • Fujitsu 5000 - page 18

    4 ■ Rear of the PC Unit 1 Burglarproof lock Install a key to prevent burglary of the components in the PC. 2 Expansion card slots Insert an optional expansion card to this slot. This slot accommodates a half-size PCI card. Put the supplied nylon band through the USB fixture slit to tie up the cable. 3 Inlet Connect the power code of the PC unit t ...

  • Fujitsu 5000 - page 19

    5 6 Serial connector Connect an RS-232C device connector. 7 Parallel connector Connect a printer or scanner cable. 8 CRT connector Connect the cable of an analog RGB display. 9 LAN connector Connect a LAN cable. 10 USB connector Connect a USB device. 11 Line OUT terminal A terminal for sound output.Connect the input terminal of audio equipment to t ...

  • Fujitsu 5000 - page 20

    6 ■ Inside the PC Unit 1 Internal hard disk drive An IDE-compliant hard disk drive. 2 Expansion card slots Insert an optional expansion card to this slot. This slot accommodates a half-size PCI card. A SCSI card allows you to use an external hard disk drive or a magneto-optical disk drive. 3 Power supply unit CHAPTER 1 Bennett (01-08) 12/6/02, 10 ...

  • Fujitsu 5000 - page 21

    7 ■ Motherboard 1 CPU 2 DIMM slots Memory modules are inserted into these slots. Increasing the memory capacity increases the amount of data that the system can read at one access, thereby improving the processing capability of the PC. When viewed from the front of the PC unit, the front slot is DIMM1 and the behind is DIMM2. The standard memory ...

  • Fujitsu 5000 - page 22

    CHAPTER 2 Installation and Connection CHAPTER 2 Bennett (09-18) 6/8/02, 10:11 AM 9 ...

  • Fujitsu 5000 - page 23

    10 1 Installation This section describes the location and installation of the PC. ■ Location of Installation Avoid the following conditions when installing your PC. ● Location with a large amount of humidity, dusts and oily smoke. ● Location with poor ventilation. ● Location with a fire source. ● Bathroom, shower room, and other location ...

  • Fujitsu 5000 - page 24

    11 ● When using a single foot When installing your PC in the vertical layout and in contact withthe wall, use the following installation procedure. 1 Disassemble the foot. 2 Mount the disassembled foot on the PC unit. Fix the foot by tightening the setscrew. ❒ Horizontal Placement 1 Disassemble the foot. 2 Place the PC on the disassembled foot. ...

  • Fujitsu 5000 - page 25

    12      Point You can also mount five rubber feet at the center and four corners of the PC bottom plate during horizontal placement. Take care not to contact the rubber feet with the foot of PC during vertical placement. Wipe and clean the mounting surface of the PC when you fix the rubber feed to the PC housing. Also, do not slide t ...

  • Fujitsu 5000 - page 26

    13 ❒ Horizontal Placement 17-inch or less CRT display unit (below 19kg) can be placed on the PC housing in horizontal layout. Display Keyboard Foot PC unit Mouse      Point The remaining part of this manual assumes vertical PC placement. When you place the PC unit horizontally, be careful about geometrical difference. CHAPTER 2 Ben ...

  • Fujitsu 5000 - page 27

    14 Connect the display, keyboard, and power cord to the PC. WARNING ● Connect the grounding leads to the device that needs to be grounded before turning it on. You may get electrical shock if you do not provide grounding. Do not connect the grounding wire to the gas pipe. Otherwise it may cause a fire. ● Turn the PC and attached devices off and ...

  • Fujitsu 5000 - page 28

    15 ■ Connecting the Display/Keyboard/Mouse 1 Plugging the power cord into power receptacle. Plug the power cord of the display unit into the power outlet of the PC. 2 Plugging the power cord into inlet of display unit. Plug the other end of power cord into the power inlet at the rear of the display unit. 3 Connecting the mouse. Plug the mouse cab ...

  • Fujitsu 5000 - page 29

    16 4 Connecting the keyboard. Plug the keyboard cable into the socket at the rear of the PC, by facing the connector mark to the right and matching the connector color to the keyboard label at the rear of the PC. 5 Connecting the display cable to the PC unit. Securely plug the signal cable of the display unit into the display socket at the rear of ...

  • Fujitsu 5000 - page 30

    17 ■ Connect the Power Cord When you attach a peripheral device such as the display to your PC, plug its power cord into socket by following the instructions given. ● Do not plug or unplug the power cord with wet hands. ● Do not damage or modify the power cord. ● Do not compress, pull, twist, or heat the power cord. ● Do not use the power ...

  • Fujitsu 5000 - page 31

    18 1 Plug the power cord into the power inlet at the rear of the PC. 2 Connect the power cord to the 230 VAC power source. Plug the other end of power cord into the 230 VAC power receptacle. CHAPTER 2 Bennett (09-18) 6/11/02, 11:18 AM 18 ...

  • Fujitsu 5000 - page 32

    19  Cautions ● When turning on the PC for the first time after purchase, do not connect any peripheral equipment. ● The power lamp shines orange when the PC is in the standby mode. ● Before turning the PC power switch ON, make sure that the display unit has been connected to the PC. If the display unit is not connected, it is not recognize ...

  • Fujitsu 5000 - page 33

    20 ■ How to Power On CAUTION ● Do not carry or give impact/vibrations to the PC when it is on. Or, it may cause a failure. 1 Press the display power button. Nothing appears on the screen at this time. 2 Press the PC power button. The green power lamp will light on both the PC and display unit. When you turn on the PC, it displays a FUJITSU logo ...

  • Fujitsu 5000 - page 34

    21 4 Setting Up This section describes how to set up the Windows when you turn on the PC for the first time. Make sure that you follow the procedure described in this manual. Read the following Considerations before turning on the PC for setting up the Windows.  Considerations ● Do not perform the following before setting up Windows. If you do ...

  • Fujitsu 5000 - page 35

    22 ■ Setting Up Windows XP 1 Turn on the PC. After a few seconds, [Welcome to Microsoft Windows] appears. 2 Click [Next]. [License Agreement] is displayed. This License Agreement describes the agreement for using preinstalled Windows on the computer. 3 Read the [License Agreement] carefully, and click [I agree], and then [Next].     ? ...

  • Fujitsu 5000 - page 36

    23      Important You need to perform [Run this] to finalize the setup. Be sure to perform the procedure as it is described here. 12 Click [Perform]. Final setup is performed, and the restart message is displayed. 13 Click [OK]. The PC restarts. You have completed the Windows setup. ■ Setting Up Windows 2000      Poi ...

  • Fujitsu 5000 - page 37

    24 5 Fill out [Computer name], [Administrator password], and [Reenter password], and click [Next]. [Setting up network] appears. To set up the network, ask your network administrator to check the setup after completing the setup, and set it up for your operating environment. 6 Click [Standard setting] and [Next].      Point With [Sta ...

  • Fujitsu 5000 - page 38

    25      Point Make sure you select [User for this computer ...]. If you select items other than [User for this computer ...], the setup may not be carried out correctly. [Finishing the Network Identification Wizard] appears. 11 Click [Finish]. The [Windows logon] dialog box appears. 12 Enter the password you entered in the step 5, an ...

  • Fujitsu 5000 - page 39

    26 ■ Problem During Setup? If the computer freezes during setup, or if you have any other problem, see the following items. ❒ The screen does not show anything when the computer is turned on. ● Turn of the computer, and check the connection of display. ❒ I cannot go on with the Windows setup. ● See “Turn off the computer”, turn off th ...

  • Fujitsu 5000 - page 40

    27  Cautions ● Before turning off the computer, finish the work and save your data. ● Before turning of the computer, make sure that the disk access lamp or floppy disk access lamp are all off. If you turn off the computer while these lamps are on, your data may not be saved, or the data stored in the floppy disk or hard disk may be damaged. ...

  • Fujitsu 5000 - page 41

    28  For Windows 2000: Click [Start] and [Shutdown], select [Shutdown] and click [OK].  For Windows Me: Click [Start] and [Exit Windows], select [Place into mode of readiness for turning off], and click [OK].      Point • If the power is not turned off by the above operation, cut the power by following steps below: 1. Press [C ...

  • Fujitsu 5000 - page 42

    CHAPTER 3 Hardware CHAPTER 3 Bennett (29-40) 12/6/02, 10:17 AM 29 ...

  • Fujitsu 5000 - page 43

    30 1 Keyboard This section explains the functions of the keys on the keyboard.      Point Key functions may vary depending on the operating system and applications used. See manuals attached to the operating system and applications. 1 Esc key Pressing this key cancels the operation the application program is executing. 2 F keys These ...

  • Fujitsu 5000 - page 44

    31 8 Caps Lock key Use the Caps Lock key to type alphabetical characters. Press [Shift] + [Caps Lock] to switch between uppercase and lowercase. 9 Ctrl key Use the Ctrl key in combination with another key. Its function varies with each application. 10 Windows key Press the Windows key to display the Start menu. 11 Alt key Use the Ctrl key in combin ...

  • Fujitsu 5000 - page 45

    32 2 CDs This section describes how to handle, insert, and remove a CD.  Notes on Handling Follow the following guidelines to prevent faults when handling a CD. Guidelines for CD Media ● Apply no label to any side of the disk. Do not use a ballpoint pen or pencil. ● Do not touch or damage the data side. ● Do not bend the disk or put a heav ...

  • Fujitsu 5000 - page 46

    33 ■ Inserting or Removing a CD ● Inserting a CD 1 Press the CD eject button. Press the middle of the CD eject button, and the CD tray pops out. 2 Pull the tray out with a hand. As shown in the figure, hold the center of the tray. 3 Mount the CD by facing its label to the left, and push the CD until it snaps onto the hub at the center of the tr ...

  • Fujitsu 5000 - page 47

    34 4 Manually push the tray until it clicks. The tray goes into the computer, and sets the CD.      Point • The CD access lamp lights when the CD is set. Wait until the CD access lamp turns off, and then do the following. • The tray is not set correctly, if you press the CD eject button while pushing in the tray. ● Removing the ...

  • Fujitsu 5000 - page 48

    35 3 Floppy Disks This section explains how to handle, insert, and remove a floppy disk.  Notes on Disk Handling To prevent faults, note the following when handling floppy disks. ● Keep the disks dry. ● Do not touch the disk inside. ● Do not bend the disk or put a heavy object on it. ● Keep the disks away from magnetism. ● Do not drop ...

  • Fujitsu 5000 - page 49

    36 ● Removing a Floppy Disk 1 Make sure that the floppy disk access lamp is off.      Point Do not press the floppy disk eject button while the floppy disk access lamp is on. Data stored on the disk may be damaged. 2 Press the Floppy disk eject button. The floppy disk comes out. Floppy disk access lamp CHAPTER 3 Bennett (29-40) 12/ ...

  • Fujitsu 5000 - page 50

    37 This section provides cautions on handling the hard disk drive.  Cautions To prevent faults, note the following. ● Data is read from the hard disk drive or written to it while the internal disk that stores data is rotating at high speeds. Since it is a very delicate device, do not carry the PC with the power on or do not apply shock or vibr ...

  • Fujitsu 5000 - page 51

    38 ■ Maintenance of the PC Unit CAUTION ● Before starting maintenance work, turn off the PC and all devices connected to it, and unplug them. Otherwise, electric shock may occur. ● Clean the PC using a soft dry cloth. Wipe remaining dirt off using a damp cloth, moistened with neutral detergent and wrung well. Once the dirt is wiped off, remov ...

  • Fujitsu 5000 - page 52

    39 3 Clean the inside of the mouse. Wipe the inside of the mouse, roller, and the bottom cover with a damp cloth. 4 Reassemble the ball and bottom cover. When the ball and the inside of the mouse are dry, reassemble the ball and cover. ■ Maintenance of the Keyboard Clean the PC using a soft dry cloth. ■ Cleaning CDs ● If the disk has dirt or ...

  • Fujitsu 5000 - page 53

    CHAPTER 4 System Expansion CHAPTER 4 Bennett (41-52) 12/6/02, 10:18 AM 41 ...

  • Fujitsu 5000 - page 54

    42 1 Before Installing a Peripheral Device This PC can accommodate various peripheral devices to expand its functions. CAUTION ● Use only peripheral devices recommended by Fujitsu. Otherwise, electric shock, fire or a fault may occur. CAUTION ● When installing or removing a peripheral device, do not remove screws other than those specified in t ...

  • Fujitsu 5000 - page 55

    43 ● After removing the feet, place the PC unit on a soft cloth. Placing the PC directly on a hard surface may cause scratches on the PC. ● Be careful with the cables and components inside. Do not damage or modify them. ● Be careful of static electricity. PC boards and electronic parts of internal peripheral devices are exposed. They may be d ...

  • Fujitsu 5000 - page 56

    44 2 Removing the Cover When mounting a peripheral device, remove the upper cover so that the inside can be seen. ■ Removing the Cover Remove the feet, if any, from the PC unit. Place the PC unit in a horizontal position and remove the upper cover. 1 Remove the two screws on the PC unit. 2 Remove the upper cover. Slide the upper cover to the fron ...

  • Fujitsu 5000 - page 57

    45 3 Installing Memory Modules Increasing the memory capacity increases the amount of data that the system can read at one access, thereby improving the processing capability of the PC.      Point If you want to install a memory module to the PC you have just purchased, set up Windows, turn off the PC, and then install the memory mod ...

  • Fujitsu 5000 - page 58

    46 ■ Location of Memory Modules ■ Applicable Memory Modules Use Fujitsu 1 84-pin DDR SDRAM DIMM memory (PC 2100 ECC-incompatible) memory modules. The maximum memory capacity is 1 GB (512 MB x 2). For the standard configuration, memory is installed in DIMM1.To add memory, install it in DIMM2. The memory module in slot DIMM1 must be changed depen ...

  • Fujitsu 5000 - page 59

    47 ■ Installing Memory Modules 1 Unplug the PC. 2 Remove the upper cover. 3 Remove the expansion card mounting bracket and reinforcing fitting. Remove the two screws and pull straight up the expansion card mounting bracket. (The reinforcing fitting is removed together with the expansion card mounting bracket.) When an expansion card has been inst ...

  • Fujitsu 5000 - page 60

    48 6 Install the expansion card mounting bracket and reinforcing fitting. Secure it with the two screws you have removed in Procedure3. 7 Installing Memory Modules Reinstall the upper cover.      Point To remove a memory module, open module hooks at both sides of the slot. Do not pull the hooks too violently. Otherwise, the memory mo ...

  • Fujitsu 5000 - page 61

    49 4 Installing an Expansion Card Expansion cards are used to enhance the PC functions.      Point If you want to install an expansion card to the PC you have just purchased, set up Windows, turn off the PC, and then install the card. CAUTION ● Before installing or removing an expansion card, turn off the PC and all devices connect ...

  • Fujitsu 5000 - page 62

    50 ■ Location of expansion Cards ■ Applicable Expansion Cards This PC accommodates a PCI expansion card. The PCI1 slot holds an expansion card with a maximum length of 176 mm (half size) and the PC2 slot holds an expansion card with a maximum length of 120 mm (half size). To run the expansion card, the generally called resource necessary for op ...

  • Fujitsu 5000 - page 63

    51 3 Remove the expansion card mounting bracket. Remove the two screws and pull straight up the expansion card mounting bracket When an expansion card has been installed, remove the cable from the card and remove the bracket. 4 Remove the slot cover. Remove one screw from the position where the expansion card is installed, and remove the slot cover ...

  • Fujitsu 5000 - page 64

    52 5 Insert the expansion card into the slot. Insert the expansion card into the slot, and secure it with the screw removed in Procedure 4. 6 Install the expansion card mounting bracket. Secure it with the four screws you have removed in Procedure 3. 7 Reinstall the upper cover.      Point To remove the expansion card, use the instal ...

  • Fujitsu 5000 - page 65

    CHAPTER 5 Technical Information CHAPTER 5 Bennett (53-60) 12/6/02, 10:31 AM 53 ...

  • Fujitsu 5000 - page 66

    54 1 List of Specifications ■ PC Specifications Display function Interface Product Name CPU Cache memory System bus BIOS ROM Main memory Memory slot Graphic accelerator Video RAM Video output signals Resolution/number of colors Floppy drive Harddisk drive (EIDE) Optical drive Auto Function Sound Controller PCM recording/playback functions MIDI pl ...

  • Fujitsu 5000 - page 67

    55 Product Name Power/Frequency Outer dimensions Weight Burglarproof lock *1: The capacity is automatically changed by Intel Dynamic Video Memory Technology according to system conditions. *2: Disk capacities are based on a conversion of 1 MB = 1000 2 bytes and 1 GB = 1000 3 bytes.Actual disk capacities based on conversion of 1 MB = 1024 2 bytes an ...

  • Fujitsu 5000 - page 68

    56 ■ LAN function LAN Controller Intel 82801DB(ICH4)integrated + 82562EM Transmission buffer RAM 3K bytes for transmission (send/receive) External Interface ISO8802-3 100BASE-TX/10BASE-T Transmission media Twisted pair cable *1 (100Mbps: Category 5, 10Mbps: Category 3 - 5) Transmission system Baseband Access method CSMA/CD Data transfer rate 100 ...

  • Fujitsu 5000 - page 69

    57 2 Connector Specifications The following table provides the pin assignment and signal names. ● CRT connector Pin number Signal name Direction Description 1 RED Output Red (R) signal output 2 GREEN Output Green (G) signal output 3 BLUE Output Blue (B) signal output 4 NC – Not connected 5 - 8 GND – Ground 9 +5V – +5V 10 GND – Ground 11 N ...

  • Fujitsu 5000 - page 70

    58 ● LAN connector (100BASE-TX/10BASE-T) Pin number Signal name Direction Description 1 TD+ Output Send data + 2 TD– Output Send data – 3 RD+ Input Receive data + 4 NC – Not connected 5 NC – Not connected 6 RD– Input Receive data – 7 NC – Not connected 8 NC – Not connected ● Parallel connector Pin number Signal name Direction De ...

  • Fujitsu 5000 - page 71

    59 ● Serial connector Pin number Signal name Direction Description 1 CD Input Carrier detect 2 RD Input Receive data 3 TD Output Transmission data 4 DTR Output Data terminal ready 5 GND – Ground 6 DSR Input Data set ready 7 RTS Output Request to send 8 CTS Input Clear to send 9 RI Input Ring indicate ● Mouse connector Pin number Signal name D ...

  • Fujitsu 5000 - page 72

    60 Glossary Symbol 100BASE-TX/10BASE-T ............................ 58 C CD - inser ting ............................................. 33 - removing ............................................ 33 - maintenance ...................................... 39 Connector specifications ............................ 57 CR T connector ......................... ...

Manufacturer Fujitsu Category Personal Computer

Documents that we receive from a manufacturer of a Fujitsu 5000 can be divided into several groups. They are, among others:
- Fujitsu technical drawings
- 5000 manuals
- Fujitsu product data sheets
- information booklets
- or energy labels Fujitsu 5000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Fujitsu 5000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Fujitsu 5000, service manual, brief instructions and user manuals Fujitsu 5000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Fujitsu 5000.

Similar manuals

A complete manual for the device Fujitsu 5000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Fujitsu 5000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Fujitsu 5000.

A complete Fujitsu manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Fujitsu 5000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Fujitsu 5000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Fujitsu 5000, that we can find in the current document
3. Tips how to use the basic functions of the device Fujitsu 5000 - which should help us in our first steps of using Fujitsu 5000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Fujitsu 5000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Fujitsu 5000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Fujitsu 5000?

Use the form below

If you did not solve your problem by using a manual Fujitsu 5000, ask a question using the form below. If a user had a similar problem with Fujitsu 5000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)