Manual Compaq iP-25E

48 pages 2.17 mb
Download

Go to site of 48

Summary
  • Compaq iP-25E - page 1

    A Proposal f or Ne w Presentations Intellig ent Pr ojector User’ s Manual iP-25E English Deutsch Français Español Italiano ...

  • Compaq iP-25E - page 2

    E-2 Thank you f or your purchase of an A VIO product. Please read this manual carefully in order to use the projector properly . After reading this, please k eep it in a safe place together with the warr anty sheet. Features of the iP-25E •V ery versatile five-in-one projector . A projector for the m ultimedia age . 1. Projection of documents, ca ...

  • Compaq iP-25E - page 3

    E-3 W ARNING ● If a fault occurs: • If you detect smok e, or a strange smell or sound, immediately disconnect the pow er cable. It is dangerous to continue using the projector after a f ault occurs. Return the projector to the dealer where it was purchased f or repair . ● Av oid placing the projector near dangerous substances. • Make sure t ...

  • Compaq iP-25E - page 4

    E-4 Safety Precautions CAUTION •I nstallation •A v oid installing the projector in places where it ma y be exposed to: -S trong vibr ations - Soot or steam -D irect sunlight or near a heater (35 ° C/95 ° F or higher) -H igh humidity or dust - Extreme cold (0 ° C/32 ° F or lower) - Strong magnetic or electric field generated from a nearby ap ...

  • Compaq iP-25E - page 5

    E-5 • Lamp implosion •A DC type Super High pressure lamp is used in this projector and it is r are for the lamp to e xplode dur ing use. The unit is al so designed to forcib ly tur n off the lamp because there is a high possibility that the lamp will break if it is used bey ond the lamp usage of 2000 hours (Ref er to pages E-42 and E-44). Note ...

  • Compaq iP-25E - page 6

    E-6 T able of Contents Safety Precautions ................................................. E-3 A Check of the Supplied Items and the Names of the P ar ts .............................. E-7 Supplied P ar ts Chec k ............................................... E-7 Names and Functions of the P ar ts (Projector) ......... E-8 Names and Functions of ...

  • Compaq iP-25E - page 7

    E-7 User's manual A Check of the Supplied Items and the Names of the Parts Supplied P ar ts Check Please check that the supplied parts are included. Lens cap iP-25E Projector Replacement air filter Pow er cable (3 m) Remote control Coin-type lithium battery: CR2025 (Inside the remote control) Pull out the sheet bef ore use. iP-25E User’ s Ma ...

  • Compaq iP-25E - page 8

    E-8 Remote control IR sensor Lens cap Focus adjustment ring Tu rn this to adjust the focus. See P age E-22. Projection lens The image is projected from here. * Be sure to remov e the lens cap bef ore projecting. Zoom lever Tu rn this to adjust the screen siz e. See P age E-22. Document cover The document or printed mater ial to be read is placed un ...

  • Compaq iP-25E - page 9

    E-9 A Check of the Supplied Items and the Names of the P ar ts Speaker (2 W , monaur al) Theft prevention loc k Please see the Note below . Remote control IR sensor Document reading area The document or printed material that you wish to project in the OHP mode is placed here. See P age E-30. Po wer input connector Plug in the power cab le here. See ...

  • Compaq iP-25E - page 10

    E-10 Names and Functions of the P ar ts (Input Connectors) 1. T est (maintenance) connector This special connector is used at the time of maintenance and factory tests. It cannot be used for other connections . 2. Personal computer audio input connector This audio input connector is f or use with the personal com- puter (Stereo suppor ted). See P a ...

  • Compaq iP-25E - page 11

    E-11 Names and Functions of the P ar ts (Operation P anel) 5. INPUT SELECT Buttons These buttons select the input source . OHP → PC → VIDEO → OHP → ... See P age E-23. 5. PORTRAIT/TRANSFER Button During OHP selection: Changes the orientation of the pro- jection screen. Changed screens are displa yed in conjunc- tion with the width. See P ag ...

  • Compaq iP-25E - page 12

    E-12 Names and Functions of the P ar ts (Remote Contr ol) 1. POWER Button Switches the power of the projector on or off (standb y mode). • Only this button is eff ective when the projection lamp is off . See P age E-21. 2. MUTE Button T emporarily blanks the projection screen without s witching off the lamp . One more press causes the screen to r ...

  • Compaq iP-25E - page 13

    E-13 A Check of the Supplied Items and the Names of the P ar ts Operation of the Remote Contr ol • Please use the remote control within a range of about 7 m from the remote control IR sensor of the projector (located at both the front and rear) and within an angle of 10 degrees to the left and 10 deg rees to the r ight. Note that this distance ma ...

  • Compaq iP-25E - page 14

    E-14 Pr ocedure Up to Pr ojection 1 Consideration of placement location and screen size Determine the screen and projector setup location. Set the projector on a strong and stable , lev el platform. 2 Connections with input equipment Connect your personal computer/video equipment. Connections with the P ersonal Computer → See P age E-16 Connectio ...

  • Compaq iP-25E - page 15

    E-15 Please use the f ollowing diagrams to determine the screen displa y size and the type of screen required for an y given projector location. Projection distances that will be in f ocus will be 1.3 m (4.3 feet) to 11.3 m (37.0 f eet) from the front of the lens. Please arrange the setup within this r ange. Setup Location • Do not place the proj ...

  • Compaq iP-25E - page 16

    E-16 Connections with P ersonal Computer s iP-25 To the RGB output connector of the personal computer To the audio output connector of the personal computer To the USB connector of the personal computer Plug in the connection cable and f asten with the screws Connection Precautions •T o protect this projector and the equipment to be connected, s ...

  • Compaq iP-25E - page 17

    E-17 Connections with the P ersonal Computer Connecting Macintosh Computers • Attach the supplied (RGB+USB) cable if when the monitor output is a VGA port (mini D-SUB 15-pin). • An optional Apple video adapter cable is required when the monitor output is a video port or D VI por t. • Please do not mak e a USB connection because iP Viewer does ...

  • Compaq iP-25E - page 18

    E-18 Connections with the P ersonal Computer Please check the matters described below when the image of the personal computer is not projected or when there is projection but the image is not correct. ● The ima g e is not projected When the external output signal from the personal computer is not input to the iP-25E, "No signal being input&q ...

  • Compaq iP-25E - page 19

    E-19 Signal Name Resolution Horizontal Frequency Vertical Frequency Supported (Horizontal ⳯ Vertical) (kHz) (Hz) NTSC RGB – – 15.7 60 No PAL/SECAM RGB – – 15.6 50 No PC-98 Normal* 640 400 24.8 56 Yes PC-98 Hi 640 400 31.5 70 Yes VGA-GR1 640 480 31.5 60 Yes VGA-GR2* 640 400 31.5 70 Yes VGA-GR3* 640 350 31.5 70 Yes VGA-TX1* 720 400 31.5 70 ...

  • Compaq iP-25E - page 20

    E-20 Connections with V ideo Equipment The video of a video tape deck or D VD player is projected onto a lar g e screen. NO TE: •W hen both Video and S-video connections hav e been made, S-video will be given priority for displa y . •W hen a video signal hav e a lot of noise, the image may be displa yed in monochrome. Should this occur , make a ...

  • Compaq iP-25E - page 21

    E-21 Switch Off the P ower The projector is no w able to make a projection. 3 Switch on the po wer of the connected equipment Connection of the Power Cable and On/Of f Switching Switch On the P ower 1 Connect the power cable The projector will enter the standby mode and the ON/ST ANDBY LED will light in red. To wall outlet. 2 Press the PO WER butto ...

  • Compaq iP-25E - page 22

    E-22 Adjustment of the Pr ojection Image Adjust the projection image to the screen. Adjusting the Pr ojection Image • When the image is shifted to the left or right, mov e the projector hor izontally . (Align the center of the screen with the center of the projector lens.) • When the image is shifted up or down, use the tilt f oot to adjust the ...

  • Compaq iP-25E - page 23

    E-23 Regular Operation Operation with the Projector Press the PORTRAIT b utton. Operation with the Remote Contr ol Press the PORTRAIT b utton. A B C This section describes the use of direct operation using the projector and remote control buttons . Please see the items on P age E-32 "Menu Operation Method" and P age E-35 "Menu Descr ...

  • Compaq iP-25E - page 24

    E-24 A B C To view the portion that has been cut off Operation with the Projector Press the SCROLL ( 왖왔 ) b uttons and scroll the projec- tion image up or down. Operation with the Remote Control Press the SCROLL ( 왖왔 ) b uttons and scroll the projec- tion image up or down. NO TE: When the orientation of the projection image is changed, ev e ...

  • Compaq iP-25E - page 25

    E-25 Regular Operation Moving the Screen Operation with the Pr ojector Press the SCROLL ( 왖왔왗왘 ) b uttons. Operation with the Remote Contr ol Press the SCROLL ( 왖왔왗왘 ) b uttons. Mov ement is possible in 4 directions (up , down, left, and right). Adjusting the Brightness NO TE: Once the br ightness adjustment bar has been display ed, ...

  • Compaq iP-25E - page 26

    E-26 12 32 32 12 34 56 78 9 10 11 12 13 14 15 16 12 34 56 78 9 10 11 12 13 14 15 16 During OHP Input Pressing the FREEZE/CAPTURE button captures the OHP image that is currently being projected and sav es it as an image file. Captured images are automatically stored in the internal memory as OHP histor y images f or up to 32 pages. The projected ima ...

  • Compaq iP-25E - page 27

    E-27 Viewing captured ima g es Operation with the Projector A list displa y of captured images is not av ailable from the operation panel of the projector . Operation with the Remote Contr ol Press the THUMBNAIL button. Full-screen Display of Thumbnail Images Operation with the Projector A full-screen display of captured images is not a vailab le f ...

  • Compaq iP-25E - page 28

    E-28 T ransferring Captured Images When connection is made with a USB cable , histor y images can be transf erred to the per- sonal computer . Please switch the input to "PC" and press the data TRANSFER button. Operation with the Pr ojector Press the TRANSFER button. NO TE: Please see the attached “iP Viewer Program Quic k Reference” ...

  • Compaq iP-25E - page 29

    E-29 Operation with the Pr ojector The ability to turn on and tur n off the pointer is not av ail- able from the oper ation panel of the projector . Operation with the Remote Contr ol Press the POINTER/SET button. One more press of the POINTER/SET b utton while the pointer is display ed will turn off the pointer display . Moving the P ointer Operat ...

  • Compaq iP-25E - page 30

    E-30 Method of OHP Operation The maximum reading size of documents and printed material is 216 mm high by 288 mm wide. Consequently , when A4 paper (210 mm high and 297.5 mm wide) is placed on the projector , reading will be as illustrated in the diagr am below (which depicts the area that can be projected as the por tion with diagonal lines). Atta ...

  • Compaq iP-25E - page 31

    E-31 Menu Configuration Po i n ter • Screen Image adjustment Settings OHP/ PC / VIDEO Common During OHP Input OHP / PC / VIDEO Common During PC Input During VIDEO Input The adjustment/setting items and content will diff er depending on the input selection and the per mitted inf or mation will be displa yed on the menu f or that input mode. During ...

  • Compaq iP-25E - page 32

    E-32 Menu Operation Method Names and Functions of the Buttons Used in Menu Operation SCR OLL 왖왔왗왘 Buttons Used in the selection of menu names and item names, and to set and ad- just item contents. Names and Functions of the Menu P ar ts Sub menu icon When an item containing this icon is selected, there is a change to the sub menu. Retur ns ...

  • Compaq iP-25E - page 33

    E-33 Method of Menu Operation Menu Operation Method This section describes the actual operation method. Adjustment of [K eystone] using the remote control is provided as an e xample. 1 Press the MENU b utton and display the menu 2 Select [Settings] with the SCR OLL 왗왘 buttons Each press of the SCR OLL 왘 b utton switches the menu one step in t ...

  • Compaq iP-25E - page 34

    E-34 4 Press the POINTER/SET Button Switches the menu to the sub menu (i.e ., the K eystone adjustment menu). Menu Operation Method 5 Make the adjustment with the SCR OLL 왗왘 b uttons while checking the pr ojection image SCROLL 왗 button: Each press causes the numerical value to decrease. (The lower portion of the projection im- age becomes nar ...

  • Compaq iP-25E - page 35

    E-35 Pntr setting This selects the shape, color , and size of the pointer . 䢇 P ointer shape ................. Selects the shape of the pointer from 2 types. 䢇 P ointer color ................... Selects the color of the pointer from amongst 3 types (i.e., red, white, and bl ue). 䢇 P ointer size .................... The size of the pointer can ...

  • Compaq iP-25E - page 36

    E-36 When PC input has been selected 䢇 Contrast ......................... Adjusts the contrast of the projected image in the range of -50 to 50. 䢇 Brightness ...................... Adjusts the br ightness of the pro- jected image in the range of -50 to 50. 䢇 Red (Red color adjustment) ....... Adjusts the deepness of the red color in the range ...

  • Compaq iP-25E - page 37

    E-37 When VIDEO input has been selected 䢇 Contrast ......................... Adj usts the contrast of the projected image in the range of -50 to 50. 䢇 Brightness ...................... Adjusts the br ightness of the pro- jected image in the range of -50 to 50. 䢇 Color .............................. Adjusts the deepness of the color in the ran ...

  • Compaq iP-25E - page 38

    E-38 Menu Description Settings This performs settings related to the projector unit or while the projector is in use. 䢇 Lamp usage time ........... Displays the usage time of the lamp . "Replacement of the Lamp Unit" → See P age E-42 䢇 Input signal ..................... The name of the currently selected input is displa yed. Setting ...

  • Compaq iP-25E - page 39

    E-39 䢇 Projection mode ............. Selects the projection system of the projector from between F ront (front projection) and Rear (rear projec- tion). 䢇 Economy mode .............. ON (Economy mode): The brightness of the lamp will be appro ximately 80%. The lamp ser- vice lif e will be extended. OFF (High brightness mode): The brightness of ...

  • Compaq iP-25E - page 40

    E-40 Maintenance The projector is equipped with a built-in protection circuit to pre vent fire and breakdown due to f aults. When the LAMP/CO VER LED lights in red 䡬 Measures to be taken 1. Disconnect the power plug from the outlet. 2. Properly install the air filter . See "Air Filter Cleaning" on P age E-45. 3. Properly install the lam ...

  • Compaq iP-25E - page 41

    E-41 When the power has failed (When all the LED go off with the po wer ON) 䢇 Measures to be taken 1. Disconnect the power plug from the outlet. 2. Check the follo wing matters and perform the counter measure properly . Maintenance Is the ambient temperature in e xcess of 35 ° C (95 ° F)? Are the v entilation vents b loc ked? Is the air filter ...

  • Compaq iP-25E - page 42

    E-42 Replacement of the Lamp Unit Guidelines for the replacement of the pr ojection lamp used in this projector are described below . (The time may be shorter depending on usage conditions.) When the usage time exceeds the time described belo w, the likelihood of rupture increases, the projector will be for ced to turn off the projection lamp. Main ...

  • Compaq iP-25E - page 43

    E-43 1 Remo ve the lamp unit cover Using a minus scre wdr iver , loosen the screws of the lamp unit cov er , pull in the direction of the arro w , and remove the co ver . Maintenance 2 Loosen the mounting scre ws of the lamp unit Using a minus scre wdr iver , loosen the 2 screws of the lamp unit. 3 Pull out the lamp unit Hold the handle of the lamp ...

  • Compaq iP-25E - page 44

    E-44 Maintenance 5 Reset the lamp usage time Please perf or m the operation indicated below in the standb y mode (*). 6 Chec k that the indication of the lamp usage time has become "0 H" as illus- trated in the diagram to the right. If the usage time has not been reset, please reset it by follo wing Step 5 again. Chec k the lamp usage tim ...

  • Compaq iP-25E - page 45

    E-45 Maintenance 1 Remo ve the air filter cover Press the 2 tabs of the air filter co ver downw ard while s winging the cov er outward to remov e the air filter co ver . Air Filter Cleaning Procedure Cleaning the Air Filter The air filter is an impor tant par t that prev ents the intr usion of dust onto the optical par ts and other par ts inside th ...

  • Compaq iP-25E - page 46

    E-46 Tr oubleshooting Power does not come on Projection lamp does not light There is no image Image is distorted Image is blurred The image flickers The image is out of adjustment The color is not right There is no sound There is a snap sound from the cabinet The TEMP LED lights The LAMP/COVER LED lights in red The remote control will not work At t ...

  • Compaq iP-25E - page 47

    E-47 Repair Service Procedure • Bef ore asking for repair service, check the T roub leshooting section on page E-46 once more. If this check confirms a problem, contact the dealer where you bought the product. • When asking f or repair ser vice, provide y our dealer with the following inf or mation: Description of the problem (as many details a ...

  • Compaq iP-25E - page 48

    E-48 Model Name iP-25 Type LCD Panel Size Drive System Number of Pixels Arrangement Projection Lens Optical Source Image Size Color Reproducibility Brightness Scan Frequency Maximum Resolution At RGB signal input OHP Scanner PC Signal system (Analog Video signal RGB Input) Sync Signal Terminal Panel Video Signal system Input Terminal PC Audio Signa ...

Manufacturer Compaq Category Projector

Documents that we receive from a manufacturer of a Compaq iP-25E can be divided into several groups. They are, among others:
- Compaq technical drawings
- iP-25E manuals
- Compaq product data sheets
- information booklets
- or energy labels Compaq iP-25E
All of them are important, but the most important information from the point of view of use of the device are in the user manual Compaq iP-25E.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Compaq iP-25E, service manual, brief instructions and user manuals Compaq iP-25E. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Compaq iP-25E.

Similar manuals

A complete manual for the device Compaq iP-25E, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Compaq iP-25E by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Compaq iP-25E.

A complete Compaq manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Compaq iP-25E - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Compaq iP-25E, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Compaq iP-25E, that we can find in the current document
3. Tips how to use the basic functions of the device Compaq iP-25E - which should help us in our first steps of using Compaq iP-25E
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Compaq iP-25E
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Compaq iP-25E in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Compaq iP-25E?

Use the form below

If you did not solve your problem by using a manual Compaq iP-25E, ask a question using the form below. If a user had a similar problem with Compaq iP-25E it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)