Manual Wagner SprayTech 0278712C

20 pages 1.39 mb
Download

Go to site of 20

Summary
  • Wagner SprayTech 0278712C - page 1

    © 1995 Wagner Spray Tech 1 All rights reserved. PRINTED IN THE U. S. A. R Form No. 0278712C HIGH PERFORMANCE AIRLESS SPRA YER O WNER'S MANU AL Easy does it fr om setup to c lean up Questions? ... Need Help? Call Wagner toll-free if you have any comments or problems with this Wagner product. Call us first for answers fast... Wagner Technical S ...

  • Wagner SprayTech 0278712C - page 2

    © 1995 Wagner Spray Tech 2 All rights reserved. CONTENTS COMPONENTS .............................................................. 2 GENERAL DESCRIPTION ............................................. 2 Specifications ........................................................... 2 SAFETY PRECAUTIONS ........................................... 3-4 GROU ...

  • Wagner SprayTech 0278712C - page 3

    © 1995 Wagner Spray Tech 3 All rights reserved. SAFETY PRECA UTIONS This manual contains information which must be read and understood before using the equipment. When you come to an area which has one of the following symbols, pay particular attention and make certain to heed the safeguard. WARNING This symbol indicates a potential hazard which m ...

  • Wagner SprayTech 0278712C - page 4

    © 1995 Wagner Spray Tech 4 All rights reserved. WARNING EXPLOSION OR FIRE - Solvent and paint fumes can explode or ignite, causing property damage and/or severe injury. • Exhaust and fresh air introduction must be provided to keep the air within the spray area free from accumula- tion of flammable vapors. • Avoid all ignition sources such as s ...

  • Wagner SprayTech 0278712C - page 5

    © 1995 Wagner Spray Tech 5 All rights reserved. NOTE: Do not use more than 100 feet of extension cord. If you need to paint further than 100 feet from your power source, use more paint hose, not more extension cord. Shorter extension cords will ensure maximum electri- cal power for proper operation. GR OUNDING INSTRUCTIONS This product must be gro ...

  • Wagner SprayTech 0278712C - page 6

    © 1995 Wagner Spray Tech 6 All rights reserved. SETUP Attaching the pump to the stand. 1. Align the motor with the four holes on the back of the stand assembly. 2. Insert the four 5/16" x 1-3/4" screws through the holes on the back of the stand legs. Install the washer and nut over the end of each bolt and tighten with an adjustable wren ...

  • Wagner SprayTech 0278712C - page 7

    © 1995 Wagner Spray Tech 7 All rights reserved. PRESSURE RELIEF PR OCE- DURE Follow this procedure after the unit is assembled and before any operation which involves the spray gun such as cleaning and maintenance or changing tips or acces- sories. 1. Turn the pressure control knob counterclockwise to its lowest setting. 2. Turn the PRIME/SPRAY kn ...

  • Wagner SprayTech 0278712C - page 8

    © 1995 Wagner Spray Tech 8 All rights reserved. PRIMING Preparing to prime 1. Lay the unit back on its handle so that the inlet valve is facing up. Fill the inlet valve with water or with a light household oil. 2. Make certain that the PRIME/SPRAY knob is set to PRIME ( ) and that the pressure control knob is turned counterclockwise to the lowest ...

  • Wagner SprayTech 0278712C - page 9

    © 1995 Wagner Spray Tech 9 All rights reserved. 2. Turn the PRIME/SPRAY knob to PRIME ( ). 3. Turn the motor switch to ON. 4. Turn the pressure control knob clockwise to be- tween half and full pressure. You should be able to see the paint move through the suction tube to the pump. Let the unit prime 1 to 2 minutes after paint begins to flow throu ...

  • Wagner SprayTech 0278712C - page 10

    © 1995 Wagner Spray Tech 10 All rights reserved. the pressure control knob counterclockwise to its lowest setting and set the priming knob to PRIME ( ). Turn the motor switch to OFF and unplug the sprayer. If you expect to be gone more than 1 hour, follow the short term clean up procedure described in the CLEANUP section of this manual. Practice 1 ...

  • Wagner SprayTech 0278712C - page 11

    © 1995 Wagner Spray Tech 11 All rights reserved. spray pattern and possibly damaging the filter. This filter must be cleaned daily. If the material being used is old or contains hardened particles, then the filter should be cleaned approximately every 4 hours. If the filter is not cleaned at the proper time, it will plug from the top down. When th ...

  • Wagner SprayTech 0278712C - page 12

    © 1995 Wagner Spray Tech 12 All rights reserved. CLEAN UP Overnight storage Shutdown 1. Lock the gun by turning the gun safety switch parallel with the gun body. 2. Turn the pressure control knob counterclockwise to the minimum setting. 3. Turn the PRIME/SPRAY knob to PRIME ( ). 4. Turn the motor switch to OFF and unplug the sprayer. 5. For latex ...

  • Wagner SprayTech 0278712C - page 13

    © 1995 Wagner Spray Tech 13 All rights reserved. them into a container of water or appropriate solvent for the type of material with which you are painting. 11. Place the attached suction tube and return tube into a container of water or appropriate solvent for the type of material with which you are painting. 12. Increase the pressure to 1/2 the ...

  • Wagner SprayTech 0278712C - page 14

    © 1995 Wagner Spray Tech 14 All rights reserved. that it is parallel to the gun body. 14. Turn the motor switch to OFF. Preparing the sprayer for long term storage 1. Remove the tip assembly and raise the suction set above the cleaning solution. 2. Turn the motor to ON. 3. Turn the PRIME/SPRAY knob to SPRAY ( ). 4. Turn the pressure control knob c ...

  • Wagner SprayTech 0278712C - page 15

    © 1995 Wagner Spray Tech 15 All rights reserved. NOTE: The inlet valve must be oiled after every job. This will reduce or eliminate priming prob- lems the next time the sprayer is used. 4. Thoroughly clean the valve assembly with water or the appropriate solvent. Use a small brush. 5. If you have properly cleaned the valve and water drips out of t ...

  • Wagner SprayTech 0278712C - page 16

    © 1995 Wagner Spray Tech 16 All rights reserved. ...

  • Wagner SprayTech 0278712C - page 17

    © 1995 Wagner Spray Tech 17 All rights reserved. TROUBLESHOO TING Problem Cause Remedy The sprayer does not start up. The sprayer starts up but does not draw in paint when the PRIME/SPRAY knob is set to PRIME. The sprayer draws up paint but the pressure drops when the gun is triggered. The spray gun will not shut off. The spray gun leaks. The tip ...

  • Wagner SprayTech 0278712C - page 18

    © 1995 Wagner Spray Tech 18 All rights reserved. P arts Diagram – Final Assembl y ITEM PART NO. DESCRIPTION QTY. 1 0270590 Stand Weldment ............................. 1 2 9810107 Screw, 5/16" x 1-3/4" ...................... 4 3 9821505 Washer, 5/16" ................................. 4 4 9810197 Nut, 5/16" ................... ...

  • Wagner SprayTech 0278712C - page 19

    © 1995 Wagner Spray Tech 19 All rights reserved. 1 2 3 4 5 6 8 7 11 10 9 12 P arts Diagram – Suction Set Assembl y 0270174 ITEM PART NO. DESCRIPTION QTY. 1 0270133 Suction tube assembly .................... 1 (Includes Items 2 through 10) 2 0090622 Nut, suction ..................................... 1 3 0281314 Elbow, adapter, 3/4" x 1" ...

  • Wagner SprayTech 0278712C - page 20

    © 1995 Wagner Spray Tech 20 All rights reserved. R Wagner Spray Tech Corporation 1770 Fernbrook Lane Minneapolis, Minnesota 55447 Telephone (612) 553-7000 LIMITED W ARRANTY AIRLESS P AINT SPRA Y EQUIPMENT This product, manufactured by Wagner Spray Tech Corporation (Wagner), is warranted to the original retail purchaser against defects in material ...

Manufacturer Wagner SprayTech Category Paint Sprayer

Documents that we receive from a manufacturer of a Wagner SprayTech 0278712C can be divided into several groups. They are, among others:
- Wagner SprayTech technical drawings
- 0278712C manuals
- Wagner SprayTech product data sheets
- information booklets
- or energy labels Wagner SprayTech 0278712C
All of them are important, but the most important information from the point of view of use of the device are in the user manual Wagner SprayTech 0278712C.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Wagner SprayTech 0278712C, service manual, brief instructions and user manuals Wagner SprayTech 0278712C. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Wagner SprayTech 0278712C.

A complete manual for the device Wagner SprayTech 0278712C, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Wagner SprayTech 0278712C by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Wagner SprayTech 0278712C.

A complete Wagner SprayTech manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Wagner SprayTech 0278712C - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Wagner SprayTech 0278712C, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Wagner SprayTech 0278712C, that we can find in the current document
3. Tips how to use the basic functions of the device Wagner SprayTech 0278712C - which should help us in our first steps of using Wagner SprayTech 0278712C
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Wagner SprayTech 0278712C
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Wagner SprayTech 0278712C in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Wagner SprayTech 0278712C?

Use the form below

If you did not solve your problem by using a manual Wagner SprayTech 0278712C, ask a question using the form below. If a user had a similar problem with Wagner SprayTech 0278712C it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)