English dropdown-ico

Manual Miller Electric 145 DX

56 pages 2.32 mb
Download

Go to site of 56

Summary
  • Miller Electric 145 DX - page 1

    Blue Star 145 Processes Description Stick (SMAW) W elding Engine Driven Welding Generator OM-4417 210 403C 2005 − 10  Blue Star 145 DX  File: Engine Drive V isit our website at www.MillerWelds.com ...

  • Miller Electric 145 DX - page 2

    Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog or individual specification sheets. T o locate your nearest distributor or service agency call 1-800-4-A-Miller , or visit us at www .Mille ...

  • Miller Electric 145 DX - page 3

    T ABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2. Arc W elding Hazards 1 . . . . . . . ...

  • Miller Electric 145 DX - page 4

    ...

  • Miller Electric 145 DX - page 5

    OM-4417 Page 1 SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING rom _nd_3/05  W arning: Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols.  Marks a special saf ...

  • Miller Electric 145 DX - page 6

    OM-4417 Page 2 W elding on closed containers, such as tanks, drums, or pipes, can cause them to blow up. Sparks can fly of f from the welding arc. The flying sparks, hot workpiece, and hot equipment can cause fires and burns. Accidental contact of electrode to metal objects can cause sparks, explosion, overheating, or fire. Check and be sure the ar ...

  • Miller Electric 145 DX - page 7

    OM-4417 Page 3 STEAM AND HOT COOLANT can burn.  If possible, check coolant level when engine is cold to avoid scalding.  Always check coolant level at overflow tank, if pres- ent on unit, instead of radiator (unless told otherwise in maintenance section or engine manual).  If the engine is warm, checking is needed, and there is no overflow ...

  • Miller Electric 145 DX - page 8

    OM-4417 Page 4 READ INSTRUCTIONS.  Use only genuine MILLER/Hobart replacement parts.  Perform engine and air compressor (if applicable) maintenance and service according to this manual and the engine/air compressor (if applicable) manu- als. H. F . RADIA TION can cause interference.  High-frequency (H.F .) can interfere with radio naviga- ...

  • Miller Electric 145 DX - page 9

    OM-4417 Page 5 SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE A V ANT UTILISA TION rom_fre 3/05  Avertissement: Protégez vous et les autres des blessures − lisez et suivez ces précautions. 2-1. Signification des symboles Signifie Mise en garde ! Soyez vigilant ! Cette procédure présente des risques de danger ! Ceux-ci sont identifiés par ...

  • Miller Electric 145 DX - page 10

    OM-4417 Page 6 Le soudage effectué sur des conteneurs fermés tels que des réservoirs, tambours ou des conduites peut provoquer leur éclatement. Des étincelles peuvent être projetées de l’arc de soudure. La projection d’étincelles, des pièces chaudes et des équipements chauds peut provoquer des incendies et des brûlures. Le contact ac ...

  • Miller Electric 145 DX - page 11

    OM-4417 Page 7  Si le moteur est chaud et que le liquide doit être vérifié, opérer comme suivant.  Mettre des lunettes de sécurité et des gants, placer un torchon sur le bouchon du radiateur .  Dévisser le bouchon légèrement et laisser la vapeur s’échapper avant d’enle- ver le bouchon. LES ACCUMULA TIONS DE GAZ ris- quent de ...

  • Miller Electric 145 DX - page 12

    OM-4417 Page 8 LIRE LES INSTRUCTIONS.  Utiliser seulement les pièces de rechange d’origine.  Ef fectuer la maintenance du moteur et du compresseur (s i applicable) suivant ce manuel et le manuel du moteur/ compresseur (si applicable). LE RA YONNEMENT HAUTE FRÉ- QUENCE (H.F .) risque de provoquer des interférences.  Le rayonnement haut ...

  • Miller Electric 145 DX - page 13

    OM-4417 Page 9 SECTION 3 − DEFINITIONS 3-1. Symbol Definitions Engine Choke Read Operator ’s Manual A Amperes V V olts Engine Oil Fuel Battery (Engine) Engine Positive Negative Alternating Current (AC) Output h Hours s Seconds T ime Protective Earth (Ground) Circuit Protector T emperature SECTION 4 − SPECIFICA TIONS 4-1. W eld, Power , And En ...

  • Miller Electric 145 DX - page 14

    OM-4417 Page 10 4-2. Dimensions, Weights, And Operating Angles Dimensions Height 22-3/4 in (578 mm) D Width 22-3/4 in (577 mm) D Depth 31-5/8 in (803 mm)  Do not exceed tilt angles or engine could A 31-5/8 in (803 mm) B  Do not e x ceed tilt angles or engine co u ld be damaged or unit could tip. B 10-9/16 in (268 mm)  Do not move or operat ...

  • Miller Electric 145 DX - page 15

    OM-4417 Page 1 1 4-4. Fuel Consumption 220 637 DC WELD AMPERES A T RA TED DUTY CYCLE US Gal./Hr . 0 25 50 75 100 125 150 175 200 0.00 0.20 0.40 0.60 0.80 1.00 IDLE AUXILIARY POWER KW A T 100% DUTY CYCLE US Gal./Hr . 0 12 345 6 0.00 0.20 0.40 0.60 0.80 1.00 IDLE ...

  • Miller Electric 145 DX - page 16

    OM-4417 Page 12 Continuous W elding 4-5. Duty Cycle 220 625 − A Duty cycle is the percentage of 10 minutes that unit can weld at rated load without overheating.  Exceeding duty cycle can damage unit and void warranty . 100% Duty Cycle at 80 Amperes CC/DC 20% Duty Cycle at 145 Amperes CC/DC % DUTY CYCLE WELD AMPERES 0 0 10 20 20 30 40 40 50 60 ...

  • Miller Electric 145 DX - page 17

    OM-4417 Page 13 SECTION 5 − INST ALLA TION 5-1. Installing W elding Generator Ref 151 556 / Ref. 800 652 / 803 594-B / S-0854 18 in (460 mm) 18 in (460 mm) 18 in (460 mm) 18 in (460 mm) 18 in (460 mm) OR Movement Airflow Clearance Location Shown with optional running gear.  Always securely fasten welding generator onto transport vehicle or tra ...

  • Miller Electric 145 DX - page 18

    OM-4417 Page 14 5-3. Grounding Generator When Supplying Building Systems GND/PE 1 2 Use ground device as stated in electrical codes. 2 3 800 576-B 1 Equipment Grounding T erminal 2 Grounding Cable Use #10 AWG or larger insulated copper wire. 3 Ground Device  Ground generator to sys- tem earth ground if supply- ing power to a premises (home, shop ...

  • Miller Electric 145 DX - page 19

    OM-4417 Page 15 5-5. Engine Prestart Checks − DX Model 803 595-B Full Gasoline 1/2 in (13 mm) Check all fluids daily . Engine must be cold and on a level surface. Unit is shipped with 10W30 engine oil. 1 Fuel V alve Open valve.  Close fuel valve before moving unit or carburetor may flood and make starting difficult. Fuel Add fresh fuel before ...

  • Miller Electric 145 DX - page 20

    OM-4417 Page 16 5-7. Connecting T o W eld Output T erminals 803 596 − B / 803 778-A 1 Positive (+) W eld Output T erminal 2 Negative ( − ) W eld Output T erminal For Direct Current Electrode Posi- tive (DCEP), connect work cable to Negative ( − ) terminal and electrode holder to Positive (+) terminal. For Direct Current Electrode nega- tive ( ...

  • Miller Electric 145 DX - page 21

    OM-4417 Page 17 Notes 16 Gauge (.063 in) 22 Gauge (.031 in) 24 Gauge (.025 in) 20 Gauge (.037 in) 18 Gauge (.050 in) 14 Gauge (.078 in) 1/8 in (.125 in) 3/16 in (.188 in) 1/4 in (.25 in) 5/16 in (.313 in) 3/8 in (.375 in) 1/2 in (.5 in) MA TERIAL THICKNESS REFERENCE CHART ...

  • Miller Electric 145 DX - page 22

    OM-4417 Page 18 SECTION 6 − OPERA TING THE WELDING GENERA T OR 6-1. Controls (Standard Models) (See Section 6-2) 803 956 − B / 803 594 − B / 218 610 4 1 6 3 5 2 ...

  • Miller Electric 145 DX - page 23

    OM-4417 Page 19 6-2. Description Of Controls (Standard Models) (See Section 6-1 ) 1 Engine Switch Use switch to control ignition circuit. T urn switch to On position when starting engine. Turn switch to Off position to stop engine. En- gine cannot be started with switch in the Off position. Engine stops if oil level is too low . Engine can- not be ...

  • Miller Electric 145 DX - page 24

    OM-4417 Page 20 6-3. Controls (DX Models) (See Section 6-4) 803 596 − A / 803 595 − A / 218 610 1 8 7 3 5 4 6 2 ...

  • Miller Electric 145 DX - page 25

    OM-4417 Page 21 6-4. Description Of Controls (DX Models) (See Section 6-3 ) 1 Engine Switch Use switch to control ignition circuit. T urn switch t o Start position for electric start. Turn switch to On position to start engine using starter ha ndle (recoil). T urn switch to Off posi- tion to stop engine. 2 Low Oil Level Light Light goes on and engi ...

  • Miller Electric 145 DX - page 26

    OM-4417 Page 22 SECTION 7 − OPERA TING AUXILIAR Y EQUIPMENT Set Current control to maximum for full generator power output at AC receptacles. NOTE 7-1. Generator Power Panel Receptacles  If unit does not have GFCI recep- tacles, use GFCI-protected exten- sion cord.  Generator power decreases as weld current increases . 1 240 V AC Receptacle ...

  • Miller Electric 145 DX - page 27

    OM-4417 Page 23 SECTION 8 − MAINTENANCE Follow the storage procedure in the engine owner ’s manual if the unit will not be used for an extended period. NOTE 8-1. Routine Maintenance  Stop engine before maintaining.  S ee Engine Manual and Maintenance Label for important start-up, service, and storage information. Service engine more often ...

  • Miller Electric 145 DX - page 28

    OM-4417 Page 24 8-2. Servicing Air Cleaner aircleaner6 9/00 − 803 404  Stop engine.  Do not run engine without a ir cleaner or with dirty element. 1 Precleaner 2 Paper Element  Do not wash paper element or clean with compressed air. Remove cover . Was h precleaner with soap and wa- ter solution. Allow precleaner to air dry completely . D ...

  • Miller Electric 145 DX - page 29

    OM-4417 Page 25 8-3. Adjusting Engine Speed (Standard Models Only) 803 594-B T ools Needed: 3750 ± 30 rpm (62 Hz) After tuning engine, check engine speed. See table for proper no load speed. If necessary , adjust speed as follows: Start engine and run until warm. 1 Adjustment Screw T o increase speed, turn screw in (clockwise). T o decrease speed, ...

  • Miller Electric 145 DX - page 30

    OM-4417 Page 26 8-4. Adjusting Engine Speed (DX Models Only) 803 595 − B 2500 ± 100 rpm (42 Hz) 3750 ± 30 rpm (62 Hz) T ools Needed: After tuning engine, check engine speed. See table for proper no load speed. If necessary , adjust speed as follows: Start engine and run until warm. Set Weld Output Control to Max. W eld/Power Speed Adjustment 1 ...

  • Miller Electric 145 DX - page 31

    OM-4417 Page 27 SECTION 9 − TROUBLESHOOTING 9-1. T roubleshooting A. Welding T rouble Remedy No weld output or generator power out- put at ac receptacles. Be sure all equipment is disconnected from receptacles when starting unit. Have Factory Authorized Service Agent check brushes, slip rings, rotor , stator , integrated rectifier SR2, and Weld O ...

  • Miller Electric 145 DX - page 32

    OM-4417 Page 28 T rouble Remedy Low output at generator power ac receptacles. Check W eld Output control setting. Check engine speed, and adjust if necessary (see Section 8-3 or 8-4). Open circuit voltage is reduced as engine speed drops. Erratic output at generator power ac receptacles Check fuel level. receptacles. Have Factory Authorized Service ...

  • Miller Electric 145 DX - page 33

    OM-4417 Page 29 SECTION 10 − ELECTRICAL DIAGRAMS 226 737-A Figure 10-1. Circuit Diagram For Standard Models ...

  • Miller Electric 145 DX - page 34

    OM-4417 Page 30 226 738-A Figure 10-2. Circuit Diagram for DX Models ...

  • Miller Electric 145 DX - page 35

    OM-4417 Page 31 SECTION 1 1 − GENERA T OR POWER GUIDELINES The views in this section are intended to be representative of all engine-driven welding generators. Your unit may differ from those shown. NOTE 1 1-1. Selecting Equipment gen_pwr 1 1/02 − Ref. ST-159 730 / ST -800 577 1 Generator Power Receptacles − Neutral Bonded T o Frame 2 3-Prong ...

  • Miller Electric 145 DX - page 36

    OM-4417 Page 32 1 1-3. Grounding When Supplying Building Systems ST-800 576-B 1 Equipment Grounding T erminal 2 Grounding Cable Use #10 AWG or larger insulated copper wire. 3 Ground Device  Ground generator to system earth ground if supplying power to a premises (home, shop, farm) wiring system. GND/PE 1 2 Us e ground device as stated in electri ...

  • Miller Electric 145 DX - page 37

    OM-4417 Page 33 1 1-5. Approximate Power Requirements For Industrial Motors Industrial Motors Rating Starti ng W atts Running W atts Split Phase 1/8 HP 800 300 1/6 HP 1225 500 1/4 HP 1600 600 1/3 HP 2100 700 1/2 HP 3175 875 Capacitor Start-Induction Run 1/3 HP 2020 720 1/2 HP 3075 975 3/4 HP 4500 1400 1 HP 6100 1600 1-1/2 HP 8200 2200 2 HP 10550 28 ...

  • Miller Electric 145 DX - page 38

    OM-4417 Page 34 1 1-7. Approximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running W atts Hand Drill 1/4 in 350 350 3/8 in 400 400 1/2 in 600 600 Circular Saw 6-1/2 in 500 500 7-1/4 in 900 900 8-1/4 in 1400 1400 T able Saw 9 in 4500 1500 10 in 6300 1800 Band Saw 14 in 2500 1 100 Bench Grinder 6 in 1720 720 8 in ...

  • Miller Electric 145 DX - page 39

    OM-4417 Page 35 1 1-8. Power Required T o Start Motor S-0624 1 Motor Start Code 2 Running Amperage 3 Motor HP 4 Motor V oltage T o find starting amperage: Step 1: Find code and use table to find kV A/HP . If code is not listed, multiply running amperage by six to find starting amperage. Step 2 : Find Motor HP and V olts. Step 3: Determine starting ...

  • Miller Electric 145 DX - page 40

    OM-4417 Page 36 1 1-10. T ypical Connections T o Supply Standby Power  Have only qualified persons perform these connections according to all applicable codes and safety practic- es.  Properly install and ground this equipment according to its Owner ’s Manual and national, state, and local codes.  Customer -supplied equipment is re- quir ...

  • Miller Electric 145 DX - page 41

    OM-4417 Page 37 1 1-1 1. Selecting Extension Cord (Use Shortest Cord Possible) Cord Lengths for 120 V olt Loads  If unit does not have GFCI receptacles, use GFCI-protected extension cord. Maximum Allowable Cord Length in ft (m) for Conductor Size (A WG)* Current (Amperes) Load (W atts) 4 6 8 10 12 14 5 600 350 (106) 225 (68) 137 (42) 100 (30) 7 ...

  • Miller Electric 145 DX - page 42

    OM-4417 Page 38 SECTION 12 − STICK WELDING (SMA W) GUIDELINES 12-1. Stick Welding Procedure stick 12/96 − ST-151 593  W eld current starts when electrode touches work- piece.  W eld current can damage electronic parts in vehicles. Disconnect both battery cables before welding on a vehicle. Pl ac e wo rk c lam p as close to the weld as pos ...

  • Miller Electric 145 DX - page 43

    OM-4417 Page 39 12-2. Electrode and Amperage Selection Chart Ref. S-087 985-A 3/32 1/8 5/32 3/16 7/32 1/4 1/16 5/64 3/32 1/8 5/32 3/16 7/32 1/4 3/32 1/8 5/32 3/16 7/32 1/4 3/32 1/8 5/32 3/16 7/32 1/4 3/32 1/8 5/32 3/16 7/32 1/4 3/32 1/8 5/32 3/16 3/32 1/8 5/32 6010 & 601 1 6013 7014 7018 7024 Ni-Cl 308L 50 100 150 200 250 300 350 400 450 ELECTR ...

  • Miller Electric 145 DX - page 44

    OM-4417 Page 40 12-5. Positioning Electrode Holder S-0060 90 ° 90 ° 10 ° -30 ° 45 ° 45 ° GROOVE WELDS FILLET WELDS End V iew of Work Angle Sid e V iew of Electrode Angle End V iew of Work Angle S ide View of Electrode Angle 10 ° -30 ° 12-6. Poor Weld Bead Characteristics S-0053-A 1 Large Spatter Deposits 2 Rough, Uneven Bead 3 Slight Crater ...

  • Miller Electric 145 DX - page 45

    OM-4417 Page 41 12-8. Conditions That Affect W eld Bead Shape Weld bead shape is affected by electrode angle, arc length, travel speed, and thickness of base metal. NOTE S-0061 ELECTRODE ANGLE ARC LENGTH TRA VEL SPEED Slow Normal Fast 10 ° - 30 ° Drag T oo Short Normal T o o Long Spatter Angle T oo Small Angle T oo Large Correct Angle 12-9. Elect ...

  • Miller Electric 145 DX - page 46

    OM-4417 Page 42 12-10. Butt Joints S-0662 1 T ack Welds Prevent ed ge s o f j oint from drawing together ahead of electrode by tack welding the materials in position be- fore final weld. 2 Square Groove W eld Good for materials up to 3/16 in (5 mm) thick. 3 Single V -Groove Weld Good for materials 3/16 − 3/4 in (5-19 mm) thick. Cut bevel with oxy ...

  • Miller Electric 145 DX - page 47

    OM-4417 Page 43 12-13. W eld T est S-0057-B 1 V ise 2 W e ld Joint 3 Hammer Strike weld joint in direction shown. A good weld bends over but does not break. 2 T o 3 in 1/4 in 3 2 1 2 T o 3 in 3 2 1 (51-76 mm) (6.4 mm) (51-76 mm) 12-14. T roubleshooting − Porosity Porosity − small cavities or holes resulting from gas pockets i n weld metal. Poss ...

  • Miller Electric 145 DX - page 48

    OM-4417 Page 44 12-16. T roubleshooting − Incomplete Fusion Incomplete Fusion − failure of weld metal to fuse completely with base metal or a preceeding weld bead. Possible Causes Corrective Actions Insuf ficient heat input. Increase amperage. Select larger electrode and increase amperage. Improper welding technique. Place stringer bead in prop ...

  • Miller Electric 145 DX - page 49

    OM-4417 Page 45 12-19. T roubleshooting − Burn-Through Burn-Through − weld metal melting completely through base metal resulting in holes where no metal remains. Possible Causes Corrective Actions Excessive heat input. Select lower amperage. Use smaller electrode. Increase and/or maintain steady travel speed. 12-20. T roubleshooting − W avine ...

  • Miller Electric 145 DX - page 50

    OM-4417 Page 46 SECTION 13 − P ARTS LIST 803 795 − B  Hardware is common and not available unless listed. 1 2 3 4 5 6 7 8 10 11 13 14 15 23 24 29 30 31 32 33 2 34 35 36 37 39 38 9 12 28 27 26 25 22 21 20 19 17 18 16 Figure 13-1. Main Assembly Standard Model ...

  • Miller Electric 145 DX - page 51

    OM-4417 Page 47 Description Part No. Dia. Mkgs. Item No. Figure 13-1. Main Assembly (Standard Model) Quantity 1A C − Z 218767 Reactor 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 099255 T erminal, Pwr Output Neutral 2 . . . . . . . . . . . . . . . . . . ...

  • Miller Electric 145 DX - page 52

    OM-4417 Page 48 803 797-C  Hardware is common and not available unless listed. 59 1 2 3 4 5 6 7 8 10 11 16 17 21 22 23 24 25 13 33 34 35 37 38 39 40 45 46 48 49 50 51 52 53 54 55 56 57 58 14 15 36 9 47 20 19 18 12 52 26 28 27 29 30 31 32 42 43 44 41 Figure 13-2. Main Assembly DX Model Description Part No. Dia. Mkgs. Item No. Figure 13-2. Main As ...

  • Miller Electric 145 DX - page 53

    OM-4417 Page 49 Description Part No. Dia. Mkgs. Item No. Figure 13-2. Main Assembly (Continued) Quantity 15 221007 Bracket,Support Fuel T ank 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 223079 T ank, Fuel 5.0 Gal 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Miller Electric 145 DX - page 54

    OM-4417 Page 50 ...

  • Miller Electric 145 DX - page 55

    Warranty Questions? Call 1-800-4-A-MILLER for your local Miller distributor. miller_warr 1/05 Y o ur distributor also gives you ... Service Y ou always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours. Support Need fast answers to the tough welding questions? Contact your distributor . The expertise ...

  • Miller Electric 145 DX - page 56

    PRINTED IN USA © 2005 Miller Electric Mfg. Co. 10/05 Miller Elect ric Mfg. Co. An Illinois T ool W orks Co mpan y 1635 West S pencer S treet Applet on, WI 5 4914 US A International He adquarte rs − USA USA Phone: 920-735-4505 Aut o-At tended USA & Canada F AX : 920-735-4134 Int ernati onal F A X: 920-735-4125 European Headqua rters − Unite ...

Manufacturer Miller Electric Category Portable Generator

Documents that we receive from a manufacturer of a Miller Electric 145 DX can be divided into several groups. They are, among others:
- Miller Electric technical drawings
- 145 DX manuals
- Miller Electric product data sheets
- information booklets
- or energy labels Miller Electric 145 DX
All of them are important, but the most important information from the point of view of use of the device are in the user manual Miller Electric 145 DX.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Miller Electric 145 DX, service manual, brief instructions and user manuals Miller Electric 145 DX. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Miller Electric 145 DX.

Similar manuals

A complete manual for the device Miller Electric 145 DX, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Miller Electric 145 DX by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Miller Electric 145 DX.

A complete Miller Electric manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Miller Electric 145 DX - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Miller Electric 145 DX, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Miller Electric 145 DX, that we can find in the current document
3. Tips how to use the basic functions of the device Miller Electric 145 DX - which should help us in our first steps of using Miller Electric 145 DX
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Miller Electric 145 DX
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Miller Electric 145 DX in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Miller Electric 145 DX?

Use the form below

If you did not solve your problem by using a manual Miller Electric 145 DX, ask a question using the form below. If a user had a similar problem with Miller Electric 145 DX it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)