English dropdown-ico

Manual Texas Instruments APA100

42 pages 0.77 mb
Download

Go to site of 42

Summary
  • Texas Instruments APA100 - page 1

    AP A100 100−W Analog Input Class-D Amplifier TP A2001D1/T AS5111 August 2004 Audio Power Amplifiers User ’ s G uide SLOU170 ...

  • Texas Instruments APA100 - page 2

    IMPORT ANT NOTICE T exas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orde ...

  • Texas Instruments APA100 - page 3

    Information About Cautions and Warnings iii Preface Read This First About This Manual This user ’s guide describes the characteristics, operation, and the use of the AP A100 reference design board. It covers all pertinent areas involved to properly use this reference design board along with the devices that it supports. The physical PCB layout, s ...

  • Texas Instruments APA100 - page 4

    Related Documentation From T exas Instruments iv This is an example of a warning statement. A warning statement describes a situation that could potentially cause harm to you . Th e information in a caution or a warning is provided for your protection. Read each caution and warning carefully . Related Documentation From T exas Instruments T o obtai ...

  • Texas Instruments APA100 - page 5

    Contents v Contents 1 EVM Overview 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Features 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Power Requirements 1-2 . ...

  • Texas Instruments APA100 - page 6

    Contents vi Figures 1−1 THD+N vs Output Power (a), THD+N vs Frequency (b) 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−2 AP A100 EVM Block Diagram 1-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−1 AP A100 Split Plane T op Layout 2-2 . . . . . . . . . . . . . . . . . ...

  • Texas Instruments APA100 - page 7

    1-1 EVM Overview EVM Overview This reference design demonstrates how to make the TP A2001D1 and the T AS51 1 1 into a 100-W class-D amplifier . The user’s guide discusses how the TP A2001D1 is used as an analog input class-D modulator . The analog modulator i s input to the T AS51 1 1, which is an H-bridge that ef fectively extends the supply ran ...

  • Texas Instruments APA100 - page 8

    Features 1-2 1.1 Features This reference design or evaluation module (EVM) features the TP A2001D1, T AS51 1 1, and TL V2464A. For simplicity , this EVM is referred to as the AP A100 EVM to cover all parts that are supported in this user ’ s guide. The AP A100 EVM is an evaluation module designed for a quick and easy way to evaluate the functiona ...

  • Texas Instruments APA100 - page 9

    EVM Basic Function/Block Diagram 1-3 EVM Overview an d NPN transistor circuit is used to create the 3-V supply for the TP A2001D1 and TL V2464A; therefore, the user only needs to apply the single-supply voltage. A+ supply is used for powering the T AS51 1 1 and is input for the zener diode/NPN transistor circuit used to generate the 3-V supply for ...

  • Texas Instruments APA100 - page 10

    EVM Basic Function/Block Diagram 1-4 Figure 1−2. AP A100 EVM Block Diagram Audio Input Gain (TL V2464) Feedback and Integrator (TL V2464) Audio Output Analog Input Class-D Modulator TP A2001D1 H-Bridge (T AS51 1 1) ...

  • Texas Instruments APA100 - page 11

    2-1 PCB Design PCB Design This chapter gives layout guidelines for the AP A100 reference design. T opic Page 2.1 PCB Layout 2-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 Bill of Materials 2-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. ...

  • Texas Instruments APA100 - page 12

    PCB Layout 2-2 2.1 PCB Layout The critical part of the design lies particularly in the layout process. The EVM layout should be followed exactly for optimal performance. The main concern is the placement of components and the proper routing of signals. Place the bypass/decoupling capacitors as close as possible to the pins; properly separate the li ...

  • Texas Instruments APA100 - page 13

    PCB Layout 2-3 PCB Design Figure 2−2. AP A100 Split Plane Bottom Layout 2.1.2 H-Bridge Layout The H-bridge is laid out based on recommendations from the T AS51 1 1 data sheet and follows the same pattern as the DA VREF100 EVM board. 1) Keep local decoupling and bootstrap capacitors and resistors close to pins. J Minimize trace length to C29, and ...

  • Texas Instruments APA100 - page 14

    PCB Layout 2-4 3) Us e a split ground plane to keep high switching ground currents from the operational amplifier circuitry . 4) Place decoupling capacitors close to the TL V2464A and TP A2001D1 5) Place RC filter capacitors (C20, C23, and C24) close to the operational amplifier , with capacitor grounds connecting with a low−impedance path to the ...

  • Texas Instruments APA100 - page 15

    PCB Layout 2-5 PCB Design Figure 2−4. Bottom Copper and Silkscreen Figure 2−5. Drill Drawing SIZE QTY STM PL TD 18 4 PL TD 28 40 PL TD 42 21 PL TD 89 3 PL TD 1 16 6 PL TD 140 4 PL TD 3.4 INCH 2.5 INCH ...

  • Texas Instruments APA100 - page 16

    Bill of Materials 2-6 2.2 Bill of Materials T able 2−1. Parts List Reference Qty V alue Manufacturer Part Number Description C23,24 2 22 pF TDK C1608C0G1H220J 50 V , size 603, COG, 5% C13,19,20,R25 4 56 pF TDK C1608C0G1H560J 50 V , size 603, COG, 5% C6,9,1 1,12,14,17,18, 21,49,50 10 220 pF TDK C1608X7R1H221K 50 V , size 603, X7R, 10% C4,25 2 3300 ...

  • Texas Instruments APA100 - page 17

    Schematic 2-7 PCB Design 2.3 Schematic ...

  • Texas Instruments APA100 - page 18

    2-8 ...

  • Texas Instruments APA100 - page 19

    3-1 EVM Operation EVM Operation This chapter covers in detail the operation of the AP A100 EVM to guide the user in evaluating the audio power amplifier and in interfacing the AP A100 EVM to an audio input and power supply . T opic Page 3.1 Quick Start 3-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Texas Instruments APA100 - page 20

    Quick Start 3-2 3.1 Quick Start Follow these steps to use the AP A100 EVM. AP A100 audio input connection can be made via a phono jack (J1), or by sol- dering to its pins. The power supply and outputs can be connected with banana connectors or wires via screw terminals. Figure 3−1 shows numbered callouts for selected steps. Figure 3−1. Quick St ...

  • Texas Instruments APA100 - page 21

    Power−Up/Down Sequence 3-3 EVM Operation Power Up 6) Press and hold the RESET button (S1) 7) V erify correct voltage and input polarity , and set the external power supply to on . 8) Depress the RESET button (S1). The EVM begins operation. 9) Adjust the signal source level as needed. 10) Hold RESET button (S1) while powering down 3.2 Power−Up/D ...

  • Texas Instruments APA100 - page 22

    Changing the Gain 3-4 3.5 Changing the Gain The AP A100 EVM is set with a gain of 31.4 dB, but can be adjusted. The front-end has a gain of 4.4 dB (−1.667 V/V), and a back-end gain of 27 dB (−22.4 V/V), for a total of 31.4 dB (37.3 V/V). The back-end gain needs to be kept constant, because it is set by the control-loop feedback system with the ...

  • Texas Instruments APA100 - page 23

    4-1 T echnical Information T echnical Information This chapter goes into the details of the design of the 100-W amplifier . The design comprises the modulator , H-bridge, operational amplifier , feedback loop, LC filter , and thermal. T opic Page 4.1 Feedback System Design 4-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Texas Instruments APA100 - page 24

    Feedback System Design 4-2 4.1 Feedback System Design The AP A100 EVM uses feedback to lower distortion, increase supply ripple rejection, and make the gain not change with supply voltage. This section goes through the following steps to close the loop. 1) T a ke feedback at T AS51 1 1 outputs before the LC filter , so that it is unnec- cary to can ...

  • Texas Instruments APA100 - page 25

    Feedback System Design 4-3 T echnical Information operational amplifier (R22, R23, C20, C23, and C24) was eventually reduced from 400 kHz to 252 kHz to optimize performance; compensation for this is discussed later . Notice that in Figure 4−8, the switching frequency of each output is 250 kHz, but the dif ferential frequency is 500 kHz. The poles ...

  • Texas Instruments APA100 - page 26

    Feedback System Design 4-4 Figure 4−3. Open− and Closed−Loop Frequency Response With TP A2001D1 Pole and Canceling Zero Open Loop Gain Closed Loop Gain Fc = 40 kHz 0 Degrees −90 Degrees Phase Gain − dB Frequency − Hz 20 dB / Decade X F P0 F P0 * 10 F P0 10 X X X 80 kHz >400 kHz Now that the poles and zeros have been realized, the clo ...

  • Texas Instruments APA100 - page 27

    Feedback System Design 4-5 T echnical Information Th e closed−loop gain is set to 27 dB to allow enough gain from the 3−V signal to the A+ voltage range. This leaves sufficient low−frequency correction. Figure 4−4 shows the circuit used for the AP A100 feedback. Equation (2) shows the closed−loop response. Closed− loop gain + 45 R20 R18 ...

  • Texas Instruments APA100 - page 28

    Feedback System Design 4-6 Instead of calculating the bandwidth, PSPICE was used with a linearized circuit (see Figure 4−5) to simulate and adjust the component values to approximately 40-kHz bandwidth. Then, Equations 7 and 8 were used to set the poles and zeros. The first op amp (U1) in the simulation circuit of Figure 4−5 is the integrator; ...

  • Texas Instruments APA100 - page 29

    TP A2001D1 (Class-D Modulator) 4-7 T echnical Information Figure 4−6. PSPICE Simulation of Open−Loop Response f − Frequency − Hz T AS51 1 1 Output (dB) Integrator Output (dB) 200 100 −0 −100 −200 −300 100 1 k 10 k 100 k 1 M Phase ( 5 ) 4.2 TP A2001D1 (Class-D Modulator) The TP A2001D1 was chosen as an excellent performance, low-cost ...

  • Texas Instruments APA100 - page 30

    TP A2001D1 (Class-D Modulator) 4-8 Figure 4−7. TP A2001D1 Block Diagram _ + Gain Adj. _ + + _ cmv Gain Adj. Rs2 Rs1 _ + _ + Cint2 Cint1 _ + Deglitch Logic Deglitch Logic Comparator Integrator Pre-Amp Gate Drive Gate Drive TTL Input Buffers 2 SDZ Gain Biases and References Ramp Generators Startup Protection Logic OC Detect Thermal VDDok VDD VDD AG ...

  • Texas Instruments APA100 - page 31

    T AS51 1 1 (H-Bridge) 4-9 T echnical Information For more information concerning the TP A2001D1 operation and modulation scheme, see the TP A2001D1 data sheet http://focus.ti.com/docs/prod/folders/print/tpa2001d1.html 4.3 T AS51 1 1 (H-Bridge) The T AS51 1 1 converts the PWM signal from the 3-V peak-to-peak outputs of the T P A2001D1 to 18-V to 29. ...

  • Texas Instruments APA100 - page 32

    LC Filter 4-10 4.5 LC Filter The LC filter serves two purposes in this design. 1) Reduces EMI 2) Enables overcurrent (OC) protection. Th e outputs of the T AS51 1 1 are square waves with fast rise and fall times. The square waves produce harmonics up to 500 MHz. The speaker wire makes transmission lines for these frequencies. The LC filter attenuat ...

  • Texas Instruments APA100 - page 33

    Thermal 4-1 1 T echnical Information 4.6 Thermal The AP A100 thermal issues lie with the T AS51 1 1. The following thermal calculations and tables are taken from the T AS51 1 1 data sheet. The T AS51 1 1 is designed to be interfaced directly to a heatsink using a thermal interface compound (for example, W akefield Engineering type 126 thermal greas ...

  • Texas Instruments APA100 - page 34

    Thermal 4-12 As an indication of the importance of keeping the thermal grease layer thin, if the thermal grease layer increases to 0.002 inch thick, the required heatsink thermal resistance changes to 2.4 ° C/W . The large heatsink used for the AP A100 EVM is required for full output power sine waves over temperature. A smaller heatsink can be use ...

  • Texas Instruments APA100 - page 35

    5-1 Measured Results Measured Results This chapter shows the performance of the AP A100 reference design. An Audio Precision analyzer was used to produce the graphs in this chapter . T opic Page 5.1 T otal Harmonic Distortion + Noise 5-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 Output Power 5-4 . . . . . . . . . . . . . . . . ...

  • Texas Instruments APA100 - page 36

    T otal Harmonic Distortion + Noise 5-2 5.1 T otal Harmonic Distortion + Noise The AP A100 has excellent total harmonic distortion + noise (THD+N). Figure 5−1 and Figure 5−2 show the THD+N versus frequency , and Figure 5−3 and Figure 5−4 show THD+N vs output power . A 30-kHz bandwidth limit was used on the audio precision to limit switching ...

  • Texas Instruments APA100 - page 37

    T otal Harmonic Distortion + Noise 5-3 Measured Results Figure 5−3. AP A100 THD+N vs Output Power With 4- W Load 20 5 1 0.5 0.1 0.05 0.01 10 m 1 2 10 20 100 200 THD+N − T otal Harmonic Distortion + Noise − % P O − Output Power − W f = 1 kHz, PV DD = 15 V , 18 V , 20 V , 24 V , 28 V , 29.5 V Figure 5−4. AP A100 THD+N vs Output Power With ...

  • Texas Instruments APA100 - page 38

    Output Power 5-4 5.2 Output Power The AP A100 can output over 100 W into 4 Ω . The curves in Figure 5−5 and Figure 5−6 show the output power versus supply voltage. Figure 5−5. AP A100 Output Power vs Supply Voltage W ith 4- W Load 0 20 40 60 80 100 120 18 20 22 24 26 28 P O @ 10% THD P O @ 1% THD P O − Output Power − W V CC Supply V olt ...

  • Texas Instruments APA100 - page 39

    Efficiency 5-5 Measured Results 5.3 Efficiency The A P A100 is a highly ef ficient class-D audio power amplifier . The ef ficiency is greater than 85% efficient with 4- or 8- Ω load. The ef ficiency plot is shown in Figure 5−7. Figure 5−7. AP A100 Efficiency vs Output Power With 4- W Load 100 90 80 70 60 50 40 30 20 10 0 0 1 02 03 0 4 05 0 6 ...

  • Texas Instruments APA100 - page 40

    Gain and Phase Response 5-6 5.4 Gain and Phase Response Th e A P A100 is a closed−loop, class-D audio power amplifier with an LC output filter . The output filter and the 39-kHz loop bandwidth limit the bandwidth of the AP A100 reference design. The gain versus frequency curve is shown in Figure 5−8. The 4- Ω curve rolls off sooner than the 8 ...

  • Texas Instruments APA100 - page 41

    Supply Ripple Rejection 5-7 Measured Results 5.6 Supply Ripple Rejection The AP A100 uses a closed loop which keeps the gain from changing with supply voltage and improves the supply ripple rejection ratio (k SRR ) over an open−loop class-D amplifier . The supply ripple rejection ratio versus frequency curve is shown in Figure 5−9. Figure 5−9 ...

  • Texas Instruments APA100 - page 42

    5-8 ...

Manufacturer Texas Instruments Category Stereo Amplifier

Documents that we receive from a manufacturer of a Texas Instruments APA100 can be divided into several groups. They are, among others:
- Texas Instruments technical drawings
- APA100 manuals
- Texas Instruments product data sheets
- information booklets
- or energy labels Texas Instruments APA100
All of them are important, but the most important information from the point of view of use of the device are in the user manual Texas Instruments APA100.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Texas Instruments APA100, service manual, brief instructions and user manuals Texas Instruments APA100. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Texas Instruments APA100.

Similar manuals

A complete manual for the device Texas Instruments APA100, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Texas Instruments APA100 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Texas Instruments APA100.

A complete Texas Instruments manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Texas Instruments APA100 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Texas Instruments APA100, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Texas Instruments APA100, that we can find in the current document
3. Tips how to use the basic functions of the device Texas Instruments APA100 - which should help us in our first steps of using Texas Instruments APA100
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Texas Instruments APA100
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Texas Instruments APA100 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Texas Instruments APA100?

Use the form below

If you did not solve your problem by using a manual Texas Instruments APA100, ask a question using the form below. If a user had a similar problem with Texas Instruments APA100 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)